10/100M Fast Ethernet PCMCIA Adapter Installation
for NetWare Server 5.0 Driver
Contents
ÍÍÍÍÍÍÍÍ
Introduction
Getting Started
First time installation from the install menu
The other time installation from the install menu
Modifying an existing NetWare 5.0 Server
Introduction
ÍÍÍÍÍÍÍÍÍÍÍÍ
This installation assumes that the PC Card drivers are working
properly. Please consult INST_DOS.TXT for help with PC Card
Drivers. Getting Started will describe the installation
instructions.
Getting Started
ÍÍÍÍÍÍÍÍÍÍÍÍÍÍ
******************************************************************
* Notes: *
* The PC Card should be enabled by Card Enabler. *
* Please run ENFP16.EXE before starting LAN driver. *
* *
* Two alternatives to enable the 10/100M Fast *
* Ethernet PCMCIA Adapter: *
* *
* 1. Issue an executive file: *
* *
* At the DOS prompt, type: *
* *
* ENFP16 [/iop:XXX] [/irq:X] *
* *
* For more details, refer to INST_DOS.TXT. *
* *
* 2. Modify CONFIG.SYS *
* *
* Add the following instruction to CONFIG.SYS file *
* *
* DEVICE=<PATH>\ENFP16.EXE [/iop:XXX] [/irq:X] *
* *
* ; <PATH> is a directory containing ENFP16.EXE *
* ; Please refer to the INST_DOS.TXT file for details. *
******************************************************************
First time installation from the install menu
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Start the NetWare Server.
> CD \NWSERVER
> SERVER
Execute "LOAD NWCONFIG" after booting up. Type:
LOAD NWCONFIG
Select "Driver Options", -> "Configure network drivers", and
-> "Select a driver".
Press <Insert> key to install an unlisted driver.
Please insert driver diskette into floppy disk drive.
Press <F3> to specify a different <PATH>. <PATH> is directory
which include both FP16.LAN and FP16.LDI
Ex. A:\NETWARE\SERVER\NW50
Select "FP16.LAN ...".
Select "Save parameters and load driver" after configuring adpter
setting.
NetWare server will loading/binding driver automatically.
Specify "I/O port" and "Interrupt number" while NetWare server is
loading the driver, and these values should be consistent with the
values set by ENFP16.EXE.
After the driver has been loaded, check whether all the frame types
you want are specified for this driver in AUTOEXEC.NCF.
The other time installation from the install menu
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Start the NetWare Server.
> CD \NWSERVER
> SERVER
Execute "LOAD NWCONFIG" after booting up. Type:
LOAD NWCONFIG
Select "Driver Options", -> "Configure network drivers", and
-> "Select a driver".
Select "FP16.LAN ..." in Select a driver window.
Select "Save parameters and load driver" after configuring adpter
setting.
NetWare server will loading/binding driver automatically.
Specify "I/O port" and "Interrupt number" while NetWare server is
loading the driver, and these values should be consistent with the
values set by ENFP16.EXE.
After the driver has been loaded, check whether all the frame types
you want are specified for this driver in AUTOEXEC.NCF.
Modifying an existing NetWare 5.0 Server
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Please insert driver diskette into floppy disk.
Copy all provided LAN files into your dos directory
which include SERVER.EXE.
Ex. >COPY A:\NETWARE\SERVER\NW50\FP16.LAN C:\NWSERVER
>COPY A:\NETWARE\SERVER\NW50\FP16.LDI C:\NWSERVER
Start the NetWare Server.
> CD \NWSERVER
> SERVER
From the Novell Server side, execute "LOAD NWCONFIG". Type:
LOAD NWCONFIG
Select <NCF files Options>
Select <Edit AUTOEXEC.NCF file>
Add the following commands into the server's AUTOEXEC.NCF file.
Search Add C:\NWSERVER
LOAD FP16 PORT=300 INT=3 FRAME=Ethernet_802.3 NAME=FP16_1_E83
BIND IPX FP16_1_E83 NET=1111
LOAD FP16 PORT=300 INT=3 FRAME=Ethernet_802.2 NAME=FP16_1_E82
BIND IPX FP16_1_E82 NET=1113
LOAD FP16 PORT=300 INT=3 FRAME=Ethernet_II NAME=FP16_1_EII
BIND IPX FP16_1_EII NET=1115
LOAD FP16 PORT=300 INT=3 FRAME=Ethernet_SNAP NAME=FP16_1_ESP
BIND IPX FP16_1_ESP NET=1117
Note: the PORT and INT parameters should be set as the values
which are set by ENFP16.EXE.
Restart the server again.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.