1. cdsetup.zip Driver
2. README.TXT File Contents

README.TXT Driver File Contents (cdsetup.zip)

******************************************************************************
                 EPO CD-ROM 40X CR-840S - 36X CR-836S Device Driver V1.02
******************************************************************************


SYNTAX
======
                DEVICE = EPOCDROM.SYS /D:device_name [/options]


OPTIONS
=======

 /PIO[0~4]      Select PIO Mode 0~4 (Auto Mode if number is omitted)

 /DMA[0~2] or   Select Bus Master DMA Mode 0~2
 /BM[0~2]       (Auto Mode if number is omitted)
                If the motherboard does not support Bus Master DMA,
                The driver will automatic switch to PIO mode.

 /UDMA[0~2]     Select Ultra DMA Mode 0~2
                (Auto Mode if number is omitted)
                If the motherboard does not support Ultra DMA,
                The driver will automatic switch to DMA mode.

 /P:xxx,yy      Select Port Address and IRQ route; xxx = Port, yy = IRQ
                Example         Port    IRQ
                -----------------------------
                Primary         1F0     14
                Secondary       170     15
                Tertiary        1E8     11/12
                Quaternary      168     10/11

 /Q             Enable Quick Initialization


EXAMPLE
=======
                DEVICE = EPOCDROM.SYS /D:EPOCD001 /UDMA /Q
                DEVICE = EPOCDROM.SYS /D:MSCD001 /PIO4


MOTHERBOARDS AND CHIPSETS SUPPORTED
===================================

                        IDE         Vendor  Device  Rev.  PIO   DMA   UDMA
Vendor  Chipset         Controller  ID      ID      ID    Mode  Mode  Mode
----------------------------------------------------------------------------
Intel   430TX            PIIX4       8086h   7111h         0~4   0~2   0~2
        430HX,430VX      PIIX3       8086h   7010h         0~4   0~2
        430FX            PIIX        8086h   1230h         0~4   0~2
SiS     5597,5598        5597/5598   1039h   5513h   D0h   0~4   0~2   0~2
        5581,5582        5581/5582   1039h   5513h   D0h   0~4   0~2   0~2
        5571             5571        1039h   5513h   C0h   0~4   0~2
        5596/5513        5513        1039h   0597h   B0h   0~4   0~2
        551X             5513        1039h   5513h   00h   0~4   0~2
VIA     VP3              VT82C586B   1106h   0571h         0~4   0~2   0~2
        VP2/97           VT82C586B   1106h   0571h         0~4   0~2   0~2
        VP2              VT82C586A   1106h   0571h         0~4   0~2   0~2
        VPX/97           VT82C586B   1106h   0571h         0~4   0~2   0~2
        VPX              VT82C586A   1106h   0571h         0~4   0~2   0~2
        VP-1             VT82C586    1106h   1571h         0~4   0~2
        Apollo Master    VT82C576M   1106h   1571h         0~4   0~2
ALi     Aladdin V+       M1543       10B9h   5229h         0~4   0~2   0~2

  %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
     %							 %
     %	      Readme file for CD-ROM  ARTEC ACD365/ACD360	 %
     %							 %
     %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

     =================
     II.  REQUIREMENTS
     =================

     A. Hardware Requirements
	1. IBM PC/AT or compatible (80386-base system
	   recommended)
	2. Minimum EGA graphic display (VGA recommended)
	3. Minimum 2MB DRAM recommended
	4. One free IDE port
	5. One CD-ROM drive

     B. Software Requirement
	1. Microsoft Windows 3.1 or later
	2. MS-DOS version 5.0 or later
	3. MS-DOS CD-Extension (MSCDEX 2.21) or later



     ============================
     III. INSTALLATION PROCEDURES
     ============================

     Please observe the following steps to install the CD-ROM
     driver:

     1. Insert the installation diskette into a floppy disk
	drive of your computer.
     2. Change the directory to that of your floppy disk drive,
	then type "INSTALL [ENTER]" at the DOS prompt.
     3. Follow the on-screen instructions to complete the
	installation.
     4. Reboot your system to activate the driver.

     In general, you can just continually press the ENTER key to
     install the default settings. A directory (default C:\ACDROM)
     containing the CD-ROM drivers is created during installation.
     Your AUTOEXEC.BAT and CONFIG.SYS files are also modified to
     include the following lines:

     for CONFIG.SYS:
           DEVICE=C:\ACDROM\ACDRV.SYS /D:ARTCD001 /UDMA

     for AUTOEXEC.BAT:
	   <MSCDEX_DIR>\MSCDEX.EXE /D:ARTCD001



     ===============================
     IV. CHANGING THE CONFIGURATIONS
     ===============================

     To change the settings of the CD-ROM drive, use a text
     editor, such as EDIT.COM, to modify the command lines in
     , CONFIG.SYS and AUTOEXEC.BAT. Then restart your computer
     to activate it.

     A. Changing the CONFIG.SYS file

	DEVICE=<path>\ACDRV.SYS /D:<device_name>

	The <device_name> is the name MSCDEX uses to find the
	device driver. The maximum length of <device_name>
	string is 8 characters.

	Example:
	     DEVICE=C:\ACDROM\ACDRV.SYS /D:ARTCD001

	[Note] : If you use the TRIN4X.DSK in Novell system,
		 you must use the following configuration

	     DEVICE=C:\ACDROM\ACDRV.SYS /D:ARTCD001 /UDMA

     B. Changing the AUTOEXEC.BAT file

	MSCDEX [/E/K/S/V] [/D:<driver>...]
	       [/L:<letter>] [/M:<buffer>]

	Example:
	     C:\DOS\MSCDEX /D:ARTCD001

	For more information, please consult the MS-DOS
	online help for MSCDEX by typing HELP MSCDEX.