MonitorMouse(TM) for Windows XP
Release 3.3
October 15, 2002
Elo TouchSystems, Inc.
MonitorMouse for Windows XP contains a native, 32-bit driver
designed for Windows XP, setup program, video alignment
program, 32-bit control panel program, and diagnostic
applications for Elo TouchSystems' touchmonitors.
=======================================================
Supported Touchmonitors and Elo Touchscreen Controllers
=======================================================
- All Elo Entuitive brand touchmonitors with an internal
serial controller
- Elo Serial Controllers (IntelliTouch(R) 2500S, 2310B,
2310, 2300, AccuTouch(R) 2210)
-------------------------------------------------------
| |
| This driver does not support Elo USB Touchmonitors, |
| Elo USB controllers or Elo PC-Bus controllers. |
| |
| Refer to www.elotouch.com for availability of Windows |
| XP drivers for these products. |
| |
-------------------------------------------------------
========================================
Installing MonitorMouse for Windows XP
========================================
Note: you must have administrator access rights on your
Windows XP system to install MonitorMouse for Windows
XP. You must also have administrator access rights to run
the touchscreen control panel and video alignment
applications.
1. Shutdown Windows and turn off your computer.
2. Install your touchmonitor hardware as described in the
IntelliTouch or AccuTouch Product Manual, Touchmonitor
Users Guide, or the Quick Start guide.
3. Start your computer.
4. After Windows loads, click the Start button, and then click
Run.
5. Click the Browse button to locate the SetupElo.exe program in
the directory containing the driver install files. Highlight
SetupElo.exe and click Open, then OK to run SetupElo.exe.
6. Follow the directions on the screen.
7. Choose the COM port to use with your touchmonitor.
Select the COM port you connected the touchscreen cable to
in step 2 above. All serial ports reported by Windows are
displayed.
8. Click Next.
9. Restart Windows when prompted. Make sure you remove any
floppy disks before restarting.
You must run the touchscreen video alignment program after
Windows starts up.
===============================================
Running the Touchscreen Video Alignment Program
===============================================
Use the following procedure to align your touchmonitor after
installation.
1. Choose Start/Settings/Control Panel and double-click
the Elo Touchscreen object.
2. Press the align button.
3. Touch each of the three targets as they appear on the
screen. Click Yes when the cursor lines up correctly
with your finger.
4. Click OK to close the touchscreen control panel.
==================================
Changing the Touchmonitor COM Port
==================================
Use the following procedure if you selected the wrong COM port
for your touchmonitor during installation or want to change the
COM port to use with your touchmonitor. You may have restart
Windows before the new setting will take effect.
1. Re-install the serial driver.
2. Or plug the touchscreen cable into the COM port that you have
selected during installation.
==========================================
Uninstalling MonitorMouse for Windows XP
==========================================
1. Click the Start button, point to Settings, and then click
Control Panel.
2. Double-click the Add/Remove Programs icon.
3. Select MonitorMouse for Windows XP from the list of
currently installed programs.
4. Click the Change/Remove button then follow the directions
on your screen.
5. Restart Windows to complete the uninstall process.
=============
Release Notes
=============
- You must have administrator access rights to run the Elo
Touchscreen control panel and video alignment applications.
- Because serial communications services are not available
until late in the Windows XP startup process, the
touchscreen may not begin to function until several seconds
after the Windows desktop is displayed.
- To enable the "2-wire", no-handshaking mode, set the
following DWORD registry key to 0 using regedit.exe:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services
\EloTouchscreen\NTSerial0\HardwareHandShaking
==========
Known Bugs
==========
- The touchscreen will not work properly when the mouse is
set for left-handed button configuration in the Mouse
Properties control panel. Touch will always perform a right
mouse function when the mouse is set for a left-handed
user.
- If you press the Cancel button on the Elo Touchscreen
control panel after using the Apply button, some of the
applied settings will become un-applied.
- Uninstalling the driver will leave the following empty
folder on your hard drive:
C:\Program Files\Elo TouchSystems
==============
Contacting Elo
==============
www.elotouch.com
e-mail: eloinfo@elotouch.com
Elo TouchSystems, Inc.
6500 Kaiser Drive
Fremont, CA 94555
USA
Phone: (800) 557-1458
(510) 739-4999
Fax: (510) 739-5353
Elo TouchSystems GmbH & Co. KG
Haidgraben 6
D-85521 Ottobrunn
Germany
Phone: +49 (0) 89/60822-0
Fax: +49 (0) 89/60822-150
Elo TouchSystems, NV
Diestsesteenweg 692
B-3010 Kessel-Lo
Belgium
Phone: +32 (16) 35-2100
Fax: +32 (16) 35-2101
Copyright (c) 2002 Elo TouchSystems, Inc.
All rights reserved.
MonitorMouse is a trademark of Elo TouchSystems, Inc.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.