#
| README file for
|
| ELSA QuickStep 1000
| Version 2.28
|
| Copyright (c) 1993-98 ELSA AG, Aachen (Germany)
|
| ELSA AG Internet : http://www.elsa.de
| Sonnenweg 11 LocalWeb : +49-(0)241-938800
| D-52070 Aachen CompuServe : GO ELSA
|
| ELSA Inc. Internet : http://www.elsa.com
| 2231 Calle De Luna CompuServe : GO ELSA
| Santa Clara, CA 95054
| USA
|
| ELSA Asia Inc. Internet : http://www.elsa.com
| 7F-11, No. 188, Sec. 5 CompuServe : GO ELSA
| Nanking East Road
| Taipei 105
| Taiwan, R. O. C.
|
| 01/05/98
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Table of Contents
1. Overview
2. Contents
3. Installation
4. Notes
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1. Overview:
This file contains notes and changes to the
ISDN drivers.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
2. Contents:
This directory contains the following files:
README.TXT this file
LIESMICH.TXT german version of this README.TXT
CAPI.INI INI-Datei des CAPI-Treibers unter Win 3.1
2.1 [DRIVER]
DLL (dynamic link library) for 1TR6 (national ISDN):
ISDNCAPX.DLL CAPI version 1.1 driver for ELSA QuickStep 1000
D channel protocol : 1TR6 (national ISDN)
B channel protocols: HDLC transparent, bit transparent,
X.75, T.70NL, V.120
ISO 8208 (X.25), T.90
ISDNC20X.DLL CAPI version 2.0 driver for ELSA QuickStep 1000
D channel protocol : 1TR6 (national ISDN)
B channel protocols: HDLC transparent, bit transparent,
X.75, T.70NL, V.120
ISO 8208 (X.25), T.90
DLL (dynamic link library) for DSS1 (EURO-ISDN):
DSS1CAPX.DLL CAPI version 1.1 driver for ELSA QuickStep 1000
D channel protocol : DSS1 (EURO-ISDN)
B channel protocols: HDLC transparent, bit transparent,
X.75, T.70NL, V.120
ISO 8208 (X.25), T.90
DSS1C20X.DLL CAPI version 2.0 driver for ELSA QuickStep 1000
D channel protocol : DSS1 (EURO-ISDN)
B channel protocols: HDLC transparent, bit transparent,
X.75, T.70NL, V.120
ISO 8208 (X.25), T.90
CAPI.DLL for CAPI 1.1, DOS-TSR expected
CAPI20.DLL for CAPI 2.0, DOS-TSR expected
2.2 [UTILS]
clrauto.exe releases autoexec.bat to not load DOS CAPI
automaticly,
isdnmon.exe ELSA ISDNmonitor forWindows 3.1x
gocapi.exe starts the CAPI.DLL/CAPI20.DLL
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3. Installation:
The following illustration shows the mounting bracket of
your ISDN plug and play adapter board :
_____
\ |
| |
| |
| |
| |
|___|
|___|<- ISDN line connector
| |
| o |<- ISDN connection status display (yellow LED)
| o |<- ISDN interface status display (green LED)
|___|
_
|
|
|
|
________________________________|
| _|
| |_ <- ISDN line connector
| |
| o<- yellow LED
| _ __ o<- green LED
|___| |____________________| |__|
The ISDN plug and play adapter board is full software-
configurable and has NO jumper.
- - - - - - - - - - - - - - - - - - - - - - - -
a.) Installation with plug and play:
If you system supports plug and play you just have to
install the driver without any parameters. Use the setup-
program from the directory WIN31.
- - - - - - - - - - - - - - - - - - - - - - - -
b.) Installation without plug and play:
If your system doesn't support plug and play, you also have
to install the DLL's with the setup tool from the windows
directory. The driver uses the following defaults:
I/O-address : 0x160h
IRQ : 15
If these parameters are used by an other component in your
system, you have to change the defaults as shown below:
- exit Windows and move to the directory \WINDOWS
- open the file CAPI.INI with an ASCII editor
(e.g. EDIT CAPI.INI)
- search for the section [CAPI PARAM]
- insert the line "ADDPARAM = [/a<I/O-addresse>] [/r<IRQ>]"
e.g.: ADDPARAM = /a160 /r12
- start windows
- to takeover the changes start the setup tool from the
program group "ELSA ISDN Utilities" and go though it
without changes.
- if there is an application active, whitch uses the DLL,
for example cFos or the ISDNmon, you have to restart
Windows for the changed CAPI.INI is read again
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
4. Notes:
V.120 under CAPI 1.1 and CFOS (version newer than 07/15/96):
Enter the following AT-command:
AT B12 S17=1 S76=1
Now, the ISDN adapter board tries to get a V.120 connection
erverytime you dial "ATDn" (n = number)..
If you want to get back to X.75 mode, you have to enter:
AT&F
- - - - - - - - - - - - - - - - - - - - - - - -
V.120 under CAPI 2.0 and CFOS (version newer than 07/15/96):
Enter the following AT-command:
AT B12 S17=1 S76=1
Now, the ISDN adapter board tries to get a V.120 connection
erverytime you dial "ATDn" (n = number)..
If you want to get back to X.75 mode, you have to enter:
AT&F
- - - - - - - - - - - - - - - - - - - - - - - -
The latest information you will always find in the
ELSA LocalWeb or on our homepage.
Have fun with your ISDN board.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.