Command Quick Reference ------------------------- &$ HELP, Ampersand Commands Mn n=0 Speaker Off A/ Repeat Last Command n=1 Speaker On Until CD A> Continuously Repeat Command n=2 Speaker Always On AT Command Mode Prefix n=3 Speaker Off During Dial A Answer Call On n=0 Return Online Bn n=0 V32 Mode/CCITT Answer Seq n=1 Return Online & Retrain n=1 Bell Answer Seq P Pulse Dial Dn Dial a Telephone Number Qn n=0 Result Codes Sent n=0..9#*TPR,;"W@!()-& n=1 Quiet (No Result Codes) DL Dial Last Phone Number n=2 Verbose/Quiet On Answer DSn Dial Stored Phone Number n=3 Ring Message (Voice mode) D$ HELP, Dial Commands Sr=n Sets Register "r" to "n" En n=0 No Command Echo Sr? Query Register "r" n=1 Echo Command Chars S$ HELP, S Registers Fn n=0 Online Echo T Tone Dial n=1 No Online Echo Vn n=0 Numeric Responses Hn n=0 On Hook (Hang Up) n=1 Verbal Responses n=1 Off Hook Xn n=0 Basic Result Codes In n=0 Product Code n=1 Extended Result Codes n=1 Checksum n=2-4 Advanced Result Codes n=2 RAM Test Yn n=0 Next reset to &W0 settings n=3 Product ID String n=1 Next reset to &W1 settings n=4 Current Settings n=2 Next reset to &F0 settings n=5 NVRAM Settings n=3 Next reset to &F1 settings n=6 Link Diagnostics n=4 Next reset to &F2 settings n=7 Product Configuration Z n=0 Y setting determines reset n=8 OK n=1 Reset to &W0 settings n=9 PnP ID n=2 Reset to &W1 settings n=10 ERROR n=3 Reset to &F0 settings n=11 Link Diagnostics n=4 Reset to &F1 settings Ln n=0 Lowest Speaker Volume n=5 Reset to &F2 settings n=1 Low Speaker Volume +++ Escape Code n=2 Med Speaker Volume $ HELP, Command Summary n=3 Hi Speaker Volume Dial Commands ------------------------- 0-9 Digits to Dial * Auxiliary Tone Dial Digit # Auxiliary Tone Dial Digit T Tone Dialing P Pulse Dialing R Call an Originate Only Modem , Pause (Wait for S8 Time) ; Remain in Command Mode After Dialing " Used to Dial Alpha Phone #'s W Wait for Dial Tone (X2,X4) @ Wait for an Answer (X3,X4) ! Flash Switch Hook & Wait for credit card Ampersand Commands ------------------------- &An n=0 Disable /ARQ Result Codes &Pn n=0 N.American Pulse Dial n=1 Enable /ARQ Result Codes n=1 UK Pulse Dial n=2 Enable /Modulation Codes &Rn n=0 CTS Follows RTS n=3 Enable /Extra Result Codes n=1 Ignore RTS &Bn n=0 Floating DTE Speed n=2 RX to DTE/RTS high n=1 Fixed DTE Speed &Sn n=0 DSR Always On n=2 DTE Speed Fixed When ARQ n=1 Modem Controls DSR &Cn n=0 CD Always On &Tn n=0 End Test n=1 Modem Controls CD n=1 Analog Loopback (ALB) &Dn n=0 Ignore DTR n=3 Digital Loopback (DLB) n=1 On-Line Command Mode n=4 Grant Remote DLB n=2 DTE Controls DTR n=5 Deny Remote DLB n=3 DTE Controls DTR and reset n=6 Remote Digital Loopback &Fn n=0 Load Factory Configuration n=7 Remote DLB With Self Test n=1 Hardware Flow Control Cnfg. n=8 ALB With Self Test n=2 Software Flow Control Cnfg. &Un Lowest Link Speed Limit &Gn n=0 No Guard Tone n=0 Disabled n=1 550 Hz Guard Tone n=1 300 bps n=2 1800 Hz Guard Tone n=2 1200 bps &Hn n=0 Disable TX Flow Control n=3 2400 bps n=1 CTS n=4 4800 bps n=2 Xon/Xoff n=5 7200 bps n=3 CTS and Xon/Xoff n=6 9600 bps &In n=0 Disable RX Flow Control n=7 12000 bps n=1 Xon/Xoff n=8 14400 bps n=2 Xon/Xoff Chars Filtered n=9 16800 bps n=3 HP Enq/Ack Host Mode n=10 19200 bps n=4 HP Enq/Ack Terminal Mode n=11 21600 bps n=5 Xon/Xoff for non-ARQ Mode n=12 24000 bps &Kn n=0 Disable Data Compression n=13 26400 bps n=1 Auto Data Compression n=14 28800 bps n=2 Enable Data Compression n=15 31200 bps n=3 Selective Data Compression n=16 33600 bps &Mn n=0 Normal Mode n=17 Minimum link rate 33333 bps n=4 ARQ/Normal Mode n=18 Minimum link rate 37333 bps n=5 ARQ Mode n=19 Minimum link rate 41333 bps &Nn n=0 Highest Link Speed n=20 Minimum link rate 42666 bps n=1 300 bps n=21 Minimum link rate 44000 bps n=2 1200 bps n=22 Minimum link rate 45333 bps n=3 2400 bps n=23 Minimum link rate 46666 bps n=4 4800 bps n=24 Minimum link rate 48000 bps n=5 7200 bps n=25 Minimum link rate 49333 bps n=6 9600 bps n=26 Minimum link rate 50666 bps n=7 12000 bps n=27 Minimum link rate 52000 bps n=8 14400 bps n=28 Minimum link rate 53333 bps n=9 16800 bps n=29 Minimum link rate 54666 bps n=10 19200 bps n=30 Minimum link rate 56000 bps n=11 21600 bps n=31 Minimum link rate 57333 bps n=12 24000 bps &Wn n=0 Store Configuration 0 n=13 26400 bps n=1 Store Configuration 1 n=14 28800 bps &Yn n=0 Destructive n=15 31200 bps n=1 Destructive/Expedited n=16 33600 bps n=2 Nondest./Expedited n=17 33333 bps n=3 Nondest./Unexpedited n=18 37333 bps &Zn=s Store Phone Number n=19 41333 bps &Zn=L Store Last Phone Number n=20 42666 bps &Zn? Query Phone Number n=21 44000 bps n=22 45333 bps n=23 46666 bps n=24 48000 bps n=25 49333 bps n=26 50666 bps n=27 52000 bps n=28 53333 bps n=29 54666 bps n=30 56000 bps n=31 57333 bps S Register Functions ------------------------- S0 Ring to Answer On S1 Counts # of Rings S2 Escape Code Char S3 Carriage Return Char S4 Line Feed Char S5 Backspace Char S6 Wait Time/Dial Tone (sec) S7 Wait Time/Carrier (sec) S8 Comma Time (sec) S9 Carrier Detect Time (1/10sec) S10 Carrier Loss Time (1/10sec) S11 Dial Tone Spacing (msec) S12 Escape Code Time (1/50sec) S13 Bit Mapped 1 = Reset On DTR Loss 2 = Reduced Non-ARQ TX Buffer 4 = Set DEL=Backspace 8 = Do DS0 On DTR 16 = Do DS0 On Reset 32 = Reserved 64 = Disable Quick Retrains 128 = Escape Code Hang Up S14 Reserved S15 Bit Mapped 1 = MNP/V.42 Disabled in V.22 2 = MNP/V.42 Disabled in V.22bis 4 = MNP/V.42 Disabled in V.32 8 = Disable MNP Handshake 16 = Disable MNP Level 4 32 = Disable MNP Level 3 64 = Unusual MNP-Incompatibility 128 = Disable V.42 136 = Disable V.42 Detect Phase S16 Test Modes 1 = Reserved 2 = Dial Test 4 = Reserved 8 = Reserved 16 = Reserved 32 = Reserved 64 = Reserved 128 = Reserved S17 Reserved S18 &Tn Test Timeout (sec) S19 Inactivity Timeout (min) S20 Reserved S21 Break Length (1/100sec) S22 Xon Char S23 Xoff Char S24 Reserved S25 DTR Recognition Time (1/100sec) S26 Reserved S27 Bit Mapped 1 = V.21 Mode 2 = Disable TCM 4 = Disable V.32 8 = Disable 2100hz 16 = Enable V.23 Fallback 32 = Disable V.32bis 64 = Disable V.42 Selective Reject 128 = Software Compatibility Mode S28 V.32 Handshake Time (1/10sec) S29 V.21 answer mode fallback timer S30 Reserved S31 Reserved S32 Connection bit mapped operations 1 = V.8 Call Indicate enable 2 = Enable V.8 mode 4 = Disable V.FC modulation 8 = Disable V.34 modulation 16 = Disable V.34+ modulation 32 = Reserved 64 = Reserved 128 = Reserved S33 V.34 & V.34+ Connection setup Bit Mapped control flags 1 = Disable 2400 Symbol rate 2 = Disable 2743 Symbol rate 4 = Disable 2800 Symbol rate 8 = Disable 3000 Symbol rate 16 = Disable 3200 Symbol rate 32 = Disable 3429 Symbol rate 64 = Reserved 128 = Disable Shaping S34 V.34 & V.34+ Connection setup Bit Mapped control flags 1 = Disable 8S-2D trellis encoding 2 = Disable 16S-4D trellis encoding 4 = Disable 32S-2D trellis encoding 8 = Disable 64S-4D trellis encoding 16 = Disable Non linear coding 32 = Disable TX level deviation 64 = Disable Pre-emphasis 128 = Disable Pre-coding S35 Reserved S36 Reserved S37 Reserved S38 Disconnect Wait Time (sec) S39 Reserved S40 Reserved S41 ReservedDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.