BroMax CF Ethernet Card Driver Diskette (Ver 1.00) Overview TOPIC ====================================== 1. DISKETTE CONTENTS 2. CLIENT DRIVER 3. SOCKET and CARD SERVICES INSTALLATION ADVISORY 4. DIAGNOSTIC PROGRAM 5. NETWARE DOS ODI DRIVER 6. PACKET DRIVER 7 NDIS DRIVER FOR OS2 LAN SERVER 8. NDIS DRIVER FOR WINDOWS FOR WORKGROUPS 3.11 9. NDIS DRIVER FOR LAN MANAGER V2.1 10. NDIS 3.1 DRIVER FOR WINDOWS 95 11. NDIS 3.1 DRIVER FOR WINDOWS 98 12. NDIS 3.1 DRIVER FOR WINDOWS NT 3.51 13. NDIS 3.1 DRIVER FOR WINDOWS NT 4.0 14. NDIS 3.1 DRIVER FOR WINDOWS 2000 [1] DISKETTE CONTENTS Files and Subdirectories Contents -------------------------------------------------------------------- \BCN0010T Tag File \iPortCF.INF Windows 95 Installation File \DIAG.EXE PCMCIA Card Diagnostic Program \INSTALL.EXE PCMCIA Installation Program \CARDGO.EXE PCMCIA Client Driver \README.TXT This file \NETWARE.ODI Directory of Novell Netware DOS ODI Driver \PKTDRV Directory of FTP Compliant Packet Driver Directory \OS2 Directory of NDIS V2.0 Driver for OS2 LAN Server \NDIS Directory of NDIS V2.0 Driver \WFW311 Directory of NDIS V2.0 Enhance Mode Driver for WFW311 \MSLANMAN.DOS Directory of NDIS V2.0 Driver for Lan Manager V2.1 \LANTASTI.V60 Directory of NDIS V2.0 Driver for Lantastic V6.0 \WIN9X Directory of NDIS V3.1 Driver for Windows 95 and 98 \WINNT Directory of NDIS V3.1 Driver for Windows NT 3.51 and 4.0 \WIN2000 Directory of NDIS V3.1 Driver for Windows 2000 [2] CLIENT DRIVER (For DOS and Windows 3.1 Only) The Client Driver is a PCMCIA controller enable program. This enable program only need for DOS and Windows 3.1 system. To load the client driver, type CARDGO [/IRQ=x][/IO=xxx][/MEM=xxxx][/?] in DOS command line, or DEVICE=[PATHNAME]CARDGO.EXE [/IRQ=x][/IO=xxx][/MEM=xxxx] in config.sys file. where: [/IRQ=x] This specifies the hardware interrupt (IRQ) where your card will be indicated. The valid IRQs are 3,4,5,9,10,11. [/IO=xxx] This specifies the I/O address. The valid ports are 300, 320,340,360. [/MEM=xxxx] This specifies the memory window address. The valid MEMs are D000, D400, D800, DC00. [/?] This specifies to indicate the program to display all the possible syntax only. The default syntax is: CARDGO /IRQ=5 /IO=300 /MEM=D400 After you executed the CARDGO.EXE, you will see the following display for make sure install successful. Especially you must see the Node ID value. Slot : 0 (for example) IRQ : 5 (for example) IO PORT : 300 (for example) Memory : D400 (for example) Here is the list of error messages the driver may display and correction method we suggested: [Error 1] "The PCMCIA controller is not present or recognized" There is no PCMCIA controller on your computer. Find another computer with PCMCIA controller to use it. [Error 2] "There is no card in PCMCIA slot. Insert the card" Card is not found in PCMCIA slot. Insert it. [Error 3] "The card in PCMCIA slot is not BroMax Ethernet Card. Insert it" Card is not found in PCMCIA slot. Insert it. [Error 4] "The I/O ports do not respose. Change another one" I/O ports do not response. Change anther one using /IO=xxx. [Error 5] "The I/O ports specified are invalid. Change another one" I/O ports are invalid. Change anther one using /IO=xxx. [Error 6] "The IRQ specified is invalid. Change another one" IRQ setting is invalid. Change anther one using /IRQ=x. [Error 7] "The memory address specified is invalid. Change another one" Memory setting is invalid. Change another one using /MEM=xxxx. [Error 8] "Enabler has been registered" This Client Driver has been registered once. Don't run it again. [Error 9] "Enabler can't registered as a client", or "Can't map memory", or "Configuration can't be requested" These three errors are concerned with Socket and Card services of the PCMCIA controller. Try another third part Socket and Card service support this PCMCIA controller. [3] SOCKET and CARD SERVICES INSTALLATION ADVISORY For those who installed EMM386.EXE in your config.sys, please exclude memory address D400-D7FF from your system. CF Ethernet Card Enabler program will use this space to read Ethernet ID and CIS from on-board serial EEPROM. [Example] DEVICE=EMM386.EXE NOEMS X=D400-D7FF or DEVICE=EMM386.EXE NOEMS X=D000-DFFF For those who installed Card and Socket Services device driver in your config.sys, please run CARDGO.EXE(see Client Driver) after those device drivers. The default configuration is INT=5, PORT=300 and MEM=D400. [Phoenix PCM+ V3.0] DEVICE=C:\PCM3\CNFIGNAM.EXE /SETUP-DEFAULTS DEVICE=C:\PCM3\PCMSS.EXE DEVICE=C:\PCM3\PCMCS.EXE DEVICE=C:\PCM3\PCMRMAN.SYS DEVICE=C:\PCM3\PCMSCD.EXE DEVICE=CARDGO.EXE [SystemSoft CardSoft V3.1] DEVICE=C:\CARDSOFT\SS365SL.EXE //Socket Service for Intel Compatible // DEVICE=C:\CARDSOFT\CS.EXE DEVICE=C:\CARDSOFT\CSALLOC.EXE DEVICE=CARDGO.EXE [Award CArdware V2.0] DEVICE=C:\CARDWARE\SSPCIC.EXE DEVICE=C:\CARDWARE\PCCS.EXE DEVICE=C:\CARDWARE\PCRM.EXE /AUTODETECT DEVICE=CARDGO.EXE [Note] Please do not use PCENABLE.EXE [AMI AMICARDZ] DEVICE=C:\AMI\SSSL.SYS DEVICE=C:\AMI\AMICS.SYS DEVICE=CARDGO.EXE [Note] Please do not use PCBE.SYS [Databook CardTalk V3.02] DEVICE=C:\CARDTALK\TMB250.SYS /io:240 DEVICE=C:\CARDTALK\CTALKCS.EXE DEVICE=C:\CARDTALK\CARDTALK.EXE /A /IOW=300-31F /MEMW=D000-D7FF DEVICE=CARDGO.EXE [IBM Thinkpad Socket and Card Services V2.12] DEVICE=C\EMM386.EXE NOEMS I=B000-B7FF X=C800-CFFF X=D000-DFFF DEVICE=C:\THINKPAD\IBMDSS01.SYS /D DEVICE=C:\THINKPAD\IBMDOSCS.SYS DEVICE=C:\THINKPAD\DICRMU01.SYS /MA=C800-DFFF DEVICE=C:\THINKPAD\$ICPMDOS.SYS [4] DIAGNOSTIC PROGRAM DIAG.EXE is a complete test program that users can make sure if the card is good or not. It provides the following card test functions: . IRQ verify . IO base verify . RAM test . Card Node ID test . Internal Loopback test . External Loopback test [Note] Before execute diagnostic program, you must make sure the client driver, CARDGO.EXE, is installed. [5] Netware DOS ODI Driver This directory contains Ethernet DOS ODI driver IPORTODI.COM that supports NetWare 3.x and 4.x, NetWare Lite and other ODI interface application. IPORTODI.COM : DOS/ODI Driver for NetWare 3.x and 4.0. The following instructions let you to install Novel NetWare Ver. 386 DOS ODI Driver : 5.1 How To Install --------------- You need following five files to install DOS ODI DRIVER. a. LSL.COM ---- supported by Novell b. IPORTODI.COM ---- Novell DOS ODI Driver ,supported by manufacturer c. IPXODI.COM ---- supported by Novell d. NETx.COM ---- supported by Novell or EMSNETx.EXE or XMSNETx.EXE e. NET.CFG ---- optional,configuration file After boot your workstation, type following comments on the console: LSL <Enter> IPORTODI <Enter> IPXODI <Enter> NETx <Enter> then,you can log in to the file server. Normally, you will need a NET.CFG file to configure your your card. You can see Netware 386 Installation appendix E for more information about NET.CFG. Below is a sample NET.CFG file: LINK DRIVER IPORTODI port 300 int 5 Frame Ethernet_II Frame Ethernet_802.3 Protocol IPX E0 Ethernet_802.2 : : [6] Packet Driver The driver IPORTPKT.COM is the Packet driver. To load the packet driver , type IPORTPKT 0X60. IPORTPKT syntax: IPORTPKT [-h] [-n] [-d] [-w] [-u] <PACKET_INT_NO> [IRQ] [IO_BASE] where: [-h] Show on-line help. [-n] Convert ETHERNET II header to IEEE 802.3 header. [-d] Do not start LAN card until this driver is called by the higher layer programs first. [-w] Running under Windows environment. [-u] Unload packet driver. <PACKET_INT_NO> This specifies the software interrupt (IRQ) where you'll load the packet driver. It must be in the range 0x60 to 0x80. [IRQ] This specifies the hardware interrupt (IRQ) where your card will be indicated. [IO_BASE] This specifies the I/O address . Example: The following command line loads the Ethernet Packet Driver at software interrupt 60h, at I/O address 300, at hardware interrupt 5. IPORTPKT 0x60 0x5 0x300 or IPORTPKT 0x60 Note: The default I/O address is 300 . Note: The default hardware interrupt is 5 Note: The placement of 0x prior to the parameters. [7] NDIS V2.0 DRIVER FOR OS2 LAN SERVER The Ethernet NDIS2 Driver for IBM OS2 LAN SERVER confirms to the Network Driver Interface Specification(NDIS2). This document shows you how to setup the driver and how to use the enhanced functions by setting the custom keywords in configuration file. Installation by using IBM OS2 LAN SERVER Installation utility: --------------------------------------------------------- Please install the IBM LAN SERVER OS2 driver files following the procedures as described in the following. 1. Install OS/2 Lan Server to HardDisk and install Ethernet adapter in your system properly. 2. In OS/2 window, Click the "MPTS" icon. 3. The screen will display the IBM Logo panel, press "OK". 4. Select "Install" button. 5. Insert the Driver Diskette, specify the driver path A:\OS2 and press <Enter>. 6. When complete above step, then configure your system. 7. The same step as step 4, select "Configure" button. 8. The screen will display "Configure" dialog box and select "LAN adapters and protocols" then press "configure" button. 9. The screen will display "LAPS Configuration" dialog box, move highlight to "BroMax CF Ethernet Card" item in "Network Adapter" window, and select "NetBios" "IEEE802.2" protocol. Press "OK". 10. Installation is complete now. Reset your PC by turning it off and on. Configuration Files: ==================== Sample of configuration file: ----------------------------- File Name: C:\CONFIG.SYS ---------- ... Device=C:\IBMCOM\MACS\CARDGO.OS2 /IRQ 5 /IO 300 Device=C:\IBMCOM\MACS\iPNDIS.OS2 ... CARDGO.OS2 command-line options ------------------------------- /IRQ x x specifies the IRQ /IO yyy yyy specifies the IO Base address File Name: C:\IBMCOM\PROTOCOL.INI ---------- ... [IBMLXCFG] LANDD_nif = LANDD.nif NETBEUI_nif = NETBEUI.nif ODI2NDI_nif = ODI2NDI.nif TCPIP_nif = TCPIP.nif IPORTCF_nif = IPORTCF.nif ... [LANDD_nif] DriverName = LANDD$ Bindings = IPORTCF_nif ETHERAND_TYPE = "I" ... [NETBEUI_nif] DriverName = netbeui$ Bindings = IPORTCF_nif ETHERAND_TYPE = "I" ... [ODI2NDI_nif] DriverName = odi2ndi$ Bindings = IPORTCF_nif ... [TCPIP_nif] DriverName = TCPIP$ Bindings = IPORTCF_nif [IPORTCF_nif] DriverName = iPNDIS$ IRQ = 5 IOBASE = 0x300 Custom Keywords: ---------------- IRQ This keyword is used to set the interrupt of the adapter IOBASE This keyword is used to set the I/O base address of the adapter Important : ============= When using "IBM Netware Requester Support" protocol to connect to Novell server, be sure to fill the parameter(Network Adapter Address) to be the same address as the Ethernet Address of the card. [8] NDIS DRIVER FOR WINDOWS FOR WORKGROUPS 3.11 INSTALLATION A) Install NDIS driver to the WFW 3.11 The drivers named iPNDIS3.386 contained in the directory conform to the Network Driver Interface Specification (NDIS) defined by Microsoft/3Com. NDIS Enhance Mode Driver Installation on Windows for Workgroups -------------------------------------------------- 1. Run Windows by typing WIN from the DOS prompt. 2. Click the "Network" icon in the Main Program Group. 3. Click the "Network Setup" icon from the Network window. 4. Select "Drivers" item from the Network Setup dialog box. 5. Select "Add Adapters" item in the Option dialog box. 6. Select "Unlisted or Updated Network Adapter" when the Install driver field appears. 7. Type destination drive and path name in your PC. Make sure the full path of the directory (i.e. A:\WFW311) is given. 8. Insert CF Ethernet Card Driver Diskette in your floppy drive and press <Enter> to start the installation process. 9. When the "BroMax CF Ethernet Card" dialog box appear, press<Ok> to select the adapter. 10.Follow screen instructions to complete the process. 11.Restart your computer. Sample Configuration Files ====================================================== 1. PROTOCOL.INI File on Windows for Workgroups 3.11 [network.setup] version=0x3110 netcard=BCN0010T,1,BCN0010T,1 transport=ms$nwlinknb,NWLINK transport=ms$ndishlp,MS$NDISHLP transport=ms$netbeui,NETBEUI lana0=BCN0010T,1,ms$nwlinknb lana1=BCN0010T,1,ms$ndishlp lana2=BCN0010T,1,ms$netbeui [protman] DriverName=PROTMAN$ PRIORITY=MS$NDISHLP [NWLINK] BINDINGS=BCN0010T FRAME=ETHERNET_802.2 [MS$NDISHLP] DriverName=ndishlp$ BINDINGS=BCN0010T [NETBEUI] DriverName=netbeui$ SESSIONS=10 NCBS=12 BINDINGS=BCN0010T LANABASE=1 [BCN0010T] DriverName=iPNDIS3$ IRQ=5 IOBASE=0x300 2. To change the IRQ and IOBase setting, edit the PROTOCOL.INI file, and change the IRQ and IOBASE values in [BCN0010T] section. [9] NDIS Driver for LAN Manager Installation Installation Introduction for LAN Manager V2.1 -------------------------------------------------- a. Type "lmsetup" In LanManager Directory. Press Enter. b. Choice "Network Drivers..." in " Configuration ". Press Enter. c. Choice <Add New Configs> ,press Enter. Network Adapter Driver appears. d. Choice <Other Driver> , press Enter. e. Insert the Driver Disk to specified drive (A:\> or B:\>),key in the specified drive (A:\> or B:\>),then push <OK> button. f. Select a available Network Adapter Driver, "BroMax CF Ethernet Card" Push <OK> button. g. Press the SPACEBAR to select the protocol what you want. h. Push <OK> button. Configuration Complete appear. i. Push <Save> button. j. Press "F3" to exit. k. Press Enter. l. Copy "CARDGO.EXE" in Driver Diskette to LanManager Directory. Sample configuration files: [CONFIG.SYS] a.<V2.1> DEVICE=C:\LANMAN.DOS\CARDGO.EXE DEVICE=C:\LANMAN.DOS\DRIVERS\PROTMAN\PROTMAN.DOS /i:C:\LANMAN.DOS DEVICE=C:\LANMAN.DOS\DRIVERS\IPNDIS.DOS [Protocol.ini file for LAN Manager] a. V2.1 [PROTMAN] DRIVERNAME = PROTMAN$ DYNAMIC = YES PRIORITY = NETBEUI [NETBEUI_XIF] Drivername = netbeui$ SESSIONS = 6 NCBS = 12 BINDINGS = "IPORTCF_NIF" LANABASE = 0 [IPORTCF_NIF] ; protocol.ini section for BroMax CF Ethernet Card IOBASE = 0x300 IRQ = 5 DRIVERNAME = IPNDIS$ [Autoexec.bat file for LAN Manager] a. V2.1 @REM ====== LANMAN 2.1 === DO NOT MODIFY BETWEEN THESE LINES SET PATH=C:\LANMAN.DOS\NETPROG;%PATH% NET START WORKSTATION LOAD NETBEUI @REM ====== LANMAN 2.1 === DO NOT MODIFY BETWEEN THESE LINES [10] NDIS 3.1 Driver for Windows 95 Installation INSTALLATION PROCEDURE: 1) Insert CF Ethernet Card into the PCMCIA slot. The system displays the "New Hardware Found" window, with "CF-Ethernet Card" as the device name. 2) Select "Drivers from disk provided by hardware manufacturer" if it is retail version Windows 95 (4.00.950). 3) Insert the driver diskette, then press enter. 4) Occasionally, the system may ask for files from the Windows 95 CD-ROM. Follow the prompt until the installation is complete. 5) Reboot the machine to start the network. [11] NDIS DRIVER FOR WINDOWS 98 INSTALLATION PROCEDURE: 1) Insert CF Ethernet Card into the PCMCIA slot. The system displays the "New Hardware Found" window, with "CF-Ethernet Card" as the device name. 2) Click Next, then select "Search for the best driver for your device.", and click Next to continue. 3) Uncheck the "Microsoft Windows Update". Let Windows 98 search floppy disk drives only. Then insert the driver diskette and click Next. 4) Select the found updated driver, BroMax CF Ethernet Card, then click Next. 5) Occasionally, the system may ask for files from the Windows 98 CD-ROM. Follow the prompt until the installation is complete. 5) Reboot the computer to start the network. [12] NDIS DRIVER FOR WINDOWS NT 3.51 INSTALLATION PROCEDURE: 1) Open the Control Panel, and choose Network Settings. 2) Click the Add Adapter button. 3) Select <Other> Requires disk from manufacturer. 4) Type in the path A:\WINNT 5) Select the "BroMax CF Ethernet Card". 6) Set the IRQ level and I/O Port Address to any free resources, Valid IRQ's=2,3,4,5,6,10,11,12,15. Valid I/O's=240,280,300,320,340,360. 7) Select Bus Type as "PCMCIA". 8) Leave the Bus Number Selected at 0. 9) Click on OK and back to the Network Settings. 10) Click on "Bindings" button. 11) Click on OK and Restart the Machine. [13] NDIS DRIVER FOR WINDOWS NT 4.0 INSTALLATION PROCEDURE: 1) Open the Control Panel, and choose Network 2) Select Adapter tab and click the Add button. 3) Click Have Disk button. 4) Type in the path A:\WINNT 5) Select the "BroMax CF Ethernet Card". 6) Set the IRQ level and I/O Port Address to any free resources, Valid IRQ's=2,3,4,5,6,10,11,12,15. Valid I/O's=240,280,300,320,340,360. 7) Select Bus Type as "PCMCIA". 8) Leave the Bus Number Selected at 0. 9) Click on OK and back to the Network Settings. 10) Click on "Bindings" button. 11) Click on OK and Restart the Machine. [14] NDIS DRIVER FOR WINDOWS 2000 INSTALLATION PROCEDURE: 1) Insert CF Ethernet Card into the PCMCIA slot. The system displays the "Found New Hardware Wizard" window. Clink Next to continue. 2) The "Found New Hardware Wizard" prompt you what do you want the wizard to do. select the "Search for a suitable driver for my device.", and click Next to continue. 3) Check the "Specify a location" while the wizard asking where do you want Windows to search for driver files. Then click Next to continue. 4) Insert the driver disk and specify the path, 'a:\win2000'. then click Next to continue. 5) After the wizard found the INF file and the driver, click Next. 6) When the "Digital Signature Not Found" window pops up, click 'Yes' button to continue installation. 7) After copying the drivers, the wizard shows "Completing the Found New Hardware Wizard", click Finish to close the wizard.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.