Copyright
Copyright (C) 1998 by this company. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of this
company.
Disclaimer
This company makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties, merchantability or fitness for any particular purpose. Any
software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not this
company, its distributor, or its dealer) assumes the entire cost of all
necessary servicing, repair, and any incidental or consequential damages ges
resulting from any defect in the software. Further, this company reserves
the right to revise this publication and to make changes from time to time in
the contents hereof without obligation to notify any person of such revision
or changes.
Other brand and product names are trademarks and/or registered trademarks of
their respective holders.
Federal Communications Commission
Radio Frequency Interference Statement
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and
if not installed and used in accordance with the instruction manual may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
* Consult the dealer or an experienced radio TV technician for help.
Notice:
The changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Specifications
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ DRIVE PERFORMANCE ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Disc Data Capacity: Mode 1 656 MB, Mode 2 748 MB ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Maximum Playing Time: 74 minutes and 42 seconds ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Data Transfer Rate (KB/s) ³ Mode 1 ³ Mode 2 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Normal speed ³ 150 ³ 171 ³
³ 36X CD-ROM ³ 150 * X ³ 171 * X ³
³ 40X CD-ROM ³ ³ ³
³ ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Data Buffer Size: 128 KB ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Drive Reliability (MTBF): 25,000 POH (25% duty cycle at room ³
³ temperature) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ COMPACT DISC ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Disc Type (data format): CD-Audio, CD-ROM (mode 1 and 2 ) ³
³ CD-ROM/XA (mode 2, form 1 and form 2) ³
³ CD-EXTRA, CD-I, Photo-CD (single and ³
³ multiple sessions), CD-WO, I-Trax CD, CD-RW³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Disc Size: 80-mm and 120-mm discs ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ INTERFACE ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Drive Interface Type: E-IDE (conforms to SFF8020 v1.2) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ AUDIO ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Analog Audio Output Ports: Headphone jack on front panel ³
³ Line-out connector on the rear end of the ³
³ drive (two stereo channels for each output ³
³ port) ³
³ Digital Audio Output Port: Two-pin line out connector on the rear ³
³ end of the drive ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Audio Sampling Frequency: 44.1 KHz ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Audio Quantization: 16 bits ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ POWER REQUIREMENTS ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Voltage: +5V, +12V ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ PHYSICAL CHARACTERISTICS ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Front Panel: Load/Eject button, Play/Skip button, ³
³ Power-on/Busy LED indicator, 3.5-mm stereo ³
³ headphone jack, rotary volume control knob ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Rear Panel: Power-supply connector, IDE interface ³
³ connector, master/slave jumper, ³
³ analog audio output connector, ³
³ digital audio output connector, ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Example: 40X CD-ROM = 150* 40 = 6000KB/sec.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ PHYSICAL CHARACTERISTIC ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Mount: Horizontal ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Dimensions: 148mm x 42mm x 210mm (5.9" x 1.7" x 8.3") ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Weight: Less than 1.1kg (2.4 lbs) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ENVIRONMENT REQUIREMENT ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Temperature: Operating +5 degree ~ +45 degree ³
³ Non-operating -20 degree ~ +55 degree ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Humidity: Operating 20% ~ 80% RH ³
³ Non-operating 20% ~ 80% RH ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ LASER COMPONENT RADIATION DATA ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Wavelength: 785 +- 25nm ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Emission light output power: Less than 0.3 mWPmax ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
I Installing the CD-ROM Drive
Before you begin, turn off the system power. Follow the steps below to
install the CD-ROM drive:
1. Remove the cover from your system. Refer to your system user's manual.
2. Adjust the Master/Slave jumpers on the back of the CD-ROM drive as
necessary. (The factory default of the slave mode normally should not
be changed. Please refer to Section 4 for more information)
3. Insert the CD-ROM drive unit into a free 5.25-inch drive bay. Secure
the CD-ROM drive to the drive bay rails with the mounting screws
(included in the CD-ROM package). Refer to your system manual for
instructions on how to install a drive.
4. Plug a free power connector inside your PC into the Power socket on the
back of the CD-ROM drive.
5. Plug a free IDE connector inside your PC into the drive's IDE interface
socket.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ AUDIO HOST INTERFACE POWER ³
³ ÚÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³
³ ³ R G G L ³ ³ C S M ³ ³ 39 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 1 ³ ³ 5V G G 12V ³ ³
³ ³ ³ ³ S L A ³ ³ 40 ÄÄÄÄÄÄÄ ÄÄÄÄÄÄÄ 2 ³ ³ ³ ³
³ ÀÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÙ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ÚÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³
³ ³ ³ ³ o o o ³ oooooooooooooooooooo ³ o o o o ³ ³
³ ³o o ³ o o o o ³ o o o ³ oooooooooo ooooooooo ³ ³ ³
³ ÀÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
ÚÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄ¿
³ ³ ³ ³ ³ ³
³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³ ³
ÚÁÄÄÄÄÄÄÄÁ¿ ³³³³³³³³³³³³³³³³³³³³ ÀÄÄÄÄÄÄÄÄÄÙ
³ ³ ³³³³³³³³³³³³³³³³³³³³ ³ ³ ³ ³
ÀÄÄÄÄÄÄÄÄÄÙ ³³³³³³³³³³³³³³³³³³³³ ³ ³ ³ ³
³ ³ ³ ³ ³³³³³³³³³³³³³³³³³³³³ Red ³ ³ ³ ³
³ ³ ³ ³ Red Strip ³³³³³³³³³³³³³³³³³³³³ Strip ³ ³ ³ ³
³ ³ ³ ³<-------- ³³³³³³³³³³³³³³³³³³³³<---- ³ ³ ³ ³
³ ³ ³ ³ ³³³³³³³³³³³³³³³³³³³³ ³ ³ ³ ³
Audio Cable IDE Cable Power Cable
NOTE: The red edge of the IDE cable corresponds to pin 1 of the IDE
interface on the CD-ROM drive.
If you have a sound card, you can also connect a 4-pin analog audio
cable to the analog audio-out connector of your CD-ROM drive and the
audio-in connector of the sound card.
If you have a digital audio device, you can also connect a 2-pin digital
audio cable to the digital audio-out connector of your CD-ROM drive and
the audio-in connector of your digital audio device.
6. Replace the cover and turn on the power.
II Installing the CD-ROM Drivers
The CD-ROM package comes with an installation utility. This utility
installs the CD-ROM drivers needed by your CD-ROM drive to interact with your PC. The driver installation diskette includes the following files:
* INSTALL.EXE
* README.EXE
* README.TXT
* CDTECH.SYS
* UDMA.TXT
* CMNAE2.TXT
* CMNAF2.TXT
* CMNAG2.TXT
* CMNAS2.TXT
For DOS and Windows 3.1
To install the driver in DOS or Windows 3.1:
1. Insert the installation diskette in your 3.5-inch diskette drive and
make it the active drive.
2. At the DOS prompt, type:
INSTALL ENTER
3. Follow the screen instructions to complete the installation.
The installation program creates a directory (C:\CDROM) containing the
CD-ROM drivers. It also updates your AUTOEXEC.BAT and CONFIG.SYS files
as follows:
CONFIG.SYS
DEVICE=C:\CDROM\CDTECH.SYS /D:MSCD001 /UDMA2 /V
AUTOEXEC.BAT
C:\DOS\MSCDEX.EXE /D:MSCD001 /M:10
Changing the Settings After Installation
To reconfigure the settings of the CD-ROM driver, use a text editor (such
as EDIT.COM) to modify the DEVICE= and LASTDRIVE= command lines in the
CONFIG.SYS and AUTOEXEC.BAT files. Then restart your computer.
Changing the CONFIG.SYS File
Add the following line to your CONFIG.SYS:
DEVICE = <PATH>\CDTECH.SYS /D:<DEVICE_NAME>
The <DEVICE_NAME> is the name of the MSCDEX file that will be used to find
the device driver. The maximum length of the <DEVICE_NAME> string is eight
characters.
For example:
DEVICE=C:\CDROM\CDTECH.SYS /D:MSCD001
For Ultra DMA Function, please refer to UDMA.TXT
For Windows 95 and Windows NT Environment
Windows 95 and Windows NT will automatically detect the new CD-ROM drive
and load the appropriate device driver. However, there are times when
Windows can not detect the CD-ROM drive. You will have to load the
drivers manually.
To install the drivers manually:
1. Click the Control Panel Icon in My Computer and then click Add New
Hardware. The Add New Hardware window appears.
2. The program will automatically search for your new CD-ROM Drive and
load the appropriate driver.
For OS/2 Warp
Under OS/2 Warp, select the non-listed CD-ROM option. This option
supports the standard ATAPI CD-ROM drives. After selecting this option,
OS/2 will auto-detect the CD-ROM drive.
III Using the CD-ROM Drive
In most cases, software applications that utilize CD-ROM drives control the
CD-ROM drive operations directly. However, you can control the drive
manually using the front-panel controls.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³
³ ³ ³ ³
³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³
³ o ³
³ ï () ÚÄÄÄÄÄÄ¿ o ³ ÚÄÄÄÄÄÄÂÄÄÄÄÄ¿ ³
³ ÀÄÄÄÄÄÄÙ ³ ³ >> ³ þ ³ ³
³ ³ ³ ³ ÀÄÄÄÄÄÄÁÄÄÄÄÄÙ ³
ÀÄÄÄÄijÄÄÄÄÄÄijÄÄÄÄÄijÄÄijÄÄÄÄÄÄÄÄÄÄÄÄijÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
³ ³ ³ ³ ³ ³ ³
³ ³ ³ ³ ³ ³ ³
³ ³ ³ ³ ³ ³ ³
1 2 6 3 7 4 5
1. Headphone Jack
The 3.5-mm stereo headphone jack allows you to listen to audio CDs via
stereo headphones.
2. Volume Control
The volume control is a rotary knob that allows you to control the sound
level from the headphone jack.
3. Power-on/Busy LED
The Power-on/Busy LED indicator lights up when the CD-ROM drive is being
accessed. The LED blinks during a seek operation.
4. Play/Skip Button
The Play/Skip button allows you to play and skip tracks on an audio CD.
5. Load/Eject Button
The Load/Eject button opens the motorized CD tray for loading and
removing CDs. When an audio CD is being played, pressing this button
stops the playing of the CD.
6. Emergency-eject Hole
The emergency-eject hole allows the user to open the CD tray when the
system has no power.
7. Disc Tray
The disc tray opens and closes for the loading and removal of CDs.
IV Emergency-eject Option
The Emergency-eject option allows the user to manually open the CD tray
during a power malfunction.
Follow these steps to manually open the disc tray:
1. Locate the tiny hole at the bottom of the disc tray. Gently poke the
hole with a sharp needle or a clip.
2. When the disc tray opens, pull out the tray and remove the disc from the
CD-ROM drive.
V Jumper Settings
This appendix explains the jumper settings on the drive and lists the pin
configurations of each connector on the rear panel.
The CD ROM drive comes with one jumper. This jumper determines how your
CD-ROM drive functions. The figure and table below show the four possible
jumper settings and their functions.
C S M C S M C S M C S M
Û o o o o Û o Û o o o o
Û o o o o Û o Û o o o o
Use CSEL Master Slave Slave
ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÑÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º Jumper Setting ³ Function º
ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍØÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º C ³ Use CSEL º
ÇÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĶ
º M ³ Master º
ÇÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĶ
º S ³ Slave º
ÇÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĶ
º None ³ Slave º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÏÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.