Version 03:08:00 10 October 2002 13:34 FIX - prevent W98 lockups when USB device gets PnP STOP message FIX - correction to htmlhelp.h search path for 3.8.0 build FIX - Allow TBCalib to terminate correctly if launched from systray in eeprom mode FIX - Wake up on unmatched liftoff works FIX - Modify tab in DCU now reverts changes if cancel is pressed FIX - Updd clicks works correctly with left button ENH - PortraitAngle can be specified in the registry ENH - WM_UPDDRotateEvent support ENH - allow localisation of post uninstall screens ENH - "Next" key on install license page changed to "Accept" ENH - Support raw data mode for USB devices ENH - USB Macros must be synchronous, this is now enforced in the driver ENH - W2K / XP USB remote wakeup ENH - TBTest grid ENH - TBTest now supports "unlimited" drawing ENH - extended DCU device information ENH - DCU refresh status screen ENH - DCU highlights disconnected devices ENH - Support calibration check to work for hardware calibration ENH - TBApiSendMacroSynchronous implemented ENH - Improved hardware calibration support, ENH - Changed title bar of config to UPDD Draw - Daemon active/inactive ENH - UPDDDraw removed enabled checkbox ENH - UPDDDraw auto-starts daemon if not started ENH - UPDDDraw initial setting is now Stop ENH - UPDDDraw added multiple undo function ENH - Phase two extensions changes ENH - Creates setupsdk3.exe instead of SDKsetup.exe ENH - SDK Integration ENH - Adds support for upddext.chm help file LOC - Title box on w95/nt4 install complete popup dialog translated LOC - extended Japanese support LOC - Japanese translation for "copying files" & "Installing" LOC - Various fixes for minor Japanese support issues OEM - Firmware type detection OEM - Supports oem hardware calibration and diagnostics program TEC - Stlport conversion TEC - Compile error that htmlhelp.h not found TEC - UPDDClicks dlg not included in merged dsp file Version 03:08:02 14 October 2002 12:08 ENH - remove n/a from device grid id column Version 03:08:04 30 October 2002 11:32 FIX - USB device id sometimes showed garbage FIX - Deglitch length values were off by one FIX - support calibration of controllers whilst Initialise option is off FIX - Show correct status data when Initialise option is off FIX - W98 calibration was inaccurate over a dos box ENH - Extended support for eeprom calibration ENH - DLL API ENH - Minor change to DCU devices title ENH - remove n/a from device grid id field OEM - controller id code failed if touching during detect OEM - changes to controller initialisation OEM - correction to firmware linearisation and sensitivity control LOC - Japanese support for TBTest "grid" TEC - STLPort conversion fix to MAKEINF TEC - extra debug option in ISA BUS code Version 03:08:06 20 November 2002 14:39 FIX - system tray icon was not hidden after reboot FIX - UPDDPlay, remove unwanted messages when initialising at same time as driver FIX - correction to handling of empty macros for USB devices FIX - touch immediate mode was not compatible with screen saver / low power video mode FIX - correct IRP issue highlighted by HCT tests FIX - correct IRQL issue highlighted by HCT tests FIX - correct memory leak highlighted by HCT tests FIX - Corrected some multi-bundle install anomalies FIX - USB device id sometimes showed garbage FIX - Memory leak in String class removed ENH - first touch calibration ENH - integration with TBKeyPad 2.4.x ENH - New registry setting InitialMousePortEnabled ENH - include tbapi.dll in release ENH - allows.x 2.4 tbkeypad to install/uninstall correctly in integrated builds ENH - multi-bundle anomalies fixed ENH - change of rotation mode does not reinit driver LOC - localisation support for close button on license dialog TEC - internal spinlock tracking Version 03:08:08 17 December 2002 14:31 FIX - Clone of PnP devices sometimes did not work FIX - Removed garbage in USB "port" display following bad enumeration FIX - Allow connection when a good enumeration follows a bad enumeration FIX - Occasional BSOD in USB when unloading FIX - UPDDPlay missing dll issue corrected FIX - Improved spinlock protection on control arrays (for HCT) FIX - ActiveDraw would not start from system tray FIX - ActiveDraw mode now disabled during calibration FIX - Upddclicks timing corrected FIX - Large morph controls did not work on NT4.0 FIX - Upddplay did not work with legacy code FIX - Don't over write tbkeypad start settings FIX - BSOD if touching USB touchscreen during suspend FIX - Upddplay did not work with legacy macro definition software ENH- Upddclicks better defaults ENH - Upddclicks only gives sound on right clicks ENH - Uninstall removes new keypad files ENH - Reinstalls previous default driver when UPDD is removed ENH - Improvements to uninstall of integrated keypad on NT40 TEC - Handle IRP_MN_QUERY_DEVICE_RELATIONS (for HCT11) TEC - Handle PnP Messages sent to non PnP device object (for HCT11) TEC - Always set status in IRP (for HCT11) TEC - Stlport OEM - Controller redetect if failed becase touching during detect OEM - Control file based versioning OEM - Detection code for new controller model TBA - TBKeyPad integrated release fix Version 03:08:10 30 December 2002 15:05 ENH - new option to disable auto rotation FIX - INF mode install did not unload system tray correctly FIX - setup MAKEINF option wrongly showed detection dialog FIX - systray utility was occasionally crashing after install API - option to unregister all callbacks OEM - Powerpoint version, first cut OEM - remove redundant buttons from toolbar designer Version 03:08:12 10 January 2003 12:22 FIX - calibration termination by escape and timeout did not work correctly FIX - event mode was set to incorrect default at install time FIX - Cancelling calibration would leave values in registry FIX - Corrections to inf installer for clean system ENH - tbmorph allows setting of dialog background colour TEC - Change to tbgenerate OEM - Toolbar definition dialog changes Version 03:08:14 24 January 2003 18:00 FIX - TBApi thread safety improvements (resolve occasional TBSystry crash) FIX - Installing over a different bundle now works ENH - USB now associates with controller based on serial number where present ENH - added tbinf to pass chkinf part of HCT OEM - calibration customisation OEM - new controller firmware support OEM - Powerpoint tailored build Version 03:08:16 28 January 2003 11:28 ENH - restore invertx/y and swap xy settings after failed check calibration Version 03:08:18 28 February 2003 17:29 ENH - Polled ISA BUS access FIX - corrected occasional crash in tbextsvc at shutdown FIX - Corrected error in Firmware macro handling FIX - resolved very occasional crash in tbsystry.exe API - Corrected comments in tbapi.h API - Removed redundant OEM specific API's OEM - Powerpoint specific build OEM - custom initialize routine waits for NT com ports to open OEM - Light pen flash / flood option TEC - new tbvkeymp Version 03:08:20 29 April 2003 18:22 ENH - WHQL LOGO Version 03:08:22 20 April 2003 17:01 ENH - Improvements to UPDDCHECK ENH - Enhanced 4 point calibration ENH - WHQL logo embedded with setup Version 03:08:24 01 June 2003 21:45 ENH - TouchMouse facility ENH - 4 point 20 % calibration ENH - Improved mouse interface performance under CPU load condition TEC - Reinstated release tbsystry TEC - Host case sensitivity in TBA for config data OEM - Powerpoint specific build OEM - Powerpoint specific multi build OEM - Java based client program Version 03:08:26 31 July 2003 16:06 ENH - TBMorph option "Sticky" retains previous dialog position ENH - Show 0 for address / interrupt in serial indirect mode ENH - Reload button on DCU status page ENH - Allow edit of COM port selection for non-standard names ENH - Interlock column in device list is now priority ENH - Check calibration box is now topmost ENH - Calibration area sets limit of touchable area API - new API TBApiSetMorphState API - new API TBApiGetMorphState API - new API TBApiSetDrawState API - new API TBApiGetDrawState OEM - Embedded (un)installer OEM - Java Draw autolaunch implemented TBA - Release does not require sync TBA - Batch mode TBA - XPe integration Version 03:08:28 09 September 2003 12:56 OEM - Dual whiteboard Version 03:08:30 08 October 2003 13:41 OEM - Multi monitor support Version 03:08:32 31 October 2003 13:07 ENH - Win98 Pen 2.0 support FIX - Port on Win98 did not support prefix of "Mouse" FIX - "Sticky" dialogs not enabled by default FIX - "Sticky" dialogs no longer apply TBMorph settings automatically FIX - On localised systems duplicate entries appeared in TBMorph comboboxes FIX - Pressing "Escape" on check calibration dialog applied changes FIX - EEPROM macro did not always execute on calibration timeout FIX - Final EEPROM macro was sometimes called twice asyncronously FIX - TBCalibrate run from the start menu did not revert settings correctly on timeout OEM - Controller status message altered OEM - Icon change OEM - Border calibration allowed duplicate points Version 03:08:34 25 December 2003 10:32 ENH - Interactive touch mode ENH - full build info on about box ENH - Only show bindable events in upddplay dropdowns ENH - UPDDplay RESET events FIX - TBSystry crashed if unable to load icons in system tray TBA - XPe macros were not written TBA - Deglitch fix TBA - Interactive touch TBA - Deglitch was not written to reg file TEC - Timeouts on internal spinlocks OEM - Enhanced controller detection OEM - Pen 2.0 inking overlay Version 03:08:36 25 December 2003 10:32 Version 03:09:00 17 January 2003 16:12Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.