;***********************************************************************
;
; OEMSETUP.INF
;
; Version : 1.01
;
; Olicom network card and driver SETUP INF file.
;
;***********************************************************************
;-----------------------------------------------------------------------
; OPTION TYPE
; -----------
; This identifies the Option type we are dealing with. The different
; possible types are:
;
; COMPUTER, DISPLAY, MOUSE, KEYBOARD, LAYOUT, SCSI, PRINTER, ...
;
; Types specific to networking:
;
; NetAdapter, a netcard / adapter combination or just a netcard
; NetDriver, just a netcard driver
; NetTransport, a complete NDIS-compliant TDI transport stack
; NetService, an NT networking service
; NetWork, a complete network ensemble.
; NetProvider a complete network which supports NT MPR protocol
;-----------------------------------------------------------------------
[Identification]
OptionType = NetAdapter
;-----------------------------------------------------------------------
; PlatformsSupported
; ------------------
; This identifies the platforms supported by the adapter card.
; Possible types are:
;
; ISA and EISA
;-----------------------------------------------------------------------
[PlatformsSupported]
ISA
EISA
PCI
[LanguagesSupported]
ENG
;-----------------------------------------------------------------------
; OPTION LIST
; -----------
; This section lists the OEM Option key names. These keys are locale
; independent and used to represent the option in a locale independent
; manner.
;
;-----------------------------------------------------------------------
[Options]
OCE5X_2327
[OptionsTextENG]
OCE5X_2327 = "Olicom RapidFire 2327 Ethernet 10/100 PCI Adapter"
[RecBufCountChoices]
RB_0 = "8",8
RB_1 = "16",16
RB_2 = "32",32
RB_3 = "48",48
RB_4 = "64",64
[BusNumberChoices]
BusNo_1 = "0",0
BusNo_2 = "1",1
BusNo_3 = "2",2
BusNo_4 = "3",3
BusNo_5 = "4",4
BusNo_6 = "5",5
BusNo_7 = "6",6
BusNo_8 = "7",7
BusNo_9 = "8",8
BusNo_10 = "9",9
BusNo_11 = "10",10
[ConnTypeChoices]
ConnType_1 = "Auto negotiate",0
ConnType_2 = "100 Mbps Half Duplex",8
ConnType_3 = "100 Mbps Full Duplex",9
ConnType_4 = "10 Mbps Half Duplex",2
ConnType_5 = "10 Mbps Full Duplex",3
[NoYesChoices]
NoYes_1 = "No",0
NoYes_2 = "Yes",1
[DisEnahoices]
DisEna_1 = "Disable",0
DisEna_2 = "Enable",1
;-----------------------------------------------------------------------
; Constants for use with dialogs
;-----------------------------------------------------------------------
[FileConstants]
UtilityInf = "UTILITY.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
DialogDllName = "oce5xnd3.dll"
HelpfileName = "oce5xnd3.hlp"
NetEventDLL = "%SystemRoot%\System32\netevent.dll;%SystemRoot%\System32\Drivers\Oce5xnd3.sys"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
Manufacturer = "Olicom"
ProductMajorVersion = "1"
ProductMinorVersion = "01"
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
ProductSoftwareName = "OCE5XND3"
ProductSoftwareTitle = "Olicom RapidFire Ethernet 10/100 PCI Adapter Driver"
ProductSoftwareImagePath = "%SystemRoot%\System32\drivers\oce5xnd3.sys"
NetRuleSoftwareType = "oce5xnd3Sys ndisDriver oce5xnd3Driver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """Oce5xNd3Sys"" yes no container"
NetRuleSoftwareClass = {"oce5xnd3Driver basic"}
NetRuleSoftwareBindable = {"oce5xnd3Driver oce5xnd3Adapter non exclusive 100"}
ProductHardwareName = "OCE5XND3"
ProductHardwareOCE5X_2327Title = "Olicom RapidFire 2327 Ethernet 10/100 PCI Adapter"
NetRuleHardwareType = "oce5xnd3 oce5xnd3Adapter"
NetRuleHardwareBindForm = " yes yes container"
NetRuleHardwareClass = {"oce5xnd3Adapter basic"}
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
[GeneralConstants]
from = ""
to = ""
ReturnTo = ""
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
PCIDetectSupported = $(TRUE)
NT350VersionConstant = "3.50"
NT310VersionConstant = "3.10"
[FileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. "+
"Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
OCE5X_2327FunctionTitle = "Olicom RapidFire 2327 Ethernet 10/100 PCI Adapter"
ProductHardwareOCE5X_2327Description = "Olicom RapidFire 2327 Ethernet 10/100 PCI Adapter"
ProductSoftwareDescription = "Olicom RapidFire Ethernet 10/100 PCI Adapter Driver"
FunctionTitle = $($(Option)FunctionTitle)
AdapterType_OCE5X_2327 = 5
CFID_OCE5X_2327 = 1642513 ;; 0x00191011
RecBufCountList = ^(RecBufCountChoices, 1)
RecBufCountValues = ^(RecBufCountChoices, 2)
ExtPCIList = ^(NoYesChoices, 1)
ExtPCIValues = ^(NoYesChoices, 2)
ConnTypeList = ^(ConnTypeChoices, 1)
ConnTypeValues = ^(ConnTypeChoices, 2)
BusNoList = ^(BusNumberChoices, 1)
BusNoValues = ^(BusNumberChoices, 2)
RecBufCountDefault = 2
ExtPCIDefault = 2
ConnTypeDefault = 1
BusIndexDefault = 1
BusNoDefault = 0
SlotNoDefault = 0
SlotNoUnknown = 1024
[DialogConstantsENG]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"
ContextMinimumID = 6000
ContextContentsID = 6000
[date]
Now = {} ? $(!LIBHANDLE) GetSystemDate
[AskSourceDlgText]
DlgText = "Please enter the full path of the Olicom RapidFire Ethernet "+
"Adapter driver setup files. Then choose Continue."
;-----------------------------------------------------------------------
; ADAPTER PARAMETER DIALOG NO. 1
; ------------------------------
; This section sets up the adapter parameter dialog. All textstrings
; presented in this dialog are defined here.
;
; OC-2327 Adaptors
;
;-----------------------------------------------------------------------
[AdapterParameterDlg1ENG]
DlgType = "RadioCombination"
DlgTemplate = "OCE5DLG5"
Caption = $(FunctionTitle)
DlgText = "Please select values for the following fields:"
Combo1Label = "&Connection Type:"
Combo2Label = "&Receive Buffers:"
Combo3Label = "&Extended PCI Commands:"
Edit1Label = "&Network Address:"
Combo1List = $(ConnTypeList)
Combo1Out = $(ConnTypeIndex)
Combo2List = $(RecBufCountList)
Combo2Out = $(RecBufCountIndex)
Combo3List = $(ExtPCIList)
Combo3Out = $(ExtPCIIndex)
ComboListItemsIn = {Combo1List, Combo2List, Combo3List}
ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out}
EditTextLim = 19
EditTextIn = $(NetworkAddress)
RadioOptionGreyed = {}
CBOptionsGreyed = {}
NotifyFields = {NO, NO, NO, NO}
HelpContext = $(ContextContentsID)
;-----------------------------------------------------------------------
; ADAPTER PARAMETER DIALOG NO. 2
; ------------------------------
; This section sets up the adapter parameter dialog. All textstrings
; presented in this dialog are defined here.
;
; OC-2327 Adaptors
;
;-----------------------------------------------------------------------
[AdapterParameterDlg2ENG]
DlgType = "RadioCombination"
DlgTemplate = "OCE5DLG1"
Caption = $(FunctionTitle)
DlgText = "Please select values for the following fields:"
Combo1Label = "&Connection Type:"
Combo2Label = "&Receive Buffers:"
Combo3Label = "&Extended PCI Commands:"
Combo5Label = "&Bus Number:"
Edit1Label = "&Network Address:"
Combo1List = $(ConnTypeList)
Combo1Out = $(ConnTypeIndex)
Combo2List = $(RecBufCountList)
Combo2Out = $(RecBufCountIndex)
Combo3List = $(ExtPCIList)
Combo3Out = $(ExtPCIIndex)
Combo4List = $(BusNoList)
Combo4Out = $(BusNoIndex)
ComboListItemsIn = {Combo1List, Combo2List, Combo3List, Combo4List}
ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out, Combo4Out}
EditTextLim = 19
EditTextIn = $(NetworkAddress)
RadioOptionGreyed = {}
CBOptionsGreyed = {}
NotifyFields = {NO, NO, NO, NO}
HelpContext = $(ContextContentsID)
;---------------------------------------------------------------------------
; 1. Identify
;
; DESCRIPTION: To verify that this INF deals with the same type of options
; as we are choosing currently.
;
; INPUT: None
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL
; $($R1): Option Type (COMPUTER ...)
; $($R2): Diskette description
;---------------------------------------------------------------------------
[Identify]
read-syms Identification
set Status = STATUS_SUCCESSFUL
set Identifier = $(OptionType)
set Media = #("Source Media Descriptions", 1, 1)
Return $(Status) $(Identifier) $(Media)
;------------------------------------------------------------------------
; 2. ReturnOptions:
;
; DESCRIPTION: To return the option list supported by this INF and the
; localised text list representing the options.
;
;
; INPUT: $($0): Language used. ( ENG | FRN | ... )
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL |
; STATUS_NOLANGUAGE
; STATUS_FAILED
; STATUS_NOTSUPPORTED
;
; $($R1): Option List
; $($R2): Option Text List
;------------------------------------------------------------------------
[ReturnOptions]
set Status = STATUS_FAILED
set OptionList = {}
set OptionTextList = {}
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) in $(LanguageList)
ifstr(i) $($1) == ""
goto returnoptions
endif
set PlatformList = ^(PlatformsSupported, 1)
Ifcontains(i) $($1) in $(PlatformList)
goto returnoptions
else
set Status = STATUS_NOTSUPPORTED
goto finish_ReturnOptions
endif
else
set Status = STATUS_NOLANGUAGE
goto finish_ReturnOptions
endif
returnoptions = +
set OptionList = ^(Options, 1)
set OptionTextList = ^(OptionsText$($0), 1)
set Status = STATUS_SUCCESSFUL
finish_ReturnOptions = +
Return $(Status) $(OptionList) $(OptionTextList)
;------------------------------------------------------------------------
;
; InstallOption:
;
; This section is shelled to by main installation processing
; or by NCPASHEL.INF during reconfig, removal, update, etc.
;
;
; FUNCTION: To copy files representing Options
; To configure the installed option
; To update the registry for the installed option
;
; INPUT: $($0): Language to use
; $($1): OptionID to install
; $($2): SourceDirectory
; $($3): AddCopy (YES | NO)
; $($4): DoCopy (YES | NO)
; $($5): DoConfig (YES | NO)
;
; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL |
; STATUS_NOLANGUAGE |
; STATUS_USERCANCEL |
; STATUS_FAILED
;
;------------------------------------------------------------------------
[InstallOption]
StartWait
set SrcDir = ""
set Option = $($1)
set SrcDir = $($2)
set AddCopy = $($3)
set DoCopy = $($4)
set DoConfig = $($5)
ifstr(i) $(SrcDir) == ""
Set SrcDir = "A:\"
Endif
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) NOT-IN $(LanguageList)
Return STATUS_NOLANGUAGE
endif
Debug-Output "STF_CWDDIR is: "$(!STF_CWDDIR)
Debug-Output "STF_LANGUAGE is: "$(!STF_LANGUAGE)
set-subst LF = "\n"
read-syms GeneralConstants
read-syms FileConstants
read-syms DialogConstants$(!STF_LANGUAGE)
ifstr(i) $(!NTN_Origination) == "NCPA"
set Continue = "OK"
endif
read-syms FileConstants$(!STF_LANGUAGE)
detect date
set-title $(FunctionTitle)
set to = Begin
set from = Begin
set CommonStatus = STATUS_SUCCESSFUL
SetHelpFile $(HelpfileName) 6000 6000
EndWait
Begin = +
;
; Get the Windows NT version. We will not install on NT v3.1x
;
set OSTypeValue = 1536
set CurrentVersionValue = ""
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows Nt\CurrentVersion" $(!REG_KEY_READ) KeyNt
Ifstr(i) $(KeyNt) != ""
GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue
Debug-Output "$(InfFile) $(Option): WinNT CurrentVersion ="$(CurrentVersionValue)
CloseRegKey $(KeyNt)
Endif
ifstr(i) (*($(CurrentVersionValue),4)) == ($(NT310VersionConstant))
Debug-Output "Running on WindowsNT 3.10"
set Error = "Windows NT v3.10 is not support by this product"
goto fatal
endif
ifstr(i) (*($(CurrentVersionValue),4)) == ($(NT350VersionConstant))
Debug-Output "Running on WindowsNT 3.50"
set Error = "Windows NT v3.50 is not support by this product"
goto fatal
;; PCI Detect will be included in NT v3.51
;Debug-Output "Running on WindowsNT 3.50"
;set PCIDetectSupported = $(FALSE)
;set OSTypeValue = 512
endif
Ifstr(i) $(!NTN_InstallMode) == deinstall
set StartLabel = removeadapter
else-Ifstr(i) $(!NTN_InstallMode) == Update
set StartLabel = UpgradeSoftware
else-Ifstr(i) $(!NTN_InstallMode) == bind
set StartLabel = bindingadapter
else-Ifstr(i) $(!NTN_InstallMode) == configure
set StartLabel = configureadapter
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Debug-Output "Cannot configure the driver software."
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
endif
else
set StartLabel = installadapter
set OEM_ABANDON_OPTIONS = {}
set OEM_ABANDON_SOFTWARE = FALSE
set OEM_ABANDON_ON = TRUE
endif
set RecBufCountIndex = *($(RecBufCountList), $(RecBufCountDefault))
set ExtPCIIndex = *($(ExtPCIList), $(ExtPCIDefault))
set ConnTypeIndex = *($(ConnTypeList), $(ConnTypeDefault))
set BusNoIndex = *($(BusNoList), $(BusIndexDefault))
set BusNumber = $(BusNoDefault)
set SlotNumber = $(SlotNoDefault)
set NetworkAddress = *($(EditTextOut), 1)
Shell "" DebugConfiguration "After parameter querying"
Shell $(UtilityInf), GetBusTypeNum
set BusTypeNum = $($R1)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
Set from = $(fatal)
Set to = $(fatal)
Goto $(StartLabel)
;-----------------------------------------------
; Installation Section
;-----------------------------------------------
;
; Get the current values of all the parameters
;
installadapter = +
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
CloseRegKey $(KeyProduct)
ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
$(ProductVersion)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
goto end
else
Shell $(UtilityInf), CardExistedDlg
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
ifstr(i) $($R1) != "OK"
goto end
endif
set OldVersionExisted = $(TRUE)
endif
endif
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
install "Install-Dll"
Goto adapteroptions
;-----------------------------------------------
; Configuration Section
;-----------------------------------------------
;
; Get the current values of all the parameters
;
configureadapter = +
Ifstr(i) $(KeyProduct) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Debug-Output "Cannot find component product key"
goto fatalregistry
Endif
Endif
Debug-Output "INF: Shelling to FindService"
Shell $(UtilityInf) FindService, $(KeyProduct)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "INF: FindService shell failure"
Goto ShellCodeError
Endif
Ifstr(i) $($R0) != NO_ERROR
Debug-Output "INF: FindService Shell error: "$($R0)
Goto fatalregistry
endif
Set KeyParameters = $($R2)
CloseRegKey $($R1)
Ifstr $(KeyParameters) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Debug-Output "Cannot find component service"
goto fatalregistry
endif
set OldVersionExisted = $(TRUE)
set ValueName = ""
set ValueData = ""
set ValueStr = ""
set ValueList = {}
EnumRegValue $(KeyParameters) ValueList
ForListDo $(ValueList)
set ValueItem = $($)
set ValueName = *($(ValueItem),1)
set ValueData = *($(ValueItem),4)
ifstr(i) $(ValueName) == "ReceiveBuffers"
set RecBufCountValue = $(ValueData)
else-ifstr(i) $(ValueName) == "ExtendedPCI"
set ExtPCIValue = $(ValueData)
else-ifstr(i) $(ValueName) == "ConnectionType"
set ConnTypeValue = $(ValueData)
else-ifstr(i) $(ValueName) == "BusNumber"
set BusNoValue = $(ValueData)
else-ifstr(i) $(ValueName) == "SlotNumber"
set SlotNumber = $(ValueData)
else-ifstr(i) $(ValueName) == "NetworkAddress"
set NetworkAddress = $(ValueData)
endif
EndForListDo
;
; Combo-lists and radio-buttons use a special list of parameter-names
; when dialogs are executed. The following section converts the actual
; values into the corresponding names (indexes). If a value is undefined,
; the first entry in the index-list is used.
;
set RecBufCountIndex = *($(RecBufCountList), ~($(RecBufCountValues),$(RecBufCountValue)))
ifstr(i) $(RecBufCountIndex) == ""
set RecBufCountIndex = *($(RecBufCountList), RecBufCountDefault)
endif
set ExtPCIIndex = *($(ExtPCIList), ~($(ExtPCIValues),$(ExtPCIValue)))
ifstr(i) $(ExtPCIIndex) == ""
set ExtPCIIndex = *($(ExtPCIList), ExtPCIDefault)
endif
set ConnTypeIndex = *($(ConnTypeList), ~($(ConnTypeValues),$(ConnTypeValue)))
ifstr(i) $(ConnTypeIndex) == ""
set ConnTypeIndex = *($(ConnTypeList), ConnTypeDefault)
endif
set BusNoIndex = *($(BusNoList), ~($(BusNoValues),$(BusNoValue)))
ifstr(i) $(BusNoIndex) == ""
set BusNoIndex = *($(BusNoList), BusIndexDefault)
endif
;
adapteroptions = +
set from = adapteroptions
ifstr(i) $(!NTN_InstallMode) == "install"
;
; User will NOT be asked to change/verify configuration during
; normal or unattended installation, unless we are installing on
; NT v3.50.
;
ifint $(PCIDetectSupported) == $(TRUE)
; We will not ask user for configuration during installation
; if PCI detection is supported
goto unattended
endif
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
; Default parameters for unattended installation
goto unattended
endif
endif
set OldNetAddress = $(NetworkAddress)
;
; Load DLL containing dialogs and verification routines
;
LoadLibrary "Olicom Ethernet Driver Disk" $(DialogDllName) DialogHandle
;
; Read main dialog setup and show dialog
;
ifint $(PCIDetectSupported) == $(FALSE)
read-syms AdapterParameterDlg2$(!STF_LANGUAGE)
else
read-syms AdapterParameterDlg1$(!STF_LANGUAGE)
endif
ui start "InputDlg" $(DialogHandle)
ifstr(i) $(DLGEVENT) == "CONTINUE"
;
; parameters have already been stored at this stage
;
;
; Save new settings because this dialog might be called again.
; If CANCEL was pressed these values will not be used
;
set ConnTypeIndex = $(Combo1Out)
set RecBufCountIndex = $(Combo2Out)
set ExtPCIIndex = $(Combo3Out)
ifint $(PCIDetectSupported) == $(FALSE)
set BusNoIndex = $(Combo5Out)
endif
set NetworkAddress = *($(EditTextOut),1)
ui pop 1
goto nextstep
else-ifstr(i) $(DLGEVENT) == "EXIT"
set CommonStatus = STATUS_USERCANCEL
Debug-Output "Action: exit. Bye."
ui pop 1
FreeLibrary $(DialogHandle)
goto end
else
ui pop 1
Debug-Output "Action: unknown: "$(DLGEVENT)
FreeLibrary $(DialogHandle)
goto end
endif
nextstep =+
ifstr $(NetworkAddress) != ""
;
; If network address has been entered then verify that it is a
; valid address (not a multicast or broadcast address)
;
set FLibraryErrCtl = 1
LibraryProcedure DlgResult $(DialogHandle) VerifyEthAddress $(NetworkAddress)
set FLibraryErrCtl = 0
ifstr $(DlgResult) != "STATUS_SUCCESS"
FreeLibrary $(DialogHandle)
set Error = $(DlgResult)
goto nonfatal
endif
endif
FreeLibrary $(DialogHandle)
unattended =+
ifint $(OldVersionExisted) == $(TRUE)
ifstr(i) $(!NTN_InstallMode) == configure
goto writeparameters
endif
endif
StartWait
Ifint $(OldVersionExisted) != $(FALSE)
Goto installhardware
Endif
ifstr(i) $(!NTN_InstallMode) == "install"
Ifstr(i) $(DoCopy) == "YES"
Ifstr(i) $(SrcDir) == ""
read-syms AskSourceDlgText
Shell $(subroutineinf) DoAskSourceEx $(SrcDir) $(DlgText)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
Endif
Endif
install "Install-Option"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
endif
endif
;
; Insert hardware component in registry
;
installhardware =+
ifint $(PCIDetectSupported) == $(FALSE)
ifstr(i) $(!AutoNetInterfaceType) != ""
set BusTypeNum = $(!AutoNetInterfaceType)
else
set BusTypeNum = 5
endif
ifstr(i) $(!AutoNetBusNumber) != ""
set BusNumber = $(!AutoNetBusNumber)
else
set BusNumber = $(BusNoDefault)
endif
Set InstalledAdapter = "NO"
else
;
; If We are installing a PCI adapter so go search PCI bus
; for our adapter
;
set BusTypeNum = 5
set VendorID = 4113 ; Vendor ID: 1011h
set DeviceID = 25 ; Device ID: 19h
; Flag adapter already installed
Set InstalledAdapter = "YES"
; Get PCI information
Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(DeviceID)
set AdapterList = $($R0)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R0) == {}
;
; Adapter list is empty. No adapter of this type was found
;
else
;
; Adapter(s) has been found. We will try to find out if the (or
; these) adapter hasn't been installed already.
;
ForListDo $(AdapterList)
; Run through the Adapter list
; Get Bus number from list:
set TestBusNumber = *($($),1)
; Get SLot Number from list:
set TestSlotNumber = *($($),2)
; Check registry
Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(TestBusNumber), +
$(TestSlotNumber), $(ProductHardware$(Option)Description), +
$(ProductHardwareName), "NO"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr $($R0) != "NO_ERROR"
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) == "NO"
; This adapter in the AdapterList has not been install yet
ifstr(i) $(InstalledAdapter) == "YES"
; We have found an Adapter for which our driver
; has not been installed. Check if other drivers has
; been installed for this Adapter.
; Check registry
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
; We will do no further check in unattended install
Set InstalledAdapter = "NO"
set DetectedBusNumber = $(TestBusNumber)
set DetectedSlotNumber = $(TestSlotNumber)
Debug-Output "$(InfFile) $(Option): Installing Card at $(DetectedBusNumber):$(DetectedSlotNumber)!"
else
Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(TestBusNumber), +
$(TestSlotNumber), $(ProductHardware$(Option)Description), +
$(ProductHardwareName), "YES"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr $($R0) != "NO_ERROR"
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) == "NO"
; We have found an Adapter with no other installed
; drivers. Lets install.
; We can not Break from ForListDo, so we will
; just flag that we have found an adapter to install
Set InstalledAdapter = "NO"
set DetectedBusNumber = $(TestBusNumber)
set DetectedSlotNumber = $(TestSlotNumber)
else
Debug-Output "$(InfFile) $(Option): Card Already at $(TestBusNumber):$(TestSlotNumber) already installed!"
set Error = "An adapter at "$(TestBusNumber)":"$(TestSlotNumber)" (Bus : Slot) is already "+
"installed with a non Olicom RapidFire Ethernet 10/100 driver. Install anyway?"
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), WARNING, $(Error)
ifstr(i) $($R0) != STATUS_SUCCESSFUL
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) == "OK"
Set InstalledAdapter = "NO"
set DetectedBusNumber = $(TestBusNumber)
set DetectedSlotNumber = $(TestSlotNumber)
endif
endif
endif
endif
endif
EndForListDo
endif
Set BusNumber = $(DetectedBusNumber)
Set SlotNumber = $(DetectedSlotNumber)
endif
ifstr(i) $(InstalledAdapter) == "YES"
; We had no adapter to install. Exit
set Error = "Network card is not present in the system "+
"or network card already installed"
set CommonStatus = USER_CANCEL
set from = end
goto nonfatal
endif
;
; Install this adapter
;
Debug-Output "$(InfFile) $(Option): Installing Card at $(BusNumber):$(SlotNumber)!"
set ReturnTo = ComponentsHasBeenAdded
goto AddAdapterComponents
ComponentsHasBeenAdded =+
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "Cannot add hardware component"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add hardware component"
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
set KeyProduct = $($R1)
set KeyAdapterRules = $($R2)
set KeyParameters = $($R3)
set AdapterNumber = $($R4)
; ifint $(PCIDetectSupported) == $(FALSE)
set ThisProductTitle = "["$($R4)"] "$(ProductHardware$(Option)Title)
; else
; set ThisProductTitle = "["$($R4)"] "$(ProductHardware$(Option)Title)" ("$(BusNumber)":"$(SlotNumber)")"
; endif
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),$(ThisProductTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
CloseRegKey $(KeyProduct)
Set KeyProduct = ""
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
CloseRegKey $(KeyAdapterRules)
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add value list."
CloseRegKey $(KeyParameters)
goto fatalregistry
endif
;
; Write Adapter Parameters to registry
;
writeparameters = +
Ifstr(i) $(KeyParameters) == $(KeyNull)
Debug-Output "*** KeyParameters is NULL at writeparameters"
Endif
;
; Convert selections from combo-lists and radio-buttons into actual
; parameter values
;
set RecBufCountValue = *($(RecBufCountValues), ~($(RecBufCountList),$(RecBufCountIndex)))
set ExtPCIValue = *($(ExtPCIValues), ~($(ExtPCIList),$(ExtPCIIndex)))
set ConnTypeValue = *($(ConnTypeValues), ~($(ConnTypeList),$(ConnTypeIndex)))
ifstr(i) $(!NTN_InstallMode) != "install"
set BusNumber = *($(BusNoValues), ~($(BusNoList),$(BusNoIndex)))
endif
;
; Set up parameter list for AddValueList routine
;
set NewValueList = {{AdapterCFID,$(NoTitle),$(!REG_VT_DWORD),$(CFID_$(Option))},+
{AdapterType,$(NoTitle),$(!REG_VT_DWORD),$(AdapterType_$(Option))},+
{OSType,$(NoTitle),$(!REG_VT_DWORD),$(OSTypeValue)},+
{MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+
{ReceiveBuffers,$(NoTitle),$(!REG_VT_DWORD),$(RecBufCountValue)},+
{ExtendedPCI,$(NoTitle),$(!REG_VT_DWORD),$(ExtPCIValue)},+
{ConnectionType,$(NoTitle),$(!REG_VT_DWORD),$(ConnTypeValue)}}
ifstr $(NetworkAddress) != ""
set NewValueList = >($(NewValueList),{NetworkAddress,$(NoTitle),$(!REG_VT_SZ),$(NetworkAddress)})
endif
ifint $(PCIDetectSupported) == $(TRUE)
set NewValueList = >($(NewValueList),{SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(SlotNumber)})
endif
;---------------------------------------
; Add keyword to prevent driver from
; entering promiscuous mode
;
;set NewValueList = >($(NewValueList),{AllowTrace,$(NoTitle),$(!REG_VT_DWORD),0})
;
; Now update registry
;
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
Shell $(UtilityInf),AddDefaultNetCardParameters,$(KeyParameters)
endif
;
; If the network address has been deleted then also delete it from
; the registry.
;
ifstr $(OldNetAddress) != ""
ifstr $(NetworkAddress) == ""
DeleteRegValue $(KeyParameters) NetworkAddress
endif
endif
CloseRegKey $(KeyParameters)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
Debug-Output "Registry error: Add value list"
goto fatalregistry
endif
EndWait
goto successful
bindingadapter =+
set Error = "Binding: Sorry, not yet implemented."
goto fatal
;-----------------------------------------------
; Add Software component to registry
;-----------------------------------------------
;
;
AddAdapterComponents =+
ifint $(OldVersionExisted) == $(TRUE)
goto $(ReturnTo)
endif
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
$(NetEventDLL), ""
Set OEM_ABANDON_SOFTWARE = TRUE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "OEMNADUB.INF: Registry error: add software components"
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
CloseRegKey $($R4)
CloseRegKey $($R5)
goto fatalregistry
endif
set SoftProductKey = $($R1)
Set SoftNetRuleKey = $($R2)
Set SoftServiceKey = $($R3)
Set SoftParameterKey = $($R4)
Set SoftLinkageKey = $($R5)
set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
{MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
{MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
{Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add value list."
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
goto fatalregistry
endif
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
{use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
{bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
{bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add value list."
goto fatalregistry
endif
set OldVersionExisted = $(TRUE)
goto $(ReturnTo)
;-----------------------------------------------
; Remove Adapter Section
;-----------------------------------------------
;
; Remove all adapter information from the registry
;
removeadapter = +
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
else
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $(!NTN_RegBase)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
UpgradeSoftware = +
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set !UG_Filename = $($R0)
install "Install-Update"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
goto fatal
endif
SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
CloseRegKey $(KeyProduct)
else
goto fatalregistry
endif
goto end
successful = +
goto end
abandon = +
ForListDo $(OEM_ABANDON_OPTIONS)
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $($)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
EndForListDo
Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), FALSE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
warning = +
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(to)
else-ifstr(i) $($R1) == "CANCEL"
goto $(from)
else
goto "end"
endif
nonfatalinfo = +
Set Severity = STATUS
Set CommonStatus = STATUS_USERCANCEL
goto nonfatalmsg
nonfatal = +
Set Severity = NONFATAL
goto nonfatalmsg
nonfatalmsg = +
ifstr(i) $(Error) == ""
Set Severity = NONFATAL
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(from)
else
goto "end"
endif
fatalregistry = +
Shell "subroutn.inf" SetupMessage $(!STF_LANGUAGE) WARNING "Fatal Error"
Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
fatal = +
ifstr(i) $(Error) == ""
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto setfailed
ShellCodeError = +
set DlgType = "MessageBox"
set STF_MB_TITLE = "Error: "$(FunctionTitle)
set STF_MB_TEXT = "Shell Code Error"
set STF_MB_TYPE = 1
set STF_MB_ICON = 3
set STF_MB_DEF = 1
ui start "Error Message"
goto setfailed
setfailed = +
set CommonStatus = STATUS_FAILED
ifstr(i) $(OEM_ABANDON_ON) == TRUE
set OEM_ABANDON_ON = FALSE
goto abandon
endif
goto end
end = +
goto term
term = +
Return $(CommonStatus)
[Install-Option]
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
endif
Debug-Output "OEMSETUP.INF: [Install-Option] DoCopy = "$(DoCopy)
ifstr(i) $(DoCopy) == "YES"
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
endif
Exit
[Install-Update]
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Install-Dll]
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH)
endif
ifstr(i) $(DoCopy) == "YES"
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
else
; get minimum needed files for configuration
LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\OCE5XND3.DLL $(!STF_WINDOWSSYSPATH)\OCE5XND3.DLL
LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\OCE5XND3.HLP $(!STF_WINDOWSSYSPATH)\OCE5XND3.HLP
endif
exit
[Source Media Descriptions]
1 = "RapidFire 2327 Ethernet 10/100 PCI Adapter Driver Disk"
[ProductType]
STF_PRODUCT = Winnt
STF_PLATFORM = I386
[Files-Inf]
1, oemsetup.inf, SIZE=999, RENAME=$(!UG_Filename)
[Files-OCE5X_2327]
1, OCE5XND3.SYS, SIZE=999
[Files-Dll]
1, oce5xnd3.dll, SIZE=999
1, oce5xnd3.hlp, SIZE=999
[Files-dummy]
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.