ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º README for º º º º UM8672 VL BUS IDE DEVICE DRIVERS º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ (1). UM8672 VL BUS IDE DEVICE DRIVERS are saved in this diskette. These drivers are not only designed for UM8672 to improve IDE I/O data transfer rate between IDE hard disk(s) and your system, but also support up to 4 hard drives. The following files are included : 1. README 2. INSTALL4.EXE ( V1.5, auto install utility ) 3. UM8672.SYS ( V1.5, DOS device driver ) 4. UM8672.386 ( V1.5, Windows device driver for V3.1x ) 5. INT13.386 ( V1.3, Windows device driver for V3.1x ) 6. UMC1S506.ADD ( V1.4, OS/2 device driver for V2.x ) 7. UMC310.DSK ( V1.3, NetWare device driver for V3.10 ) 8. UMC311.DSK ( V1.3, NetWare device driver for V3.11, 3.12 ) 9. UMC401.DSK ( V1.3, NetWare device driver for V4.0x ) 10. UNIX.UMC ( V1.4, SCO UNIX device drive for 3.2V4.1 ) 11. V1508672.PT4 ( Release Note for Diskette Version 1.5 ) (2). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install DOS Device Driver for UM8672 VL-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The INSTALL4.EXE utility can install DOS device driver automatically. If you want to install DOS device driver manually or change the drive speed, please follow the steps below. I. Copy the DOS\UM8672.SYS into the appropriate path. II. Add following statement to your CONFIG.SYS file to auto load the driver during bootup. device=[drive:][\path\]UM8672.SYS[/D<n:m>][/Cyl<n:m>][/Hd<n:m>][/Sec<n:m>] where D<n:m> Drive n speed m(0-11) ( 0 the lowest ) Cyl<n:m> Drive n(2-3) cylinder number m Hd<n:m> Drive n(2-3) head number m Sec<n:m> Drive n(2-3) sector number m For instance, the user wants to load UM8672.SYS with drive 0 speed = 6, and the DOS driver resides in the root directory of the drive C:. Add the following statement to your CONFIG.SYS file. DEVICE = C:\UM8672.SYS /D0:6 You don't need to specify drive speed parameters usually, because the device driver is reconfigured for the optimal speed setting. III. Reboot your system. IV. UM82C863, UM8663, UM8668 & UM8672 Software Switch Function En/Disable Hot-key (F10): You can press F10 to get such a picture (power on default): ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ 1. FDC En/Disable : Enable ³ ³ FDC Port Select : 3F1 => 3F7 ³ ³ 2. Primary Serial Port : Enable ³ ³ Primary Serial Port Select : COM1 (3F8) ³ ³ 3. Secondary Serial Port : Enable ³ ³ Secondary Serial Port Select : COM2 (2F8) ³ ³ 4. Parallel Port : Enable ³ ³ Parallel Port Select : 3F8 => 37F ³ ³ 5. Primary IDE En/Disable : Enable ³ ³ Secondary IDE En/Disable : Disable ³ ³ 6. Game Port En/Disable : Enable ³ ³ 7. Partition table write protected En/Disable : Disable ³ ³ ³ ³ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» ³ ³ ºPress <Escape> Key to Quit setup º ³ ³ º <Enter> Key to Set status & Quit º ³ ³ º <Arrow Up> Key to Select item up º ³ ³ º <Arrow Down> Key to Select item down º ³ ³ º <Space> Key to Toggle status º ³ ³ ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The user should consider the system environment to change the setup. (3). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install Windows Device Driver V3.x for VL-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ The INSTALL4.EXE utility can install Windows device driver automatically. If you want to install Windows device driver for your system manually or change the drive speed, please follow the steps below. I. Copy the Windows\UM8672.386 and Windows\INT13.386 into the appropriate path. II. Check if the following lines exist in the [386Enh] section of your SYSTEM.INI file. [386Enh] 32BitDiskAccess=ON device=*int13 device=*wdctrl If any statement does not exist, please add it to the [386Enh] section. Please add a preceding semi-colon in front of "device=*wdctrl" and "device=*int13" command lines. If "32BitDiskAccess" option is set to be "OFF", Please change it to be "ON". III. Add these following statements to the [386Enh] section in your \WINDOWS\SYSTEM.INI file. device = [drive:][\path\] UM8672.386 device = [drive:][\path\] INT13.386 DriveSpeed = [/D<n:m>] where D<n:m> Drive n speed m(0-11) ( 0 the lowest ) For instance, the user wants to load Windows drivers with drive 1 speed = 11, and the Windows drivers reside in the WINDOWS\ SYSTEM directory of the drive C:. Add the following statements to your SYSTEM.INI file. [386Enh] 32BitDiskAccess=ON ;device=*int13 ;device=*wdctrl DriveSpeed = /D1:11 device = c:\windows\system\UM8672.386 device = c:\windows\system\INT13.386 You don't need to specify drive speed parameters usually, because the device driver is reconfigured for the optimal speed setting. IV. Reenter your Windows. (4). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install OS/2 Device Driver V2.x for VL-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ If you want to install OS/2 device driver for your system, please follow the steps below. I. Copy the OS2\UMC1S506.ADD into the OS2 directory of your system. II. Check if the following line exists in the CONFIG.SYS file. BaseDev = IBM1S506.ADD If the statement exists, please delete it or add "REM" in front of it. III. Add this following statement to your CONFIG.SYS file. BaseDev = UMC1S506.ADD [/A:<0 or 1> /U:<0 or 1> /S:<speed>] where speed : drive speed setting from 0 to 11 ( 0 the lowest ) Note : The user MUST NOT specify either drive or path name. For instance, the user wants to load UMC1S506.ADD with drive (Unit) 0 speed 6 and drive (Unit) 1 speed 11 which are attached on Adapter 0. Add the following statement to your CONFIG.SYS file. BaseDev = UMC1S506.ADD /A:0 /U:0 /S:6 /U:1 /S:11 You don't need to specify drive speed parameters usually, because the device driver is reconfigured for the optimal speed setting. IV. Reboot your system. (5). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install NetWare Device Driver for VL-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ If you want to install NetWare device driver for your system, please follow the steps below. I. Copy the NetWare\UMCxxx.DSK into the appropriate path. II. Bring up the NetWare server of your system. III. Type the following statement after the ":" prompt :load UMCxxx PORT=<x> INT=<y> [/D<n:m>] where x 1F0 or 170 y E or F D<n:m> Drive n speed m(0-11) ( 0 the lowest ) Note : You MUST NOT load the ISADISK.DSK when you are installing UMCxxx.DSK Netware driver. For instance, the user wants to load UMC310.DSK with drive 0 speed 6 and drive 1 speed 11 which are attached on the controller. Add the following statement after the ":" prompt. :LOAD UMC310 /D0:6 /D1:11 PORT=1F0 INT=E You don't need to specify drive speed parameters usually, because the device driver is reconfigured for the optimal speed setting. (6). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Install SCO UNIX Device Driver for VL-Bus IDE Controller ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ If you want to install SCO UNIX device driver for your system, please follow the steps below. Type the following statements under UNIX system. I. mkdir /UM8672.bin II. cd /UM8672.bin III. doscp a:unix.umc . IV. tar xf - < unix.umc V. cd /UM8672.bin VI. ./istl.um8672 If you want to remove SCO UNIX device driver from your system, please follow the steps below. Type the following statements under UNIX system. I. cd /UM8672.bin II. ./rm.um8672 (7). ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³ Trademark Acknowledgments ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ VL-Bus is a trademark of the Video Electronics Standards Association. MS-DOS and Windows are registered trademarks of Microsoft Corporation. OS/2 is a registered trademark of IBM Corporation. NetWare is a registered trademark of Novell Corporation. Other brand names or trademarks are registered trade marks of their respective holders.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.