\HELP\SCO\SCOUNIX.TXT
NETGEAR FA310TX Fast Ethernet PCI Adapter
-----------------------------------------
Driver Installation for SCO UNIX V.3.2.4X (TCP/IP v1.2X)
--------------------------------------------------------
Getting Started
---------------
The necessary files for driver installation for SCO UNIX are stored
in a compressed format.
Installation Procedure
----------------------
1. Login to the network as root. (On maintenance mode)
2. Copy the compressed file ngrXXX.Z (XXX indicates the version number,
eg. ngr224.Z) from the \SCO directory of the driver diskette into
your hard disk.
3. Use doscp command to copy the SCOUNIX Driver into the UNIX directory.
example:
# cd /temp
# doscp /<path>/ngr224.Z ngr224.Z
4. Uncompress ngrXXX.Z to ngrXXX,
example:
# uncompress ngr224
5. Copy the files to a blank 3.5" floppy diskette.
example:
#dd if=ngr224 of=/dev/fd0135ds18
Mark the diskette:
NETGEAR FA310TX Fast Ethernet PCI Adapter LLI driver
Rel.02.24
4. Run custom from the menu selection.
Custom -> Install -> A New Product -> Entire Product
5. Put the distribution diskette in the drive and select continue.
6. When prompted for distribution floppy 1, press enter.
7. When custom has completed, remove the diskette and quit custom.
8. Add a chain by executing the netconfig command
example:
#netconfig
9. A menu similar to the following appears on the screen:
Available options:
1. Add a chain
2. Remove a chain
3. Reconfigure an element in a chain
4. Quit
Select option : 1
10. The following prompt appears:
Num Name Description
1. nfs SCO NFS Runtime System for SCO Unix
2. sco_ipx SCO IPX/SPX for UNIX
3. sco_tcp SCO TCP/IP for UNIX
Select top level of chain to Add or q to quit: 3
11. It will show all drivers available in the system and select next
level of chain to Add or to quit. Select "ngrpci0". This value
varies according to your card number.
12. The following prompt appears:
Add chain sco_tcp->ngrpci0 (y/n): y
Note:
Add chain sco_tcp -> ngrpci unit 0 (y/n); install card # 1
Add chain sco_tcp -> ngrpci unit 1 (y/n); install card # 2
Add chain sco_tcp -> ngrpci unit 2 (y/n); install card # 3
Add chain sco_tcp -> ngrpci unit 3 (y/n); install card # 4
It depends on card number.
13. If you are configuring board 0, the following messages will
prompt for specifying the access type of PCI bus.
**************************************************************
* !!!! Note !!!!! *
* This driver only support the PCI BIOS call (in 32-bit *
* protected mode). *
* *
* If your systems does not support these BIOS calls, there *
* will be errors during boot time. *
**************************************************************
14. The following message appears:
Please choose the line speed that you want............
0. Use default value.
1. 10 MB/sec mode.
2. 100 MB/sec mode.
3. Automatic detection between 10 MB/sec and 100 MB/sec mode.
Enter the line speed selection number (0 1 2 3)[0] or 'q' to quit: 0
Note: The default value of line speed is "Automatic detection".
The "line speed" and "media mode" options must be used
together. When setting the line speed to "Automatic
detection", the "media mode" must be set to "Use default
value".
15. The following message appears:
Please choose the media mode that you want...............
0. Use default value.
1. Point to point full duplex twisted pair connection.
2. Twisted pair connection.
Note: The default value of line speed is "Automatic detection".
The "line speed" and "media mode" options must be used
together. When setting the line speed to "Automatic
detection", the "media mode" must be set to "Use default
value".
16. Installing SCO TCP/IP over ngrpci0
Please enter the following information in order to configure ngrpci0
Enter the internet address of this interface: xxx.xxx.xxx.xxx
Enter the netmask for this interface(default: 255.255.255.0):
Does the interface use a broadcast address of all 1's? (y/n)
(default: y):
Enter the broadcast address for this interface
(default: 202.39.74.255):
Note: Specify the subnet mask for the interface. Please consult the
systems administrator if it is unknown. The default subnet mask
is 255.255.255.0.
17. It will show the information you configure. If all values are correct,
type "y". Otherwise, answer "n" .
18. The following message appears:
XX Pseudo ttys are currently configured, do you want to:
1. Add Pseudo ttys
2. Remove Pseudo ttys
Select an option or enter q to quit [q]: q
19. TCP/IP configuration is completed. The main menu reappears on the
screen. Select "q" to quit configuration
20. The following message appears:
Do you want to relink to kernel now ? y
21. The following message appears:
Do you want this kernel to boot by default (y/n) y
22. The following message appears:
Do you want the kernel environment rebuilt (y/n) y
23. Reboot UNIX by typing the following:
#init 0
Installation for multi-cards:
-----------------------------
This installation is for drivers of SCO UNIX (Runtime v3.2.4x) with
TCP/IP v.1.2.
1. It is allowable to have four network interface cards in a system.
2. Support geteway function. (routing function)
3. Statistical function is added when the following command is
executed:
# netstat -i
Name Mtu Network Address Ipkts Ierrs Opkts Oerrs Collis
ngrpci0 1500 168.8 unix 556 0 890 0 0
ngrpci1 1500 202.39.74 unix2 423 0 423 0 0
lo0 2048 170.23 localhost 180 0 180 0 0
Note: The IRQ number must match the value set in ROM BIOS. Please
check it before you provide this value to the system. Most
of the time, the IRQ number for the PCI bus can be accessed
by pressing the [DEL] key during power on and choosing the proper
select item to set the IRQ number for the PCI device.
Example: ROM PCI/ISA BIOS (2A4X5C31)
PCI/GREEN FUNCTION SETUP
AWARD SOFTWARE, INC.
Press the [DEL] key --> PCI/GREEN FUNCTION SETUP
Slot 3 Using INT# : A-PIRQ1
.
.
PIRQ1# Connect IRQ: 5 By Single
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.