;*********************************************************************** ; ; OEMSETUP.INF ; ; Version : 1.01 (NDIS4) ; ; Olicom network card and driver SETUP INF file. ; ;*********************************************************************** ;----------------------------------------------------------------------- ; OPTION TYPE ; ----------- ; This identifies the Option type we are dealing with. The different ; possible types are: ; ; COMPUTER, DISPLAY, MOUSE, KEYBOARD, LAYOUT, SCSI, PRINTER, ... ; ; Types specific to networking: ; ; NetAdapter, a netcard / adapter combination or just a netcard ; NetDriver, just a netcard driver ; NetTransport, a complete NDIS-compliant TDI transport stack ; NetService, an NT networking service ; NetWork, a complete network ensemble. ; NetProvider a complete network which supports NT MPR protocol ;----------------------------------------------------------------------- [Identification] OptionType = NetAdapter ;----------------------------------------------------------------------- ; PlatformsSupported ; ------------------ ; This identifies the platforms supported by the adapter card. ; Possible types are: ; ; ISA and EISA ;----------------------------------------------------------------------- [PlatformsSupported] ISA EISA PCI [LanguagesSupported] ENG ;----------------------------------------------------------------------- ; OPTION LIST ; ----------- ; This section lists the OEM Option key names. These keys are locale ; independent and used to represent the option in a locale independent ; manner. ; ;----------------------------------------------------------------------- [Options] OCE5X_2327 [OptionsTextENG] OCE5X_2327 = "Olicom RapidFire 2327 Ethernet 10/100 PCI Adapter" [RecBufCountChoices] RB_0 = "8",8 RB_1 = "16",16 RB_2 = "32",32 RB_3 = "48",48 RB_4 = "64",64 [BusNumberChoices] BusNo_1 = "0",0 BusNo_2 = "1",1 BusNo_3 = "2",2 BusNo_4 = "3",3 BusNo_5 = "4",4 BusNo_6 = "5",5 BusNo_7 = "6",6 BusNo_8 = "7",7 BusNo_9 = "8",8 BusNo_10 = "9",9 BusNo_11 = "10",10 [ConnTypeChoices] ConnType_1 = "Auto negotiate",0 ConnType_2 = "100 Mbps Half Duplex",8 ConnType_3 = "100 Mbps Full Duplex",9 ConnType_4 = "10 Mbps Half Duplex",2 ConnType_5 = "10 Mbps Full Duplex",3 [NoYesChoices] NoYes_1 = "No",0 NoYes_2 = "Yes",1 [DisEnahoices] DisEna_1 = "Disable",0 DisEna_2 = "Enable",1 ;----------------------------------------------------------------------- ; Constants for use with dialogs ;----------------------------------------------------------------------- [FileConstants] UtilityInf = "UTILITY.INF" subroutineinf = "SUBROUTN.INF" SoftwareType = "driver" Exit_Code = 0 DialogDllName = "oce5xnd4.dll" HelpfileName = "oce5xnd4.hlp" NetEventDLL = "%SystemRoot%\System32\netevent.dll;%SystemRoot%\System32\Drivers\Oce5xnd4.sys" IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll" Manufacturer = "Olicom" ProductMajorVersion = "1" ProductMinorVersion = "01" ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion) ProductSoftwareName = "OCE5XND4" ProductSoftwareTitle = "Olicom RapidFire Ethernet 10/100 PCI Adapter Driver" ProductSoftwareImagePath = "%SystemRoot%\System32\drivers\oce5xnd4.sys" NetRuleSoftwareType = "oce5xnd4Sys ndisDriver oce5xnd4Driver" NetRuleSoftwareUse = $(SoftwareType) NetRuleSoftwareBindForm = """Oce5xNd4Sys"" yes no container" NetRuleSoftwareClass = {"oce5xnd4Driver basic"} NetRuleSoftwareBindable = {"oce5xnd4Driver oce5xnd4Adapter non exclusive 100"} ProductHardwareName = "OCE5XND4" ProductHardwareOCE5X_2327Title = "Olicom RapidFire 2327 Ethernet 10/100 PCI Adapter" NetRuleHardwareType = "oce5xnd4 oce5xnd4Adapter" NetRuleHardwareBindForm = " yes yes container" NetRuleHardwareClass = {"oce5xnd4Adapter basic"} ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion" ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters" [GeneralConstants] from = "" to = "" ReturnTo = "" ExitCodeOk = 0 ExitCodeCancel = 1 ExitCodeFatal = 2 KeyNull = "" MAXIMUM_ALLOWED = 33554432 RegistryErrorIndex = NO_ERROR KeyProduct = "" KeyParameters = "" TRUE = 1 FALSE = 0 NoTitle = 0 ExitState = "Active" OldVersionExisted = $(FALSE) DriverPath = $(!STF_NTPATH)\drivers PCIDetectSupported = $(TRUE) NT351VersionConstant = "3.51" NT350VersionConstant = "3.50" NT310VersionConstant = "3.10" [FileConstantsENG] ProCaption = "Windows NT Setup" ProCancel = "Cancel" ProCancelMsg = "Windows NT Networking is not correctly installed. "+ "Are you sure you want to cancel copying files?" ProCancelCap = "Network Setup Message" ProText1 = "Copying:" ProText2 = "To:" OCE5X_2327FunctionTitle = "Olicom RapidFire 2327 Ethernet 10/100 PCI Adapter" ProductHardwareOCE5X_2327Description = "Olicom RapidFire 2327 Ethernet 10/100 PCI Adapter" ProductSoftwareDescription = "Olicom RapidFire Ethernet 10/100 PCI NDIS 4.0 Driver" FunctionTitle = $($(Option)FunctionTitle) AdapterType_OCE5X_2327 = 5 CFID_OCE5X_2327 = 1642513 ;; 0x00191011 RecBufCountList = ^(RecBufCountChoices, 1) RecBufCountValues = ^(RecBufCountChoices, 2) ExtPCIList = ^(NoYesChoices, 1) ExtPCIValues = ^(NoYesChoices, 2) ConnTypeList = ^(ConnTypeChoices, 1) ConnTypeValues = ^(ConnTypeChoices, 2) BusNoList = ^(BusNumberChoices, 1) BusNoValues = ^(BusNumberChoices, 2) RecBufCountDefault = 2 ExtPCIDefault = 2 ConnTypeDefault = 1 BusIndexDefault = 1 BusNoDefault = 0 SlotNoDefault = 0 SlotNoUnknown = 1024 [DialogConstantsENG] Help = "&Help" Exit = "Cancel" OK = "OK" HelpContext = "" Continue = "Continue" Cancel = "Cancel" ContextMinimumID = 6000 ContextContentsID = 6000 [date] Now = {} ? $(!LIBHANDLE) GetSystemDate [AskSourceDlgText] DlgText = "Please enter the full path of the Olicom RapidFire Ethernet "+ "Adapter driver setup files. Then choose Continue." ;----------------------------------------------------------------------- ; ADAPTER PARAMETER DIALOG NO. 1 ; ------------------------------ ; This section sets up the adapter parameter dialog. All textstrings ; presented in this dialog are defined here. ; ; OC-2327 Adaptors ; ;----------------------------------------------------------------------- [AdapterParameterDlg1ENG] DlgType = "RadioCombination" DlgTemplate = "OCE5DLG5" Caption = $(FunctionTitle) DlgText = "Please select values for the following fields:" Combo1Label = "&Connection Type:" Combo2Label = "&Receive Buffers:" Combo3Label = "&Extended PCI Commands:" Edit1Label = "&Network Address:" Combo1List = $(ConnTypeList) Combo1Out = $(ConnTypeIndex) Combo2List = $(RecBufCountList) Combo2Out = $(RecBufCountIndex) Combo3List = $(ExtPCIList) Combo3Out = $(ExtPCIIndex) ComboListItemsIn = {Combo1List, Combo2List, Combo3List} ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out} EditTextLim = 19 EditTextIn = $(NetworkAddress) RadioOptionGreyed = {} CBOptionsGreyed = {} NotifyFields = {NO, NO, NO, NO} HelpContext = $(ContextContentsID) ;----------------------------------------------------------------------- ; ADAPTER PARAMETER DIALOG NO. 2 ; ------------------------------ ; This section sets up the adapter parameter dialog. All textstrings ; presented in this dialog are defined here. ; ; OC-2327 Adaptors ; ;----------------------------------------------------------------------- [AdapterParameterDlg2ENG] DlgType = "RadioCombination" DlgTemplate = "OCE5DLG1" Caption = $(FunctionTitle) DlgText = "Please select values for the following fields:" Combo1Label = "&Connection Type:" Combo2Label = "&Receive Buffers:" Combo3Label = "&Extended PCI Commands:" Combo5Label = "&Bus Number:" Edit1Label = "&Network Address:" Combo1List = $(ConnTypeList) Combo1Out = $(ConnTypeIndex) Combo2List = $(RecBufCountList) Combo2Out = $(RecBufCountIndex) Combo3List = $(ExtPCIList) Combo3Out = $(ExtPCIIndex) Combo4List = $(BusNoList) Combo4Out = $(BusNoIndex) ComboListItemsIn = {Combo1List, Combo2List, Combo3List, Combo4List} ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out, Combo4Out} EditTextLim = 19 EditTextIn = $(NetworkAddress) RadioOptionGreyed = {} CBOptionsGreyed = {} NotifyFields = {NO, NO, NO, NO} HelpContext = $(ContextContentsID) ;--------------------------------------------------------------------------- ; 1. Identify ; ; DESCRIPTION: To verify that this INF deals with the same type of options ; as we are choosing currently. ; ; INPUT: None ; ; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL ; $($R1): Option Type (COMPUTER ...) ; $($R2): Diskette description ;--------------------------------------------------------------------------- [Identify] read-syms Identification set Status = STATUS_SUCCESSFUL set Identifier = $(OptionType) set Media = #("Source Media Descriptions", 1, 1) Return $(Status) $(Identifier) $(Media) ;------------------------------------------------------------------------ ; 2. ReturnOptions: ; ; DESCRIPTION: To return the option list supported by this INF and the ; localised text list representing the options. ; ; ; INPUT: $($0): Language used. ( ENG | FRN | ... ) ; ; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL | ; STATUS_NOLANGUAGE ; STATUS_FAILED ; STATUS_NOTSUPPORTED ; ; $($R1): Option List ; $($R2): Option Text List ;------------------------------------------------------------------------ [ReturnOptions] set Status = STATUS_FAILED set OptionList = {} set OptionTextList = {} set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) in $(LanguageList) ifstr(i) $($1) == "" goto returnoptions endif set PlatformList = ^(PlatformsSupported, 1) Ifcontains(i) $($1) in $(PlatformList) goto returnoptions else set Status = STATUS_NOTSUPPORTED goto finish_ReturnOptions endif else set Status = STATUS_NOLANGUAGE goto finish_ReturnOptions endif returnoptions = + set OptionList = ^(Options, 1) set OptionTextList = ^(OptionsText$($0), 1) set Status = STATUS_SUCCESSFUL finish_ReturnOptions = + Return $(Status) $(OptionList) $(OptionTextList) ;------------------------------------------------------------------------ ; ; InstallOption: ; ; This section is shelled to by main installation processing ; or by NCPASHEL.INF during reconfig, removal, update, etc. ; ; ; FUNCTION: To copy files representing Options ; To configure the installed option ; To update the registry for the installed option ; ; INPUT: $($0): Language to use ; $($1): OptionID to install ; $($2): SourceDirectory ; $($3): AddCopy (YES | NO) ; $($4): DoCopy (YES | NO) ; $($5): DoConfig (YES | NO) ; ; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL | ; STATUS_NOLANGUAGE | ; STATUS_USERCANCEL | ; STATUS_FAILED ; ;------------------------------------------------------------------------ [InstallOption] StartWait set SrcDir = "" set Option = $($1) set SrcDir = $($2) set AddCopy = $($3) set DoCopy = $($4) set DoConfig = $($5) ifstr(i) $(SrcDir) == "" Set SrcDir = "A:\" Endif set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) NOT-IN $(LanguageList) Return STATUS_NOLANGUAGE endif Debug-Output "STF_CWDDIR is: "$(!STF_CWDDIR) Debug-Output "STF_LANGUAGE is: "$(!STF_LANGUAGE) set-subst LF = "\n" read-syms GeneralConstants read-syms FileConstants read-syms DialogConstants$(!STF_LANGUAGE) ifstr(i) $(!NTN_Origination) == "NCPA" set Continue = "OK" endif read-syms FileConstants$(!STF_LANGUAGE) detect date set-title $(FunctionTitle) set to = Begin set from = Begin set CommonStatus = STATUS_SUCCESSFUL SetHelpFile $(HelpfileName) 6000 6000 EndWait Begin = + ; ; Get the Windows NT version. We will not install on NT v3.x ; set OSTypeValue = 1536 set CurrentVersionValue = "" OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows Nt\CurrentVersion" $(!REG_KEY_READ) KeyNt Ifstr(i) $(KeyNt) != "" GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue Debug-Output "$(InfFile) $(Option): WinNT CurrentVersion ="$(CurrentVersionValue) CloseRegKey $(KeyNt) Endif ifstr(i) (*($(CurrentVersionValue),4)) == ($(NT351VersionConstant)) Debug-Output "Running on WindowsNT 3.51" set Error = "Windows NT v3.51 is not support by this product" goto fatal endif ifstr(i) (*($(CurrentVersionValue),4)) == ($(NT310VersionConstant)) Debug-Output "Running on WindowsNT 3.10" set Error = "Windows NT v3.10 is not support by this product" goto fatal endif ifstr(i) (*($(CurrentVersionValue),4)) == ($(NT350VersionConstant)) Debug-Output "Running on WindowsNT 3.50" set Error = "Windows NT v3.50 is not support by this product" goto fatal ;; PCI Detect will be included in NT v3.51 ;Debug-Output "Running on WindowsNT 3.50" ;set PCIDetectSupported = $(FALSE) ;set OSTypeValue = 512 endif Ifstr(i) $(!NTN_InstallMode) == deinstall set StartLabel = removeadapter else-Ifstr(i) $(!NTN_InstallMode) == Update set StartLabel = UpgradeSoftware else-Ifstr(i) $(!NTN_InstallMode) == bind set StartLabel = bindingadapter else-Ifstr(i) $(!NTN_InstallMode) == configure set StartLabel = configureadapter Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Debug-Output "Cannot configure the driver software." Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif set Error = $($R0) set from = end set to = end goto nonfatalinfo endif else set StartLabel = installadapter set OEM_ABANDON_OPTIONS = {} set OEM_ABANDON_SOFTWARE = FALSE set OEM_ABANDON_ON = TRUE endif set RecBufCountIndex = *($(RecBufCountList), $(RecBufCountDefault)) set ExtPCIIndex = *($(ExtPCIList), $(ExtPCIDefault)) set ConnTypeIndex = *($(ConnTypeList), $(ConnTypeDefault)) set BusNoIndex = *($(BusNoList), $(BusIndexDefault)) set BusNumber = $(BusNoDefault) set SlotNumber = $(SlotNoDefault) set NetworkAddress = *($(EditTextOut), 1) Shell "" DebugConfiguration "After parameter querying" Shell $(UtilityInf), GetBusTypeNum set BusTypeNum = $($R1) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif Set from = $(fatal) Set to = $(fatal) Goto $(StartLabel) ;----------------------------------------------- ; Installation Section ;----------------------------------------------- ; ; Get the current values of all the parameters ; installadapter = + OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) CloseRegKey $(KeyProduct) ifstr(i) !(NTN_RegBase) == $(ProductKeyName) Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+ $(ProductVersion) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif goto end else Shell $(UtilityInf), CardExistedDlg ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif ifstr(i) $($R1) != "OK" goto end endif set OldVersionExisted = $(TRUE) endif endif Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) install "Install-Dll" Goto adapteroptions ;----------------------------------------------- ; Configuration Section ;----------------------------------------------- ; ; Get the current values of all the parameters ; configureadapter = + Ifstr(i) $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component product key" goto fatalregistry Endif Endif Debug-Output "INF: Shelling to FindService" Shell $(UtilityInf) FindService, $(KeyProduct) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "INF: FindService shell failure" Goto ShellCodeError Endif Ifstr(i) $($R0) != NO_ERROR Debug-Output "INF: FindService Shell error: "$($R0) Goto fatalregistry endif Set KeyParameters = $($R2) CloseRegKey $($R1) Ifstr $(KeyParameters) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component service" goto fatalregistry endif set OldVersionExisted = $(TRUE) set ValueName = "" set ValueData = "" set ValueStr = "" set ValueList = {} EnumRegValue $(KeyParameters) ValueList ForListDo $(ValueList) set ValueItem = $($) set ValueName = *($(ValueItem),1) set ValueData = *($(ValueItem),4) ifstr(i) $(ValueName) == "ReceiveBuffers" set RecBufCountValue = $(ValueData) else-ifstr(i) $(ValueName) == "ExtendedPCI" set ExtPCIValue = $(ValueData) else-ifstr(i) $(ValueName) == "ConnectionType" set ConnTypeValue = $(ValueData) else-ifstr(i) $(ValueName) == "BusNumber" set BusNoValue = $(ValueData) else-ifstr(i) $(ValueName) == "SlotNumber" set SlotNumber = $(ValueData) else-ifstr(i) $(ValueName) == "NetworkAddress" set NetworkAddress = $(ValueData) endif EndForListDo ; ; Combo-lists and radio-buttons use a special list of parameter-names ; when dialogs are executed. The following section converts the actual ; values into the corresponding names (indexes). If a value is undefined, ; the first entry in the index-list is used. ; set RecBufCountIndex = *($(RecBufCountList), ~($(RecBufCountValues),$(RecBufCountValue))) ifstr(i) $(RecBufCountIndex) == "" set RecBufCountIndex = *($(RecBufCountList), RecBufCountDefault) endif set ExtPCIIndex = *($(ExtPCIList), ~($(ExtPCIValues),$(ExtPCIValue))) ifstr(i) $(ExtPCIIndex) == "" set ExtPCIIndex = *($(ExtPCIList), ExtPCIDefault) endif set ConnTypeIndex = *($(ConnTypeList), ~($(ConnTypeValues),$(ConnTypeValue))) ifstr(i) $(ConnTypeIndex) == "" set ConnTypeIndex = *($(ConnTypeList), ConnTypeDefault) endif set BusNoIndex = *($(BusNoList), ~($(BusNoValues),$(BusNoValue))) ifstr(i) $(BusNoIndex) == "" set BusNoIndex = *($(BusNoList), BusIndexDefault) endif ; adapteroptions = + set from = adapteroptions ifstr(i) $(!NTN_InstallMode) == "install" ; ; User will NOT be asked to change/verify configuration during ; normal or unattended installation, unless we are installing on ; NT v3.50. ; ifint $(PCIDetectSupported) == $(TRUE) ; We will not ask user for configuration during installation ; if PCI detection is supported goto unattended endif ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" ; Default parameters for unattended installation goto unattended endif endif set OldNetAddress = $(NetworkAddress) ; ; Load DLL containing dialogs and verification routines ; LoadLibrary "Olicom Ethernet Driver Disk" $(DialogDllName) DialogHandle ; ; Read main dialog setup and show dialog ; ifint $(PCIDetectSupported) == $(FALSE) read-syms AdapterParameterDlg2$(!STF_LANGUAGE) else read-syms AdapterParameterDlg1$(!STF_LANGUAGE) endif ui start "InputDlg" $(DialogHandle) ifstr(i) $(DLGEVENT) == "CONTINUE" ; ; parameters have already been stored at this stage ; ; ; Save new settings because this dialog might be called again. ; If CANCEL was pressed these values will not be used ; set ConnTypeIndex = $(Combo1Out) set RecBufCountIndex = $(Combo2Out) set ExtPCIIndex = $(Combo3Out) ifint $(PCIDetectSupported) == $(FALSE) set BusNoIndex = $(Combo5Out) endif set NetworkAddress = *($(EditTextOut),1) ui pop 1 goto nextstep else-ifstr(i) $(DLGEVENT) == "EXIT" set CommonStatus = STATUS_USERCANCEL Debug-Output "Action: exit. Bye." ui pop 1 FreeLibrary $(DialogHandle) goto end else ui pop 1 Debug-Output "Action: unknown: "$(DLGEVENT) FreeLibrary $(DialogHandle) goto end endif nextstep =+ ifstr $(NetworkAddress) != "" ; ; If network address has been entered then verify that it is a ; valid address (not a multicast or broadcast address) ; set FLibraryErrCtl = 1 LibraryProcedure DlgResult $(DialogHandle) VerifyEthAddress $(NetworkAddress) set FLibraryErrCtl = 0 ifstr $(DlgResult) != "STATUS_SUCCESS" FreeLibrary $(DialogHandle) set Error = $(DlgResult) goto nonfatal endif endif FreeLibrary $(DialogHandle) unattended =+ ifint $(OldVersionExisted) == $(TRUE) ifstr(i) $(!NTN_InstallMode) == configure goto writeparameters endif endif StartWait Ifint $(OldVersionExisted) != $(FALSE) Goto installhardware Endif ifstr(i) $(!NTN_InstallMode) == "install" Ifstr(i) $(DoCopy) == "YES" Ifstr(i) $(SrcDir) == "" read-syms AskSourceDlgText Shell $(subroutineinf) DoAskSourceEx $(SrcDir) $(DlgText) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) Endif Endif install "Install-Option" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal endif endif ; ; Insert hardware component in registry ; installhardware =+ ifint $(PCIDetectSupported) == $(FALSE) ifstr(i) $(!AutoNetInterfaceType) != "" set BusTypeNum = $(!AutoNetInterfaceType) else set BusTypeNum = 5 endif ifstr(i) $(!AutoNetBusNumber) != "" set BusNumber = $(!AutoNetBusNumber) else set BusNumber = $(BusNoDefault) endif Set InstalledAdapter = "NO" else ; ; If We are installing a PCI adapter so go search PCI bus ; for our adapter ; set BusTypeNum = 5 set VendorID = 4113 ; Vendor ID: 1011h set DeviceID = 25 ; Device ID: 19h ; Flag adapter already installed Set InstalledAdapter = "YES" ; Get PCI information Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(DeviceID) set AdapterList = $($R0) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R0) == {} ; ; Adapter list is empty. No adapter of this type was found ; else ; ; Adapter(s) has been found. We will try to find out if the (or ; these) adapter hasn't been installed already. ; ForListDo $(AdapterList) ; Run through the Adapter list ; Get Bus number from list: set TestBusNumber = *($($),1) ; Get SLot Number from list: set TestSlotNumber = *($($),2) ; Check registry Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(TestBusNumber), + $(TestSlotNumber), $(ProductHardware$(Option)Description), + $(ProductHardwareName), "NO" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr $($R0) != "NO_ERROR" set Error = $($R0) goto fatal endif ifstr(i) $($R1) == "NO" ; This adapter in the AdapterList has not been install yet ifstr(i) $(InstalledAdapter) == "YES" ; We have found an Adapter for which our driver ; has not been installed. Check if other drivers has ; been installed for this Adapter. ; Check registry ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" ; We will do no further check in unattended install Set InstalledAdapter = "NO" set DetectedBusNumber = $(TestBusNumber) set DetectedSlotNumber = $(TestSlotNumber) Debug-Output "$(InfFile) $(Option): Installing Card at $(DetectedBusNumber):$(DetectedSlotNumber)!" else Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(TestBusNumber), + $(TestSlotNumber), $(ProductHardware$(Option)Description), + $(ProductHardwareName), "YES" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr $($R0) != "NO_ERROR" set Error = $($R0) goto fatal endif ifstr(i) $($R1) == "NO" ; We have found an Adapter with no other installed ; drivers. Lets install. ; We can not Break from ForListDo, so we will ; just flag that we have found an adapter to install Set InstalledAdapter = "NO" set DetectedBusNumber = $(TestBusNumber) set DetectedSlotNumber = $(TestSlotNumber) else Debug-Output "$(InfFile) $(Option): Card Already at $(TestBusNumber):$(TestSlotNumber) already installed!" set Error = "An adapter at "$(TestBusNumber)":"$(TestSlotNumber)" (Bus : Slot) is already "+ "installed with a non Olicom RapidFire Ethernet 10/100 driver. Install anyway?" Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), WARNING, $(Error) ifstr(i) $($R0) != STATUS_SUCCESSFUL set Error = $($R0) goto fatal endif ifstr(i) $($R1) == "OK" Set InstalledAdapter = "NO" set DetectedBusNumber = $(TestBusNumber) set DetectedSlotNumber = $(TestSlotNumber) endif endif endif endif endif EndForListDo endif Set BusNumber = $(DetectedBusNumber) Set SlotNumber = $(DetectedSlotNumber) endif ifstr(i) $(InstalledAdapter) == "YES" ; We had no adapter to install. Exit set Error = "Network card is not present in the system"+ "or network card already installed" set CommonStatus = USER_CANCEL set from = end goto nonfatal endif ; ; Install this adapter ; Debug-Output "$(InfFile) $(Option): Installing Card at $(BusNumber):$(SlotNumber)!" set ReturnTo = ComponentsHasBeenAdded goto AddAdapterComponents ComponentsHasBeenAdded =+ Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName) ifint $($R4) != -1 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)) endif ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "Cannot add hardware component" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add hardware component" CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) goto fatalregistry endif set KeyProduct = $($R1) set KeyAdapterRules = $($R2) set KeyParameters = $($R3) set AdapterNumber = $($R4) ; ifint $(PCIDetectSupported) == $(FALSE) set ThisProductTitle = "["$($R4)"] "$(ProductHardware$(Option)Title) ; else ; set ThisProductTitle = "["$($R4)"] "$(ProductHardware$(Option)Title)" ("$(BusNumber)":"$(SlotNumber)")" ; endif set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+ {Title,$(NoTitle),$(!REG_VT_SZ),$(ThisProductTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+ {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif CloseRegKey $(KeyProduct) Set KeyProduct = "" set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)"""" set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm) set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+ {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif CloseRegKey $(KeyAdapterRules) set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add value list." CloseRegKey $(KeyParameters) goto fatalregistry endif ; ; Write Adapter Parameters to registry ; writeparameters = + Ifstr(i) $(KeyParameters) == $(KeyNull) Debug-Output "*** KeyParameters is NULL at writeparameters" Endif ; ; Convert selections from combo-lists and radio-buttons into actual ; parameter values ; set RecBufCountValue = *($(RecBufCountValues), ~($(RecBufCountList),$(RecBufCountIndex))) set ExtPCIValue = *($(ExtPCIValues), ~($(ExtPCIList),$(ExtPCIIndex))) set ConnTypeValue = *($(ConnTypeValues), ~($(ConnTypeList),$(ConnTypeIndex))) ifstr(i) $(!NTN_InstallMode) != "install" set BusNumber = *($(BusNoValues), ~($(BusNoList),$(BusNoIndex))) endif ; ; Set up parameter list for AddValueList routine ; set NewValueList = {{AdapterCFID,$(NoTitle),$(!REG_VT_DWORD),$(CFID_$(Option))},+ {AdapterType,$(NoTitle),$(!REG_VT_DWORD),$(AdapterType_$(Option))},+ {OSType,$(NoTitle),$(!REG_VT_DWORD),$(OSTypeValue)},+ {MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+ {BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+ {BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+ {ReceiveBuffers,$(NoTitle),$(!REG_VT_DWORD),$(RecBufCountValue)},+ {ExtendedPCI,$(NoTitle),$(!REG_VT_DWORD),$(ExtPCIValue)},+ {ConnectionType,$(NoTitle),$(!REG_VT_DWORD),$(ConnTypeValue)}} ifstr $(NetworkAddress) != "" set NewValueList = >($(NewValueList),{NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)}) endif ifint $(PCIDetectSupported) == $(TRUE) set NewValueList = >($(NewValueList),{SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(SlotNumber)}) endif ;--------------------------------------- ; Add keyword to prevent driver from ; entering promiscuous mode ; ;set NewValueList = >($(NewValueList),{AllowTrace,$(NoTitle),$(!REG_VT_DWORD),0}) ; ; Now update registry ; Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList) ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" Shell $(UtilityInf),AddDefaultNetCardParameters,$(KeyParameters) endif ; ; If the network address has been deleted then also delete it from ; the registry. ; ifstr $(OldNetAddress) != "" ifstr $(NetworkAddress) == "" DeleteRegValue $(KeyParameters) NetworkAddress endif endif CloseRegKey $(KeyParameters) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "Registry error: Add value list" goto fatalregistry endif EndWait goto successful bindingadapter =+ set Error = "Binding: Sorry, not yet implemented." goto fatal ;----------------------------------------------- ; Add Software component to registry ;----------------------------------------------- ; ; AddAdapterComponents =+ ifint $(OldVersionExisted) == $(TRUE) goto $(ReturnTo) endif Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), + $(ProductSoftwareName), + $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), + $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+ $(NetEventDLL), "" Set OEM_ABANDON_SOFTWARE = TRUE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "OEMNADUB.INF: Registry error: add software components" CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) goto fatalregistry endif set SoftProductKey = $($R1) Set SoftNetRuleKey = $($R2) Set SoftServiceKey = $($R3) Set SoftParameterKey = $($R4) Set SoftLinkageKey = $($R5) set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+ {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+ {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+ {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add value list." CloseRegKey $(SoftProductKey) CloseRegKey $(SoftNetRuleKey) CloseRegKey $(SoftServiceKey) CloseRegKey $(SoftParameterKey) CloseRegKey $(SoftLinkageKey) goto fatalregistry endif set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+ {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, + {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, + {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) CloseRegKey $(SoftProductKey) CloseRegKey $(SoftNetRuleKey) CloseRegKey $(SoftServiceKey) CloseRegKey $(SoftParameterKey) CloseRegKey $(SoftLinkageKey) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add value list." goto fatalregistry endif set OldVersionExisted = $(TRUE) goto $(ReturnTo) ;----------------------------------------------- ; Remove Adapter Section ;----------------------------------------------- ; ; Remove all adapter information from the registry ; removeadapter = + Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif else Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $(!NTN_RegBase) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end UpgradeSoftware = + OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set !UG_Filename = $($R0) install "Install-Update" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS goto fatal endif SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)} SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)} CloseRegKey $(KeyProduct) else goto fatalregistry endif goto end successful = + goto end abandon = + ForListDo $(OEM_ABANDON_OPTIONS) Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $($) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif EndForListDo Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), FALSE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end warning = + Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(to) else-ifstr(i) $($R1) == "CANCEL" goto $(from) else goto "end" endif nonfatalinfo = + Set Severity = STATUS Set CommonStatus = STATUS_USERCANCEL goto nonfatalmsg nonfatal = + Set Severity = NONFATAL goto nonfatalmsg nonfatalmsg = + ifstr(i) $(Error) == "" Set Severity = NONFATAL Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(from) else goto "end" endif fatalregistry = + Shell "subroutn.inf" SetupMessage $(!STF_LANGUAGE) WARNING "Fatal Error" Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal fatal = + ifstr(i) $(Error) == "" Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto setfailed ShellCodeError = + set DlgType = "MessageBox" set STF_MB_TITLE = "Error: "$(FunctionTitle) set STF_MB_TEXT = "Shell Code Error" set STF_MB_TYPE = 1 set STF_MB_ICON = 3 set STF_MB_DEF = 1 ui start "Error Message" goto setfailed setfailed = + set CommonStatus = STATUS_FAILED ifstr(i) $(OEM_ABANDON_ON) == TRUE set OEM_ABANDON_ON = FALSE goto abandon endif goto end end = + goto term term = + Return $(CommonStatus) [Install-Option] set STF_VITAL = "" ifstr(i) $(AddCopy) == "YES" AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers endif Debug-Output "OEMSETUP.INF: [Install-Option] DoCopy = "$(DoCopy) ifstr(i) $(DoCopy) == "YES" set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList endif Exit [Install-Update] set STF_VITAL = "" set STF_OVERWRITE = "VERIFYSOURCEOLDER" AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH) AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exit [Install-Dll] set STF_VITAL = "" ifstr(i) $(AddCopy) == "YES" AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH) endif ifstr(i) $(DoCopy) == "YES" set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList else ; get minimum needed files for configuration LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\OCE5XND4.DLL $(!STF_WINDOWSSYSPATH)\OCE5XND4.DLL LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\OCE5XND4.HLP $(!STF_WINDOWSSYSPATH)\OCE5XND4.HLP endif exit [Source Media Descriptions] 1 = "RapidFire 2327 Ethernet 10/100 PCI Adapter Driver Disk" [ProductType] STF_PRODUCT = Winnt STF_PLATFORM = I386 [Files-Inf] 1, oemsetup.inf, SIZE=999, RENAME=$(!UG_Filename) [Files-OCE5X_2327] 1, OCE5XND4.SYS, SIZE=999 [Files-Dll] 1, oce5xnd4.dll, SIZE=999 1, oce5xnd4.hlp, SIZE=999 [Files-dummy]Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.