1. CanonFB310XP.ZIP Driver
2. CANON32.INI File Contents

CANON32.INI Driver File Contents (CanonFB310XP.ZIP)

[DS]
PATH=\twain_32\canon\fb310\
DSNAME=CANON32.DS
INTERFACE=CANON32.DLL
LAMPON=1
VERSION_INFO=V1.03
MANUFACTURER=Canon Inc.
PRODUCTFAMILY=CanoScan FB310 TWAIN-P Version 1.03
PRODUCTNAME=CanoScan FB310
MouseMove=0

[LANGUAGE]
LANGUAGE=English

[English]
&EASY=simple.dll
&BASIC=basic_e.dll
&EXPERT=expert_e.dll
TWDSM=avtwdsm.dll
SCANMODE=avscan.dll
UIDSM=uidsm.dll
Err999=(1)Power Off (2)Cable Failure
Err1=Can not find scanner.
Err2=Scanner R/W test failed.
Err3=Scanner connection failed.
Err4=Scanner RAM test failed.
Err5=Scanner RAM test failed.
Err6=Scanner DMA test/power cable failed.
Err7=Calibration failed.
Err8=Scanner internel error.
Err9=Paper feed error.
Err10=Sensor error. Unlock the scanner by turning the scanner lock to the Use position.
Err11=Transparency calibration error.
IDS_BADCAP=Bad capabilities error.
IDS_BADPROTOCOL=Bad protocol error.
IDS_BADVALUE=Bad value error.
IDS_BUMMER=Bummer error.
IDS_OPERATIONERROR=An operation error just occurred.
IDS_LOWMEMORY=Low Memory Condition encountered, free up some memory and try again.
IDS_MAXCONNECTIONS=Twain is used by other apps, please close some apps and try again.
IDS_NODS=No Data Source found.
IDS_SEQERROR=DG DAT MSG is out of expected sequence.
IDS_SUCCESS=Success message from detailed error request ??
IDS_APINIFALSE=The application is not yet initialize,
IDS_APINIFALSE1=please execute ApSetup.exe to add information.
IDS_SCANNERERROR=Scanner not ready
IDS_SCANNERERROR1=It may be either:
IDS_SCANNERERROR2=1.) Power Off
IDS_SCANNERERROR3=2.) Cable Failure
IDS_SCANNERERROR4=Please check again.
IDS_NOPAPER=No paper in Auto Document Feeder
IDS_NOPAPER1=Please load paper, and Try again.
IDS_NODISK=Not enough disk space
IDS_NODISK1=Please clean up disk and try again.
IDS_BADPARAM=Scanner parameters are not correct.
IDS_WRITEERROR=Write to file error.
IDS_WRITEERROR1=It may be either:
IDS_WRITEERROR2=1.) Disk full
IDS_WRITEERROR3=2.) Disk write protect
IDS_WRITEERROR4=Please check again.
IDS_ABOUT=Cancel the action.
IDS_UNKNOWERROR=Unknown Error value.
IDS_TRANSFER=Transfert
IDS_CHUNKY=Data Chunky && Transfer
IDS_MEMORY_P=Buffered Memory  /  P
IDS_MEMORY_C=Buffered Memory  /  C
IDS_NATIVE=Native Memory
IDS_NATIVE_P=Native Memory / P
IDS_DISK=Disk File
IDS_DISK_P=Disk File  /  P
IDS_MEMORY=Buffered Memory
IDS_SCAN=Scanning...
IDS_PREVIEW=Preview...
IDS_TESTSCANNER=Scanner Testing
IDS_CONNECTING=Connecting scanner
IDS_CANCEL=Cancel
IDS_TRANSFERMODE=Transfer Mode :
CaliTitle=Do Calibrating...
IDS_PUTPAPERMSG=Put calibration sheet on scanner
IDS_WAIT=Please Wait...
IDS_BADSIZE=Scan size < 64 pixel or 0.5 inch
IDS_BADWIDTH=Scan width is too large
IDS_PRINTWORKING=There are print jobs in processing, please wait till all print jobs done.

[UI Version]
UI Num=3
0=&EASY
1=&BASIC
2=&EXPERT

[&EASY]
function=CreateSimpleDialog
Curve=0

[&BASIC]
function=_CreateBasicDialog
Curve=0

[&EXPERT]
function=_CreateExpertDialog
Curve=1