;*********************************************************************** ; Windows NT OEMSETUP.INF for ; ; Intel EtherExpress PRO/100+ PCI Adapter ; ; Copyright© 1994-1997 Intel Corporation. All rights reserved. ;*********************************************************************** ; ; ***************** Version 29 ***************** ; [Identification] OptionType = NetAdapter [PlatformsSupported] ISA EISA MCA PCI "Jazz-Internal Bus" [LanguagesSupported] ENG [Options] E100BEXP E100BPCI E10PPCI E100BRWA [OptionsTextENG] E100BEXP = "Intel EtherExpress PRO Adapter" [FileConstants] NDIS3Name = "E100B" NDIS4Name = "E100BNT" ExeName = "PROSET" Sp1Name = "EP100DG" Sp3Name = "SPDO3DG" KddName = "PROKDD" ProdHelp = "E100SET" GenHelp = "557SET" DllName = "EPRO100" AftName = "IAFT" Manufacturer = "Intel" ProductSoftwareName = "E100B" ProductSoftwareTitle = "Intel EtherExpress PRO Adapter" ProductSoftwareImagePathNDIS3 = "%SystemRoot%\System32\drivers\e100b.sys" ProductSoftwareImagePathNDIS4 = "%SystemRoot%\System32\drivers\e100bnt.sys" NetRuleSoftwareType = "E100BSys ndisDriver E100BDriver" NetRuleSoftwareBindForm = """E100BSys"" yes no container" NetRuleSoftwareClass = {"E100BDriver basic"} NetRuleSoftwareBindable = {"E100BDriver E100BAdapter non exclusive 100"} ImagePathNDIS3 = "\SystemRoot\System32\drivers\e100b.sys" ImagePathNDIS4 = "\SystemRoot\System32\drivers\e100bnt.sys" Configure = "EPRO100_Configure" Detect = "EPRO100_Detect" Diagnose = "EPRO100_Diagnose" DLL = "EPRO100.DLL" RegistryKey = "EPRO100_GetRegistryKey" Summary = "EPRO100_Resource_Summary" AdapterDescription = "EPRO100_GetAdapterDescription" InstallAnyway = "EPRO100_InstallAnyway" DeviceExist = "EPRO100_DeviceExist" GetExtendedFeatures = "EPRO100_GetExtendedFeatures" Adapter = "Intel EtherExpress PRO Adapter" Help = "E100SET.HLP" ExeKeyName = $(!NTN_ServiceBase)"\PROSet" ExeAdapterName = "EPRO100" ExeParameters = "Parameters" ProductHardwareName = "E100B" ProductHardwareTitle = "Intel EtherExpress PRO Adapter" ProductHardwareDescription = "Intel EtherExpress PRO Adapter" NetRuleHardwareType = "E100B E100BAdapter" NetRuleHardwareBindForm = " yes yes container" NetRuleHardwareClass = {"E100BAdapter basic"} ProductHardwareE100BEXPTitle = "Intel EtherExpress PRO Adapter" ProductHardwareE100BEXPDescription = "Intel EtherExpress PRO Adapter" FuncTitle = "Intel EtherExpress PRO Adapter Setup" ProdSoftwareDescription = "Intel EtherExpress PRO Adapter Driver" ProdHardwareDescription = $(ProductHardwareTitle) Disk1 = "Intel EtherExpress PRO Adapter Driver Disk" Path = "NT\" BusNumber = "0,7,BusNumber,0,2,0,0,16,1" BusType = "0,7,BusType,0,2,5,2,5,1" BusTypeLocal = "0,7,BusTypeLocal,0,2,5,2,5,1" Eid = "0,7,Eid,0,2,0,0,4294967295,1" Enhanced = "1,4,Enhanced Mode,0,1,On,Off,On" Fifo = "0,3,Fifo Depth,0,2,12,0,15,1" ForceDpx = "1,4,Duplex Mode,0,1,Auto,Auto,Half,Full" MediaType = "0,7,MediaType,0,2,1,1,1,1" MsPciScan = "0,4,MsPciScan,0,2,1,0,1,1" NumCoalesce = "1,7,Coalesce Buffers,0,2,8,1,32,1" NumRfd = "1,7,Receive Buffers,0,2,32,1,1024,1" NumTbd = "0,3,Transmit Buffer Descriptors,0,2,64,1,65535,1" NumTbdPerTcb = "0,4,Transmit Buffers per Frame,0,2,12,1,16,1" NumTcb = "1,7,Transmit Control Blocks,0,2,16,1,80,1" Off = "1,3,Off Timer,0,2,2,1,65535,1" On = "1,3,On Timer,0,2,32768,1,65535,1" RxDmaCount = "0,4,RxDmaCount,0,2,0,0,63,1" RxFifo = "0,4,Receive Fifo Depth,0,2,8,0,15,1" SlotNumber = "0,7,SlotNumber,0,2,0,0,16,1" Speed = "1,7,Network Speed,0,4,Auto,Auto,0,10Mbps,10,100Mbps,100" Threshold = "0,7,Transmit Threshold,0,2,16,0,200,1" TxDmaCount = "0,4,TxDmaCount,0,2,0,0,63,1" TxFifo = "0,4,Transmit Fifo Depth,0,2,8,0,15,1" UnderrunRetry = "0,4,UnderrunRetry,0,2,1,0,3,1" PerfOptims = "0,4,PerfOptims,0,2,0,0,65535,1" UcodeSW = "0,7,UcodeSW,0,2,1,0,1,1" Adaptive_IFS = "1,7,Adaptive Inter-Frame Spacing,0,2,1,0,255,1" Txmitwait = "0,7,Txmitwait,0,2,1,0,255,1" OLD_1BYTE = 139 OLD_2BYTE = 98 NETCARD_ID = 25227 ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion" ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters" UtilityInf = "UTILITY.INF" ParamInf = "NCPARAM.INF" subroutineinf = "SUBROUTN.INF" SoftwareType = "driver" Exit_Code = 0 NetRuleSoftwareUse = $(SoftwareType) NetEventDLL = "%SystemRoot%\System32\netevent.dll" IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll" ProductMajorVersion = "3" ProductMinorVersion = "0" ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion) ATeamSoftwareType = "driver" ProductATeamMajorVersion = "4" ProductATeamMinorVersion = "0" ProductATeamSoftwareTitle = "Intel Adapter Fault Tolerance NDIS Miniport Driver" ProductATeamSoftwareDescription = "Intel Adapter Fault Tolerance NDIS Miniport Driver Description" ProductATeamTransportTitle = "Intel Adapter Fault Tolerance Module" ProductATeamTransportDescription = "A software module that provides the Intel Adapter Fault Tolerance capability to your EtherExpress adapter." ProductATeamHardwareTitle = "Intel Adapter Fault Tolerance Team" ProductATeamHardwareDescription = "A team of Intel EtherExpress PRO/100+ Adapters working together to provide high availability, fail safe network operation." ProductATeamSoftwareImagePath = "\SystemRoot\System32\drivers\iaft.sys" NetRuleATeamSoftwareReview = 1 ProductATeamSoftwareName = "iAFT" NetRuleATeamSoftwareType = "iaftSys intermediateDriver" NetRuleATeamSoftwareUse = $(SoftwareType)" none none" NetRuleATeamSoftwareBindForm = """iaftSys"" yes no container" NetRuleATeamSoftwareClass = { + "intermediateDriver ndisDriver yes" + } NetRuleATeamSoftwareBindable = { + "intermediateDriver virtualAdapter non exclusive 100", + } ProductATeamTransportName = "iAFTProtocol" NetRuleATeamTransportType = "multispan intermediateTransport" NetRuleATeamTransportUse = "transport none none" NetRuleATeamTransportBindForm = "iAFTProtocol yes yes container" NetRuleATeamTransportClass = { + "intermediateTransport basic yes", + } NetRuleATeamTransportBindable = { + "intermediateTransport ndisDriver non non 100", + } ProductATeamHardwareName = "iAFT" NetRuleATeamHardwareType = "iAFT virtualAdapter" NetRuleATeamHardwareClass = {"virtualAdapter basic"} NetRuleATeamHardwareBindForm = " yes yes container" ATeamTransportKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductATeamTransportName)"\CurrentVersion" ATeamTransportParamKeyName = $(!NTN_ServiceBase)"\"$(ProductATeamTransportName)"\Parameters" ProductATeamKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductATeamSoftwareName)"\CurrentVersion" PROSetKeyName = $(!NTN_ServiceBase)"\PROSet" PROSetAdapterName = "EPRO100" PROSetParameters = "Parameters" EE16_1BYTE = 139 EE16_2BYTE = 98 NETCARD_ID = 25227 [Files-Inf] 1, oemsetup.inf, SIZE=50000, RENAME=$(!UG_Filename) [Files-N3NDIS3] 1, $(Path)$(NDIS3Name).SY_, SIZE=50000, RENAME=$(NDIS3Name).SYS [Files-N3NDIS4] 1, $(Path)$(NDIS4Name).SY_, SIZE=50000, RENAME=$(NDIS4Name).SYS 1, $(Path)$(AftName).SY_, SIZE=50000, RENAME=$(AftName).SYS [Files-Exe] 1, $(Path)$(ExeName).EX_, SIZE=50000, RENAME=$(ExeName).EXE 1, $(Path)$(ExeName).CP_, SIZE=50000, RENAME=$(ExeName).CPL 1, $(Path)$(Sp1Name).DL_, SIZE=50000, RENAME=$(Sp1Name).DLL 1, $(Path)$(ProdHelp).HL_, SIZE=50000, RENAME=$(ProdHelp).HLP 1, $(Path)$(GenHelp).HL_, SIZE=50000, RENAME=$(GenHelp).HLP 1, $(Path)$(DllName).DL_, SIZE=50000, RENAME=$(DllName).DLL [Files-Exe-Drivers] 1, $(Path)$(Sp3Name).SY_, SIZE=50000, RENAME=$(Sp3Name).SYS 1, $(Path)$(KddName).SY_, SIZE=50000, RENAME=$(KddName).SYS [ProductType] STF_PRODUCT = Winnt STF_PLATFORM = I386 [GeneralConstants] from = "" to = "" ExitCodeOk = 0 ExitCodeCancel = 1 ExitCodeFatal = 2 KeyNull = "" MAXIMUM_ALLOWED = 33554432 RegistryErrorIndex = NO_ERROR KeyProduct = "" KeyParameters = "" TRUE = 1 FALSE = 0 NoTitle = 0 ExitState = "Active" OldVersionExisted = $(FALSE) DriverPath = $(!STF_NTPATH)\drivers [FileConstantsENG] ProCaption = "Windows NT Setup" ProCancel = "Cancel" ProCancelMsg = "Windows NT Networking is not correctly installed. "+ "Are you sure you want to cancel copying files?" ProCancelCap = "Network Setup Message" ProText1 = "Copying:" ProText2 = "To:" FunctionTitle = $(FuncTitle) ProductSoftwareDescription = $(ProdSoftwareDescription) ProductHardwareDescription = $(ProdHardwareDescription) ConnectionList = {} ConnectionValues = {} [date] Now = {} ? $(!LIBHANDLE) GetSystemDate [Source Media Descriptions] 1 = $(Disk1) , TAGFILE = d100disk [Signature] FileType = MICROSOFT_DRVLIB_FILE [GetSignature] read-syms Signature return $(FileType) [Identify] read-syms Identification set Status = STATUS_SUCCESSFUL set Identifier = $(OptionType) set Media = #("Source Media Descriptions", 1, 1) Return $(Status) $(Identifier) $(Media) [ReturnOptions] set Status = STATUS_FAILED set OptionList = {} set OptionTextList = {} set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) in $(LanguageList) ifstr(i) $($1) == "" goto returnoptions endif set PlatformList = ^(PlatformsSupported, 1) Ifcontains(i) $($1) in $(PlatformList) goto returnoptions else set Status = STATUS_NOTSUPPORTED goto finish_ReturnOptions endif else set Status = STATUS_NOLANGUAGE goto finish_ReturnOptions endif returnoptions = + set OptionList = ^(Options, 1) set OptionTextList = ^(OptionsText$($0), 1) set Status = STATUS_SUCCESSFUL finish_ReturnOptions = + Return $(Status) $(OptionList) $(OptionTextList) [InstallOption] set Status = STATUS_FAILED set Option = $($1) set SrcDir = $($2) set AddCopy = $($3) set DoCopy = $($4) set DoConfig = $($5) set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) NOT-IN $(LanguageList) Return STATUS_NOLANGUAGE endif set-subst LF = "\n" read-syms GeneralConstants read-syms FileConstants ifstr(i) $(!NTN_Origination) == "NCPA" set Continue = "OK" endif read-syms FileConstants$(!STF_LANGUAGE) detect date set-title $(FunctionTitle) set CurrentVersionValue = "" OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(!REG_KEY_READ) KeyWinNT ifstr(i) $(KeyWinNT) != "" GetRegValue $(KeyWinNT) "CurrentVersion" CurrentVersionValue CloseRegKey $(KeyWinNT) endif set m_WinNTVersion = *($(CurrentVersionValue),4) set to = Begin set from = Begin ifcontains(i) $(m_WinNTVersion) in {"3.50", "3.51"} Shell $(UtilityInf), GetBusTypeNum ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif Set PlatformList = ^(PlatformsSupported, 1) Set MachineType = *($(PlatformList), $($R1)) else Set MachineType = $(!STF_BUSTYPE) endif set CommonStatus = STATUS_SUCCESSFUL EndWait Begin = + Set ActivateDetection = FALSE Ifstr(i) $(!NTN_InstallMode) == deinstall set StartLabel = removeadapter else-Ifstr(i) $(!NTN_InstallMode) == Update set StartLabel = UpgradeSoftware else-Ifstr(i) $(!NTN_InstallMode) == bind set StartLabel = bindingadapter else-Ifstr(i) $(!NTN_InstallMode) == configure set ActivateDetection = TRUE set StartLabel = configureadapter ifstr(i) $(MachineType) == "MCA" Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE else Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_HARDWARE endif set Error = $($R0) set from = end set to = end goto nonfatalinfo endif Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) set from = end set to = end goto nonfatalinfo endif else set ActivateDetection = TRUE set StartLabel = installadapter set OEM_ABANDON_OPTIONS = {} set OEM_ABANDON_SOFTWARE = FALSE set OEM_ABANDON_ON = TRUE endif Set DetectedCard = FALSE Ifstr(i) $(ActivateDetection) != TRUE Goto $(StartLabel) Endif ifstr(i) $(MachineType) == "MCA" goto CheckForMCA endif set IRQValue = *($(IRQList), 2) set IOAddrValue = *($(IOAddrList), 1) set IOReadyValue = *($(IOReadyList), 2) set TransceiverValue = *($(TransceiverList), 4) Ifstr(i) $(!STF_NCDETECT) == YES Ifstr(i) $(!STF_NCOPTION) == $(Option) Set DetectedCard = TRUE Endif Endif Shell "" DebugConfiguration "After parameter querying" Set from = $(fatal) Set to = $(fatal) Goto $(StartLabel) installadapter = + OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) CloseRegKey $(KeyProduct) ifstr(i) !(NTN_RegBase) == $(ProductKeyName) Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+ $(ProductVersion) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto end else Shell $(UtilityInf), CardExistedDlg ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) != "OK" goto end endif set OldVersionExisted = $(TRUE) endif endif ifcontains(i) $(m_WinNTVersion) in {"3.50", "3.51"} Ifstr(i) $(DetectedCard) != TRUE Goto adaptersetup Endif else Goto adaptersetup end CheckForMCA = + StartWait Shell $(UtilityInf), MCAFindBus, $(EE16_1BYTE), $(EE16_2BYTE) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto CheckForISA endif ifstr $($R0) != "NO_ERROR" goto CheckForISA endif ifstr(i) $($R1) == {} set Error = $(CANNOT_FIND_ANY_CARD) set CommonStatus = USER_CANCEL set from = "end" goto nonfatal endif set AdapterList = $($R1) goto skipoptions CheckForISA = + Shell $(ParamInf) Param_QueryCard $(!STF_NCDETCARD) EndWait Ifstr(i) $($R0) != STATUS_SUCCESSFUL Goto adaptersetup Endif Set DetectedParams = $($R1) Shell $(ParamInf) Param_SetDefaults $(DetectedParams) goto adaptersetup configureadapter = + ifstr(i) $(Option) == "ATEAMADAPTER" Ifstr $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE goto fatalregistry Endif Endif GetRegValue $(KeyProduct),"ServiceName", AdapterServiceKey set AdapterServiceKey = *($(AdapterServiceKey),4) LoadLibrary "Intel EtherExpress PRO Adapter Driver Disk" $(!STF_WINDOWSSYSPATH)\epro100.dll DllLibHandle LibraryProcedure DllExitStr $(DllLibHandle) AftCM FreeLibrary $(DllLibHandle) ifstr(i) $(DllExitStr) == "nochange" CloseRegKey $(AdapterServiceKey) CloseRegKey $(KeyProduct) set CommonStatus = STATUS_NO_EFFECT goto successful endif Ifstr $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component product key" goto fatalregistry Endif Endif Debug-Output "INF: Shelling to FindService" Shell $(UtilityInf) FindService, $(KeyProduct) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "INF: FindService shell failure" Goto ShellCodeError Endif Ifstr(i) $($R0) != NO_ERROR Debug-Output "INF: FindService Shell error: "$($R0) Goto fatalregistry endif Set KeyParameters = $($R2) CloseRegKey $($R1) Ifstr $(KeyParameters) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component service" goto fatalregistry endif set OldVersionExisted = $(TRUE) set ValueName = "" set ValueData = "" set ValueStr = "" set ValueList = {} EnumRegValue $(KeyParameters) ValueList ForListDo $(ValueList) set ValueItem = $($) set ValueName = *($(ValueItem),1) set ValueData = *($(ValueItem),4) Ifstr(i) $(ValueName) == "CheckTime" set CheckTimeValue = $(ValueData) else-ifstr(i) $(ValueName) == "DisableTime" set DisableTimeValue = $(ValueData) else-ifstr(i) $(ValueName) == "IdleTime" set IdleTimeValue = $(ValueData) else-ifstr(i) $(ValueName) == "ProbeTime" set ProbeTimeValue = $(ValueData) endif EndForListDo Shell $(ParamInf) Param_SaveValues Set CurrParamSettings = $($R0) goto writeparameters endif Ifstr $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE goto fatalregistry Endif Endif GetRegValue $(KeyProduct),"ServiceName", AdapterServiceKey set AdapterServiceKey = *($(AdapterServiceKey),4) Shell $(UtilityInf) FindService, $(KeyProduct) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Endif Ifstr(i) $($R0) != NO_ERROR Goto fatalregistry endif Set KeyParameters = $($R2) CloseRegKey $($R1) Ifstr $(KeyParameters) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE goto fatalregistry endif set OldVersionExisted = $(TRUE) set ValueName = "" set ValueData = "" set ValueStr = "" set ValueList = {} ifstr(i) $(Option) == "E100BEXP" goto RunProset goto successful RunProset = + RunProgram ExitCode "" "" $(!STF_WINDOWSSYSPATH)\$(ExeName).EXE $(AdapterServiceKey) Ifstr(i) $(!NTN_InstallMode) != configure ifint $(ExitCode) == 20 set Option = "ATEAMADAPTER" goto install_ateam endif ifint $(ExitCode) >= 2 set CommonStatus = STATUS_USERCANCEL goto abandon endif else ifint $(ExitCode) == 0 set CommonStatus = STATUS_NO_EFFECT endif ifint $(ExitCode) == 2 set CommonStatus = STATUS_NO_EFFECT endif ifint $(ExitCode) == 20 set Option = "ATEAMADAPTER" goto install_ateam endif endif goto successful adaptersetup = + Shell "" DebugConfiguration "before displaying dialog" Shell "" DebugConfiguration "After List Translation" Shell $(ParamInf) Param_ParameterConfidence Ifstr(i) $($R0) != STATUS_SUCCESSFUL Goto adapteroptions Endif Ifstr(i) $(DetectedCard) == TRUE Ifstr(i) $(!STF_INSTALL_MODE) != CUSTOM Goto adapterverify Endif Endif adapteroptions = + Set from = adapteroptions adapterverify = + ifcontains(i) $(m_WinNTVersion) not-in {"3.50", "3.51"} Goto skipoptions endif Shell "" DebugConfiguration "after running dialog" Ifstr(i) $(DetectedCard) != TRUE Goto skipoptions Endif Shell $(ParamInf) Param_VerifyCard $(!STF_NCDETCARD) Ifstr(i) $($R0) == STATUS_SUCCESSFUL Goto skipoptions Endif Set from = adapteroptions Set to = skipoptions Shell $(UtilityInf),RegistryErrorString,VERIFY_WARNING ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto Warning install_ateam = + ifcontains(i) $(m_WinNTVersion) in {"3.50", "3.51"} Shell "Subroutn.Inf" SetupMessage $(!STF_LANGUAGE) "NONFATAL" "This feature requires Windows NT 4.0 and higher." goto end endif set CheckTimeValue = 1000 set DisableTimeValue = 8000 set IdleTimeValue = 2000 set ProbeTimeValue = 1000 OpenRegKey $(!REG_H_LOCAL) "" $(ProductATeamKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) CloseRegKey $(KeyProduct) Debug-Output "OEMSETUP.INF: AddSoftwareComponent: ATEAM Miniport" Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), $(ProductATeamSoftwareName), $(ProductATeamSoftwareName), + $(ProductATeamSoftwareTitle), $(STF_CONTEXTINFNAME), $(ProductATeamSoftwareImagePath), + "kernel", "NDIS", {}, "", $(NetEventDLL) Set OEM_ABANDON_SOFTWARE = TRUE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) set KeyProduct = $($R1) Set SoftNetRulesKey = $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add software components" CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = { {SoftwareType, $(NoTitle), $(!REG_VT_SZ), $(ATeamSoftwareType)},+ {MajorVersion, $(NoTitle), $(!REG_VT_DWORD), $(ProductATeamMajorVersion)},+ {MinorVersion, $(NoTitle), $(!REG_VT_DWORD), $(ProductATeamMinorVersion)},+ {Title, $(NoTitle), $(!REG_VT_SZ), $(ProductATeamSoftwareTitle)},+ {Description, $(NoTitle), $(!REG_VT_SZ), $(ProductATeamSoftwareDescription)},+ {ServiceName, $(NoTitle), $(!REG_VT_SZ), $(ProductATeamSoftwareName)},+ {InstallDate, $(NoTitle), $(!REG_VT_DWORD), *($(Now),1)} } Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add value list." CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = { {type, $(NoTitle), $(!REG_VT_SZ), $(NetRuleATeamSoftwareType)},+ {use, $(NoTitle), $(!REG_VT_SZ), $(NetRuleATeamSoftwareUse)}, + {bindform, $(NoTitle), $(!REG_VT_SZ), $(NetRuleATeamSoftwareBindForm)}, + {class, $(NoTitle), $(!REG_VT_MULTI_SZ), $(NetRuleATeamSoftwareClass)}, + {bindable, $(NoTitle), $(!REG_VT_MULTI_SZ), $(NetRuleATeamSoftwareBindable)}, + {InfOption,$(NoTitle), $(!REG_VT_SZ), $(Option)} } Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Resgitry error: add value list." goto fatalregistry endif else CloseRegKey $(KeyProduct) endif OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductATeamTransportName)"\CurrentVersion" $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) CloseRegKey $(KeyProduct) Debug-Output "OEMSETUP.INF: AddSoftwareComponent: ATEAM Transport" Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), $(ProductATeamTransportName), $(ProductATeamTransportName), + $(ProductATeamTransportTitle), $(STF_CONTEXTINFNAME), $(ProductATeamSoftwareImagePath), + "transport", "Transport", {}, "", $(NetEventDLL) Set OEM_ABANDON_SOFTWARE = TRUE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) set KeyProduct = $($R1) Set SoftNetRulesKey = $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add software components" CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = { {SoftwareType, $(NoTitle), $(!REG_VT_SZ), "transport" }, + {MajorVersion, $(NoTitle), $(!REG_VT_DWORD), $(ProductATeamMajorVersion)},+ {MinorVersion, $(NoTitle), $(!REG_VT_DWORD), $(ProductATeamMinorVersion)},+ {Title, $(NoTitle), $(!REG_VT_SZ), $(ProductATeamTransportTitle)},+ {Description, $(NoTitle), $(!REG_VT_SZ), $(ProductATeamTransportDescription)},+ {ServiceName, $(NoTitle), $(!REG_VT_SZ), $(ProductATeamTransportName)},+ {InstallDate, $(NoTitle), $(!REG_VT_DWORD), *($(Now),1)} + {Review, $(NoTitle), $(!REG_VT_DWORD), 1 }, + {OperationsSupport, $(NoTitle), $(!REG_VT_DWORD), 128} } Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add value list." CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = { {type, $(NoTitle), $(!REG_VT_SZ), $(NetRuleATeamTransportType)},+ {use, $(NoTitle), $(!REG_VT_SZ), $(NetRuleATeamTransportUse)}, + {bindform, $(NoTitle), $(!REG_VT_SZ), $(NetRuleATeamTransportBindForm)}, + {class, $(NoTitle), $(!REG_VT_MULTI_SZ), $(NetRuleATeamTransportClass)}, + {bindable, $(NoTitle), $(!REG_VT_MULTI_SZ), $(NetRuleATeamTransportBindable)}, + {InfOption, $(NoTitle), $(!REG_VT_SZ), $(Option)}} Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Resgitry error: add value list." goto fatalregistry endif else CloseRegKey $(KeyProduct) endif Debug-Output "OEMSETUP.INF: AddHardwareComponent ATEAM" Shell $(UtilityInf), AddHardwareComponent, $(ProductATeamHardwareName),$(STF_CONTEXTINFNAME),$(ProductATeamKeyName) set AftRegKeyName = $($R5) ifint $($R4) != -1 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)) endif ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "Cannot add hardware component" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add hardware component" CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) goto fatalregistry endif set KeyParameters = $($R3) set KeyAdapterRules = $($R2) set AdapterNumber = $($R4) set NewValueList = { {Manufacturer, $(NoTitle), $(!REG_VT_SZ), $(Manufacturer)},+ {Title, $(NoTitle), $(!REG_VT_SZ), "["$($R4)"] "$(ProductATeamHardwareTitle)},+ {Description, $(NoTitle), $(!REG_VT_SZ), $(ProductATeamHardwareDescription)},+ {ProductName, $(NoTitle), $(!REG_VT_SZ), $(ProductATeamHardwareName)},+ {ServiceName, $(NoTitle), $(!REG_VT_SZ), $($R5)},+ {InstallDate, $(NoTitle), $(!REG_VT_DWORD),*($(Now),1)} } Shell $(UtilityInf), AddValueList, $($R1), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif CloseRegKey $($R1) set TempProdName = """"$(ProductATeamHardwareName)$(AdapterNumber)"""" set TempBindForm = $(TempProdName)$(NetRuleATeamHardwareBindForm) set NewValueList = { {type, $(NoTitle), $(!REG_VT_SZ), $(NetRuleATeamHardwareType)},+ {bindform, $(NoTitle), $(!REG_VT_SZ), $(TempBindForm)}, + {class, $(NoTitle), $(!REG_VT_MULTI_SZ), $(NetRuleATeamHardwareClass)}, + {InfOption, $(NoTitle), $(!REG_VT_SZ), $(Option)}} Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Resgitry error: add value list." CloseRegKey $(KeyParameters) CloseRegKey $(KeyAdapterRules) goto fatalregistry endif CloseRegKey $(KeyAdapterRules) Set TeamTypeValue = $(ProductSoftwareName) Set NewValueList = {+ {CheckTime, $(NoTitle), $(!REG_VT_DWORD), $(CheckTimeValue)},+ {DisableTime, $(NoTitle), $(!REG_VT_DWORD), $(DisableTimeValue)},+ {IdleTime, $(NoTitle), $(!REG_VT_DWORD), $(IdleTimeValue)},+ {ProbeTime, $(NoTitle), $(!REG_VT_DWORD), $(ProbeTimeValue)},+ {TeamType, $(NoTitle), $(!REG_VT_SZ), $(TeamTypeValue)},+ } Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList) LoadLibrary "Intel EtherExpress PRO Adapter Driver Disk" $(!STF_WINDOWSSYSPATH)\epro100.dll DllLibHandle LibraryProcedure DllExitStr $(DllLibHandle) AftCM FreeLibrary $(DllLibHandle) goto writeparameters skipoptions = + ifstr(i) $(Option) == "ATEAMADAPTER" goto install_ateam endif ifint $(OldVersionExisted) == $(TRUE) ifstr(i) $(!NTN_InstallMode) == configure goto writeparameters endif endif StartWait ifint $(OldVersionExisted) == $(FALSE) ifstr(i) $(!NTN_InstallMode) == "install" Ifstr(i) $(DoCopy) == "YES" Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) Endif install "Install-Option" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal endif endif ifcontains(i) $(m_WinNTVersion) in {"3.50", "3.51"} Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), + $(ProductSoftwareName), + $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), + $(ProductSoftwareImagePathNDIS3), "kernel", "NDIS", {}, "",+ $(NetEventDLL) else Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), + $(ProductSoftwareName), + $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), + $(ProductSoftwareImagePathNDIS4), "kernel", "NDIS", {}, "",+ $(NetEventDLL) endif Set OEM_ABANDON_SOFTWARE = TRUE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) set KeyProduct = $($R1) Set SoftNetRulesKey = $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+ {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+ {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+ {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+ {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, + {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, + {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait goto fatalregistry endif endif set NTDetected = $(TRUE) set Vendor = 32902 set CFID = 4649 ifcontains(i) $(m_WinNTVersion) in {"3.50", "3.51"} Shell "", FindPciE100B else Shell $(UtilityInf), GetPCIInformation, $(Vendor) $(CFID) endif ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R0) == {} Shell "Subroutn.Inf" SetupMessage $(!STF_LANGUAGE) "FATAL" "Setup was unable to detect an Intel EtherExpress PRO Adapter in your system. Install the adapter and try again." goto setfailed endif set AdapterList = $($R0) Shell "", FindOutdatedRegistryEntries ifint $($R0) == -1 LoadLibrary "Intel EtherExpress PRO Adapter Driver Disk" $(!STF_WINDOWSSYSPATH)\epro100.dll DllLibHandle LibraryProcedure DllExitStr $(DllLibHandle) AddSlots FreeLibrary $(DllLibHandle) endif ForListDo $(AdapterList) Set InstallCard = "YES" ifint $(NTDetected) == $(TRUE) set DetectedBusNum = *($($),1) set DetectedSlotNum = *($($),2) Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(DetectedBusNum), + $(DetectedSlotNum), $(ProductHardware$(Option)Description), $(ProductHardwareName) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr $($R0) != "NO_ERROR" set Error = $($R0) goto fatal endif ifstr(i) $($R1) == "YES" set InstallCard = "NO" endif endif ifstr(i) $(InstallCard) == "NO" set detmsg = "An "$(ProductHardwareTitle)" at PCI Bus "$(DetectedBusNum)" PCI Slot "$(DetectedSlotNum)" is already installed!" goto det_bypass else Debug-Output "*** Installing E100B at $(DetectedBusNum):$(DetectedSlotNum)!" Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName) ifint $($R4) != -1 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)) endif ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR" EndWait CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) goto fatalregistry endif Set MyNetCardKey = $($R1) Set MyNetRuleKey = $($R2) Set MyParameterKey = $($R3) set AdapterNumber = $($R4) set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+ {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+ {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(MyNetCardKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set BusNumber = $(DetectedBusNum) set SlotNum = $(DetectedSlotNum) OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(!REG_KEY_READ) KeyWinNT ifstr(i) $(KeyWinNT) != "" GetRegValue $(KeyWinNT) "CurrentVersion" CurrentVersionValue endif CloseRegKey $(KeyWinNT) set m_WinNTVersion = *($(CurrentVersionValue),4) Debug-Output "Setting PerfOpts Defaults 3.51" Ifstr(i) $(!STF_PROCESSOR) == "I586" Debug-Output "Found Pentium" set myPerfOptimsValue = 2 else Debug-Output "Found nonPentium" set myPerfOptimsValue = 0 endif ifcontains(i) $(m_WinNTVersion) not-in {"3.50", "3.51"} Debug-Output "Setting PerfOpts for NT 4.X" Ifstr(i) $(!STF_PROCESSOR) == "I586" Debug-Output "Found Pentium" set myPerfOptimsValue = 2 else Debug-Output "Found nonPentium" set myPerfOptimsValue = 0 endif endif Set NewValueList = {+ {Adaptive_IFS, $(NoTitle), $(!REG_VT_DWORD), 1}, + {BusNumber, $(NoTitle), $(!REG_VT_DWORD), $(BusNumber)},+ {BusType, $(NoTitle), $(!REG_VT_DWORD), 5)},+ {BusTypeLocal, $(NoTitle), $(!REG_VT_DWORD), 5}, + {ForceDpx, $(NoTitle), $(!REG_VT_DWORD), 0}, + {MapRegisters, $(NoTitle), $(!REG_VT_DWORD), 64}, + {MediaType, $(NoTitle), $(!REG_VT_DWORD), 1 },+ {MsPciScan, $(NoTitle), $(!REG_VT_DWORD), 1 },+ {NumCoalesce, $(NoTitle), $(!REG_VT_DWORD), 8}, + {NumRfd, $(NoTitle), $(!REG_VT_DWORD), 16}, + {NumTbdPerTcb, $(NoTitle), $(!REG_VT_DWORD), 12}, + {NumTcb, $(NoTitle), $(!REG_VT_DWORD), 16}, + {PerfOptims, $(NoTitle), $(!REG_VT_DWORD), $(myPerfOptimsValue)},+ {RxDmaCount, $(NoTitle), $(!REG_VT_DWORD), 0}, + {RxFifo, $(NoTitle), $(!REG_VT_DWORD), 8}, + {SlotNumber, $(NoTitle), $(!REG_VT_DWORD), $(SlotNum)},+ {Speed, $(NoTitle), $(!REG_VT_DWORD), 0}, + {Threshold, $(NoTitle), $(!REG_VT_DWORD), 16}, + {TxDmaCount, $(NoTitle), $(!REG_VT_DWORD), 0}, + {TxFifo, $(NoTitle), $(!REG_VT_DWORD), 8}, + {Txmitwait, $(NoTitle), $(!REG_VT_DWORD), 1}, + {UcodeSW, $(NoTitle), $(!REG_VT_DWORD), 1}, + {UnderrunRetry, $(NoTitle), $(!REG_VT_DWORD), 1}, + } Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)" Shell $(UtilityInf), AddValueList, $(MyParameterKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)"""" set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm) set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+ {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Debug-Output "$(InfFile) $(Option): HardwareRuleKey = $(NewValueList)" Shell $(UtilityInf), AddValueList, $(MyNetRuleKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif CloseRegKey $(MyNetCardKey) CloseRegKey $(MyNetRuleKey) endif det_bypass = + EndForListDo goto writeparameters writeparameters = + ifstr(i) $(Option) == "ATEAMADAPTER" Set NewValueList = {+ {CheckTime, $(NoTitle), $(!REG_VT_DWORD), $(CheckTimeValue)},+ {DisableTime, $(NoTitle), $(!REG_VT_DWORD), $(DisableTimeValue)},+ {IdleTime, $(NoTitle), $(!REG_VT_DWORD), $(IdleTimeValue)},+ {ProbeTime, $(NoTitle), $(!REG_VT_DWORD), $(ProbeTimeValue)},+ } Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList) ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" Shell $(UtilityInf),AddDefaultNetCardParameters,$(KeyParameters) endif CloseRegKey $(KeyParameters) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "Registry error: Add value list" goto fatalregistry endif goto successful endif Shell $(UtilityInf), GetBusTypeNum set BusTypeNum = $($R1) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif Set IOAddrValue = *($(IOAddrValues), ~($(IOAddrList),$(IOAddrValue))) Shell "" DebugConfiguration "Before Writing Parameters" set NewValueList = {{Eid,$(NoTitle),$(!REG_VT_DWORD),0)}} OpenRegKey $(!REG_H_LOCAL) "" $(PROSetKeyName)"\"Adapters $(MAXIMUM_ALLOWED) PROSetAdapterKey ifstr $(PROSetAdapterKey) == $(KeyNull) CreateRegKey $(!REG_H_LOCAL) {$(PROSetKeyName)"\"Adapters,0,GenericClass} "" + $(MAXIMUM_ALLOWED) "" PROSetAdapterKey ifstr $(PROSetAdapterKey) == $(KeyNull) Shell "Subroutn.Inf" SetupMessage $(!STF_LANGUAGE) "NONFATAL" CreateRegAdapterFailed goto fatalregistry endif endif set NewValueList = {{$(PROSetAdapterName),$(NoTitle), $(!REG_VT_SZ), $(Adapter)}} Shell $(UtilityInf), AddValueList, $(PROSetAdapterKey), $(NewValueList) CloseRegKey $(PROSetAdapterKey) OpenRegKey $(!REG_H_LOCAL) "" $(PROSetKeyName)"\"$(PROSetAdapterName) $(MAXIMUM_ALLOWED) PROSetAdapterKey ifstr $(PROSetAdapterKey) == $(KeyNull) CreateRegKey $(!REG_H_LOCAL) {$(PROSetKeyName)"\"$(PROSetAdapterName),0,GenericClass} "" + $(MAXIMUM_ALLOWED) "" PROSetAdapterKey ifstr $(PROSetAdapterKey) == $(KeyNull) Shell "Subroutn.Inf" SetupMessage $(!STF_LANGUAGE) "NONFATAL" CreateRegEPRO10Failed goto fatalregistry endif endif set NewValueList = {{Configure,$(NoTitle),$(!REG_VT_SZ),$(Configure)},+ {Detect,$(NoTitle),$(!REG_VT_SZ),$(Detect)},+ {Diagnose,$(NoTitle),$(!REG_VT_SZ),$(Diagnose)},+ {DLL,$(NoTitle),$(!REG_VT_SZ),$(DLL)},+ {Help,$(NoTitle),$(!REG_VT_SZ),$(Help)},+ {RegistryKey,$(NoTitle),$(!REG_VT_SZ),$(RegistryKey)},+ {AdapterDescription,$(NoTitle),$(!REG_VT_SZ),$(AdapterDescription)},+ {InstallAnyway,$(NoTitle),$(!REG_VT_SZ),$(InstallAnyway)},+ {DeviceExist,$(NoTitle),$(!REG_VT_SZ),$(DeviceExist)},+ {GetExtendedFeatures,$(NoTitle),$(!REG_VT_SZ),$(GetExtendedFeatures)},+ {Summary,$(NoTitle),$(!REG_VT_SZ),$(Summary)}} Shell $(UtilityInf), AddValueList, $(PROSetAdapterKey), $(NewValueList) CloseRegKey $(PROSetAdapterKey) OpenRegKey $(!REG_H_LOCAL) "" $(PROSetKeyName)"\"$(PROSetAdapterName)"\"$(PROSetParameters) $(MAXIMUM_ALLOWED) PROSetAdapterKey ifstr $(PROSetAdapterKey) == $(KeyNull) CreateRegKey $(!REG_H_LOCAL) {$(PROSetKeyName)"\"$(PROSetAdapterName)"\"$(PROSetParameters),0,GenericClass} "" + $(MAXIMUM_ALLOWED) "" PROSetAdapterKey ifstr $(PROSetAdapterKey) == $(KeyNull) Shell "Subroutn.Inf" SetupMessage $(!STF_LANGUAGE) "NONFATAL" CreateRegEPRO10Failed goto fatalregistry endif endif set NewValueList = { + {BusNumber,$(NoTitle),$(!REG_VT_SZ),$(BusNumber)}, + {BusType,$(NoTitle),$(!REG_VT_SZ),$(BusType)}, + {BusTypeLocal,$(NoTitle),$(!REG_VT_SZ),$(BusTypeLocal)}, + {Eid,$(NoTitle),$(!REG_VT_SZ),$(Eid)}, + {Fifo,$(NoTitle),$(!REG_VT_SZ),$(Fifo)}, + {ForceDpx,$(NoTitle),$(!REG_VT_SZ),$(ForceDpx)}, + {MapRegisters,$(NoTitle),$(!REG_VT_SZ),$(MapRegisters)}, + {MediaType,$(NoTitle),$(!REG_VT_SZ),$(MediaType)}, + {MsPciScan,$(NoTitle),$(!REG_VT_SZ),$(MsPciScan)}, + {NumCoalesce,$(NoTitle),$(!REG_VT_SZ),$(NumCoalesce)}, + {NumRfd,$(NoTitle),$(!REG_VT_SZ),$(NumRfd)}, + {NumTbd,$(NoTitle),$(!REG_VT_SZ),$(NumTbd)}, + {NumTbdPerTcb,$(NoTitle),$(!REG_VT_SZ),$(NumTbdPerTcb)}, + {NumTcb,$(NoTitle),$(!REG_VT_SZ),$(NumTcb)}, + {Off,$(NoTitle),$(!REG_VT_SZ),$(Off)}, + {On,$(NoTitle),$(!REG_VT_SZ),$(On)}, + {RxDmaCount,$(NoTitle),$(!REG_VT_SZ),$(RxDmaCount)}, + {RxFifo,$(NoTitle),$(!REG_VT_SZ),$(RxFifo)}, + {Slot,$(NoTitle),$(!REG_VT_SZ),$(Slot)}, + {Speed,$(NoTitle),$(!REG_VT_SZ),$(Speed)}, + {Threshold,$(NoTitle),$(!REG_VT_SZ),$(Threshold)}, + {TxDmaCount,$(NoTitle),$(!REG_VT_SZ),$(TxDmaCount)}, + {TxFifo,$(NoTitle),$(!REG_VT_SZ),$(TxFifo)}, + {UnderrunRetry,$(NoTitle),$(!REG_VT_SZ),$(UnderrunRetry)}, + {PerfOptims,$(NoTitle),$(!REG_VT_SZ),$(PerfOptims)}, + {UcodeSW,$(NoTitle),$(!REG_VT_SZ),$(UcodeSW)}, + {Adaptive_IFS,$(NoTitle),$(!REG_VT_SZ),$(Adaptive_IFS)}, + {Txmitwait,$(NoTitle),$(!REG_VT_SZ),$(Txmitwait)}, + } Shell $(UtilityInf), AddValueList, $(PROSetAdapterKey), $(NewValueList) CloseRegKey $(PROSetAdapterKey) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif EndWait ifstr(i) $(!NTN_Origination) == "INSTALL" ifstr(i) $(!STF_GUI_UNATTENDED) == YES RunProgram DummyExitCode "" "" $(!STF_WINDOWSSYSPATH)\$(ExeName).EXE /BATCH $(AdapterServiceKey) else RunProgram DummyExitCode "" "" $(!STF_WINDOWSSYSPATH)\$(ExeName).EXE $(AdapterServiceKey) endif endif Ifstr(i) $(!NTN_InstallMode) != configure ifint $(ExitCode) >= 2 set CommonStatus = STATUS_USERCANCEL goto abandon endif else ifint $(ExitCode) == 0 set CommonStatus = STATUS_NO_EFFECT endif ifint $(ExitCode) == 2 set CommonStatus = STATUS_NO_EFFECT endif endif goto successful bindingadapter = + ifstr(i) $(Option) == "ATEAMADAPTER" debug-output "set Services\iAFTProtocol\type = 4" OpenRegKey $(!REG_H_LOCAL) "" $(ServicesBaseName)"\"$(ProductATeamTransportName) $(MAXIMUM_ALLOWED) TransportKey Ifstr $(TransportKey) == $(KeyNull) debug-output "cannot open Services\iAFTProtocol\type " else Set NewValueList = {Type, $(NoTitle), $(!REG_VT_DWORD), 4 } SetRegValue $(TransportKey) $(NewValueList) CloseRegKey $(TransportKey) endif OpenRegKey $(!REG_H_LOCAL) "" $(ServicesBaseName)"\"$(ProductATeamSoftwareName)"\Linkage" $(MAXIMUM_ALLOWED) LinkageKey Ifstr $(LinkageKey) == $(KeyNull) debug-output "cannot open Services\iAFT\Linkage " else debug-output "Read iAFT linkage " GetRegValue $(LinkageKey) "Bind" BindList debug-output "BindList = "$(BindList) set AdapterList = *($(BindList),4) debug-output "AdapterList = "$(AdapterList) CloseRegKey $(LinkageKey) ForListDo $(AdapterList) debug-output "Adapter = "$($) Split-String $($), "\", Adapter QueryListSize ListSize $(Adapter) set mspaName = *($(Adapter),$(ListSize)) debug-output "MultiSpan Miniport Name ="$(mspaName) EndForListDo OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\iAFTProtocol\Linkage" $(MAXIMUM_ALLOWED) LinkageKey ifstr $(LinkageKey) != $(KeyNull) GetRegValue $(LinkageKey) "Bind" BindList debug-output "BindList = "$(BindList) set AdapterList = *($(BindList),4) debug-output "AdapterList = "$(AdapterList) set CardNumber = 0 set NewBindList = {} set NewBindDisableList = {} ForListDo $(AdapterList) debug-output "Adapter = "$($) Split-String $($), "\", Adapter QueryListSize ListSize $(Adapter) set CardName = *($(Adapter),$(ListSize)) debug-output "CardName="$(CardName) ifstr(i) $(CardName) == $(iAFTProtocolName) debug-output "ERROR!!!!! bind to itself " set NewBindDisableList = >($(NewBindDisableList), $($)) else set NewBindList = >($(NewBindList), $($)) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(CardName)"\Parameters" $(MAXIMUM_ALLOWED) ParamKey Ifstr $(ParamKey) == $(KeyNull) debug-output "cannot open "$(CardName)"\Parameters" else OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(CardName)"\Parameters\iAFTProtocol" $(MAXIMUM_ALLOWED) KeyiAFTProtocol Ifstr $(KeyiAFTProtocol) == $(KeyNull) debug-output "cannot open "$(CardName)"\Parameters\iAFTProtocol, CreateRegKey" CreateRegKey $(ParamKey) { "iAFTProtocol" , 0, GenericClass } "" + $(!REG_KEY_SET_VALUE) "" KeyiAFTProtocol Ifstr $(KeyiAFTProtocol) == $(KeyNull) debug-output "CreateRegKey ERROR!!" Endif else debug-output "Key exist!!" endif debug-output "Connect="$(mspaName)" Number="$(CardNumber) SetRegValue $(KeyiAFTProtocol) {"Connect",$(NoTitle),$(!REG_VT_SZ), $(mspaName)} SetRegValue $(KeyiAFTProtocol) {"Number", $(NoTitle),$(!REG_VT_DWORD),$(CardNumber)} set-add CardNumber = $(CardNumber) , 1 CloseRegKey $(KeyiAFTProtocol) CloseRegKey $(ParamKey) endif endif EndForListDo CloseRegKey $(LinkageKey) endif endif Shell "", PruneLoopbackBinding, "iAFTProtocol", "iAFT" set AFTStartNum = 1 AFT_jmp = + Shell $(UtilityInf), FindNextNetworkCard, "iAFT", $(AFTStartNum) ifstr $($R0) != $(KeyNull) GetRegValue $($R0) "ServiceName" ValueList set AFTTargetService = *($(ValueList),4) CloseRegKey $($R0) set AFTStartNum = $($R1) Shell "", EnableDisableBindings, "iVLANProtocol", "\Device\"$(AFTTargetService), "disable" Shell "", EnableDisableBindings, "iAFTProtocol", "\Device\"$(AFTTargetService), "disable" goto AFT_jmp else ifint $(AFTStartNum) != "10" set-add AFTStartNum = $(AFTStartNum), 1 goto AFT_jmp endif endif set AFTstartnum = "1" BA_AFTjmp2 = + Shell $(UtilityInf), FindNextNetworkCard, "e100b", $(AFTstartnum) ifstr $($R0) != $(KeyNull) GetRegValue $($R0) "ServiceName" ValueList set BA_AFTTargetService = *($(ValueList),4) CloseRegKey $($R0) set AFTstartnum = $($R1) Shell $(UtilityInf), FindService, $(BA_AFTTargetService), "adapter" ifstr $($R0) != $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(BA_AFTTargetService)"\Parameters\iAFTProtocol" $(MAXIMUM_ALLOWED) BA_AFTProtoKeySvc ifstr $(BA_AFTProtoKeySvc) != $(KeyNull) Shell "", PruneEverything, $(BA_AFTTargetService) Shell "", EnableDisableBindings, "iAFTProtocol", "\Device\"$(BA_AFTTargetService), "activate" else Shell "", EnableDisableBindings, "iAFTProtocol", "\Device\"$(BA_AFTTargetService), "disable" endif endif goto BA_AFTjmp2 else ifint $(AFTstartnum) != "10" set-add AFTstartnum = $(AFTstartnum), 1 goto BA_AFTjmp2 endif endif endif goto successful removeadapter = + Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif else-ifstr(i) $(Option) == "ATEAMADAPTER" OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) RM_AFTVictimiAFTKey Ifstr $(RM_AFTVictimiAFTKey) == $(KeyNull) goto fatalregistry endif GetRegValue $(RM_AFTVictimiAFTKey), "ServiceName", RM_AFTVictimInfo set RM_AFTVictim = *($(RM_AFTVictimInfo), 4) CloseRegKey $(RM_AFTVictimiAFTKey) set EnableBindings = "TRUE" set rm_AFTstartnum = "1" RM_AFTjmp2 = + Shell $(UtilityInf), FindNextNetworkCard, "e100b", $(rm_AFTstartnum) ifstr $($R0) != $(KeyNull) GetRegValue $($R0) "ServiceName" ValueList set RM_AFTTargetService = *($(ValueList),4) CloseRegKey $($R0) set rm_AFTstartnum = $($R1) Shell $(UtilityInf), FindService, $(RM_AFTTargetService), "adapter" ifstr $($R0) != $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(RM_AFTTargetService)"\Parameters\iAFTProtocol" $(MAXIMUM_ALLOWED) RM_AFTProtoKeySvc ifstr $(RM_AFTProtoKeySvc) != $(KeyNull) GetRegValue $(RM_AFTProtoKeySvc) "Connect" ValueList set RM_AFTcurrent = *($(ValueList),4) ifstr $(RM_AFTcurrent) == $(RM_AFTVictim) ifstr(i) $(EnableBindings) == "TRUE" set EnableBindings = "FALSE" Shell $(UtilityInf), FindService, "NetBT", "protocol" ifstr $($R0) != $(KeyNull) Shell "", EnableDisableBindings, "LanmanWorkstation", "\Device\NetBT_"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "LanmanServer", "\Device\NetBT_"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "NetBIOS", "\Device\NetBT_"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "RemoteAccess", "\Device\NetBT_"$(RM_AFTTargetService), "activate" endif Shell $(UtilityInf), FindService, "Nbf", "protocol" ifstr $($R0) != $(KeyNull) Shell "", EnableDisableBindings, "LanmanWorkstation", "\Device\Nbf_"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "LanmanServer", "\Device\Nbf_"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "NetBIOS", "\Device\Nbf_"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "RemoteAccess", "\Device\Nbf_"$(RM_AFTTargetService), "activate" endif Shell "", EnableDisableBindings, "Nbf", "\Device\"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "NwlnkIpx", "\Device\"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "Tcpip", "\Device\"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "AppleTalk", "\Device\"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "NetBT", "\Device\"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "bh", "\Device\"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "DLC", "\Device\"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "Streams", "\Device\"$(RM_AFTTargetService), "activate" Shell "", EnableDisableBindings, "iAFTProtocol", "\Device\"$(RM_AFTTargetService), "disable" CloseRegKey $(RM_AFTProtoKeySvc) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(RM_AFTTargetService)"\Parameters\" $(MAXIMUM_ALLOWED) RM_AFTProtoKeySvc2 DeleteRegKey $(RM_AFTProtoKeySvc2) "iAFTProtocol" CloseRegKey $(RM_AFTProtoKeySvc2) endif endif endif endif goto RM_AFTjmp2 else ifint $(rm_AFTstartnum) != "10" set-add rm_AFTstartnum = $(rm_AFTstartnum), 1 goto RM_AFTjmp2 endif endif Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), $(ProductATeamHardwareName), $(!NTN_RegBase) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\"$(ProductATeamSoftwareName) $(MAXIMUM_ALLOWED) Rm_AFTServiceKey Ifstr $(Rm_AFTServiceKey) == $(KeyNull) Debug-Output "RemoveService iAFTProtocol" Shell $(UtilityInf), RemoveService,$(ProductATeamTransportName), "NO" Debug-Output "RemoveSoftwareComponent iAFTProtocol" Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), $(ProductATeamTransportName) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif else GetRegValue $(Rm_AFTServiceKey) "DeleteFlag" ValueList ifint $(RegLastError) == $(!REG_ERROR_SUCCESS) set RM_AFTflagpresent = *($(ValueList),4) ifstr $(RM_AFTflagpresent) == "1" Debug-Output "RemoveService iAFTProtocol" Shell $(UtilityInf), RemoveService,$(ProductATeamTransportName), "NO" Debug-Output "RemoveSoftwareComponent iAFTProtocol" Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), $(ProductATeamTransportName) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif endif endif CloseRegKey $(Rm_AFTServiceKey) goto end else Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), $(ProductSoftwareName), $(!NTN_RegBase) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif endif endif goto end UpgradeSoftware = + OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set !UG_Filename = $($R0) install "Install-Update" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS goto fatal endif OpenRegKey $(!REG_H_LOCAL) "" $(PROSetKeyName)"\"Adapters $(MAXIMUM_ALLOWED) PROSetAdapterKey ifstr $(PROSetAdapterKey) == $(KeyNull) CreateRegKey $(!REG_H_LOCAL) {$(PROSetKeyName)"\"Adapters,0,GenericClass} "" + $(MAXIMUM_ALLOWED) "" PROSetAdapterKey ifstr $(PROSetAdapterKey) == $(KeyNull) Shell "Subroutn.Inf" SetupMessage $(!STF_LANGUAGE) "NONFATAL" CreateRegAdapterFailed goto fatalregistry endif endif set NewValueList = {{$(PROSetAdapterName),$(NoTitle), $(!REG_VT_SZ), $(Adapter)}} Shell $(UtilityInf), AddValueList, $(PROSetAdapterKey), $(NewValueList) CloseRegKey $(PROSetAdapterKey) OpenRegKey $(!REG_H_LOCAL) "" $(PROSetKeyName)"\"$(PROSetAdapterName) $(MAXIMUM_ALLOWED) PROSetAdapterKey ifstr $(PROSetAdapterKey) == $(KeyNull) CreateRegKey $(!REG_H_LOCAL) {$(PROSetKeyName)"\"$(PROSetAdapterName),0,GenericClass} "" + $(MAXIMUM_ALLOWED) "" PROSetAdapterKey ifstr $(PROSetAdapterKey) == $(KeyNull) Shell "Subroutn.Inf" SetupMessage $(!STF_LANGUAGE) "NONFATAL" CreateRegEPRO10Failed goto fatalregistry endif endif set NewValueList = {{Configure,$(NoTitle),$(!REG_VT_SZ),$(Configure)},+ {Detect,$(NoTitle),$(!REG_VT_SZ),$(Detect)},+ {Diagnose,$(NoTitle),$(!REG_VT_SZ),$(Diagnose)},+ {DLL,$(NoTitle),$(!REG_VT_SZ),$(DLL)},+ {Help,$(NoTitle),$(!REG_VT_SZ),$(Help)},+ {RegistryKey,$(NoTitle),$(!REG_VT_SZ),$(RegistryKey)},+ {AdapterDescription,$(NoTitle),$(!REG_VT_SZ),$(AdapterDescription)},+ {InstallAnyway,$(NoTitle),$(!REG_VT_SZ),$(InstallAnyway)},+ {DeviceExist,$(NoTitle),$(!REG_VT_SZ),$(DeviceExist)},+ {GetExtendedFeatures,$(NoTitle),$(!REG_VT_SZ),$(GetExtendedFeatures)},+ {Summary,$(NoTitle),$(!REG_VT_SZ),$(Summary)}} Shell $(UtilityInf), AddValueList, $(PROSetAdapterKey), $(NewValueList) CloseRegKey $(PROSetAdapterKey) Shell "", FindOutdatedRegistryEntries ifint $($R0) == -1 LoadLibrary "Intel EtherExpress PRO Adapter Driver Disk" $(!STF_WINDOWSSYSPATH)\epro100.dll DllLibHandle LibraryProcedure DllExitStr $(DllLibHandle) AddSlots FreeLibrary $(DllLibHandle) endif SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)} SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)} CloseRegKey $(KeyProduct) else goto fatalregistry endif goto end successful = + goto end abandon = + ForListDo $(OEM_ABANDON_OPTIONS) Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $($) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif EndForListDo Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), FALSE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end warning = + Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(to) else-ifstr(i) $($R1) == "CANCEL" goto $(from) else goto "end" endif nonfatalinfo = + Set Severity = STATUS Set CommonStatus = STATUS_USERCANCEL goto nonfatalmsg nonfatal = + Set Severity = NONFATAL goto nonfatalmsg nonfatalmsg = + ifstr(i) $(Error) == "" Set Severity = NONFATAL Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(from) else goto "end" endif fatalregistry = + Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal fataldetect = + Shell $(UtilityInf),RegistryErrorString,CANNOT_DETECT ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal fatal = + ifstr(i) $(Error) == "" Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto setfailed ShellCodeError = + set DlgType = "MessageBox" set STF_MB_TITLE = "Error: "$(FunctionTitle) set STF_MB_TEXT = "Shell Code Error" set STF_MB_TYPE = 1 set STF_MB_ICON = 3 set STF_MB_DEF = 1 ui start "Error Message" goto setfailed setfailed = + set CommonStatus = STATUS_FAILED ifstr(i) $(OEM_ABANDON_ON) == TRUE set OEM_ABANDON_ON = FALSE goto abandon endif goto end end = + goto term term = + Return $(CommonStatus) [BindingsReview] set Option = $($1) set SrcDir = $($2) set AddCopy = $($3) set DoCopy = $($4) set DoConfig = $($5) set Status = $($R0) Return $(Status) [DebugConfiguration] return [Install-Option] set STF_OVERWRITE = VERIFYSOURCEOLDER set STF_VITAL = "" ifstr(i) $(AddCopy) == "YES" ifcontains(i) $(m_WinNTVersion) not-in {"3.50", "3.51"} AddSectionFilesToCopyList Files-N3NDIS4 $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers else AddSectionFilesToCopyList Files-N3NDIS3 $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers endif AddSectionFilesToCopyList Files-Exe $(SrcDir) $(!STF_WINDOWSSYSPATH) AddSectionFilesToCopyList Files-Exe-Drivers $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers endif ifstr(i) $(DoCopy) == "YES" set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList else ifcontains(i) $(m_WinNTVersion) not-in {"3.50", "3.51"} LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\$(Path)$(ExeName).EXE $(!STF_WINDOWSSYSPATH)\$(ExeName).EXE LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\$(Path)$(Sp1Name).DLL $(!STF_WINDOWSSYSPATH)\$(Sp1Name).DLL LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\$(Path)$(ProdHelp).HLP $(!STF_WINDOWSSYSPATH)\$(ProdHelp).HLP LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\$(Path)$(GenHelp).HLP $(!STF_WINDOWSSYSPATH)\$(GenHelp).HLP LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\$(Path)$(DllName).DLL $(!STF_WINDOWSSYSPATH)\$(DllName).DLL LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\$(Path)$(Sp3Name).SYS $(!STF_WINDOWSSYSPATH)\DRIVERS\$(Sp3Name).SYS LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\$(Path)$(KddName).SYS $(!STF_WINDOWSSYSPATH)\DRIVERS\$(KddName).SYS endif endif Exit [Install-Update] set STF_VITAL = "" set STF_OVERWRITE = "VERIFYSOURCEOLDER" ifcontains(i) $(m_WinNTVersion) not-in {"3.50", "3.51"} AddSectionFilesToCopyList Files-N3NDIS4 $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers else AddSectionFilesToCopyList Files-N3NDIS3 $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers endif AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH) AddSectionFilesToCopyList Files-Exe $(SrcDir) $(!STF_WINDOWSSYSPATH) AddSectionFilesToCopyList Files-Exe-Drivers $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exit [FindPciE100B] read-syms GeneralConstants read-syms FileConstants set VendorID = 32902 set DeviceID = 4649 set MultiAdapter = "HARDWARE\Description\System\MultifunctionAdapter" set InfoList = {} OpenRegKey $(!REG_H_LOCAL) "" $(MultiAdapter) $(MAXIMUM_ALLOWED) KeyMultiAdapter Ifstr $(KeyMultiAdapter) == $(KeyNull) goto FindPciE100B_end endif EnumRegKey $(KeyMultiAdapter) BusList set BusNum = 0 set index = 0 ForListDo $(BusList) OpenRegKey $(!REG_H_LOCAL) "" $(MultiAdapter)"\"$(index) $(MAXIMUM_ALLOWED) KeyMultiAdapterBus GetRegValue $(KeyMultiAdapterBus) "Identifier" IdentifierInfo ifstr(i) *($(IdentifierInfo),4) == "PCI" set function = 0 set device = 0 FindPciE100B_again = + ifint $(device) < 32 LibraryProcedure Result, $(!LIBHANDLE), GetPciInformation, $(BusNum), $(device), $(function) ifint *($(Result),1) == $(VendorID) ifint *($(Result),2) == $(DeviceID) set InfoList = >($(InfoList),{$(BusNum),$(device),0}) endif endif Set-add device = $(device),1 goto FindPciE100B_again endif set-add BusNum = $(BusNum),1 endif set-add index = $(index),1 EndForListDo CloseRegKey $(KeyMultiAdapter) FindPciE100B_end = + return $(InfoList) [EnableDisableBindings] read-syms GeneralConstants read-syms FileConstants set m_ServiceName = $($0) set m_BindingString = $($1) set m_Action = $($2) ifstr(i) $(m_Action) == "disable" set m_Linkage = "\Linkage" else set m_Linkage = "\Linkage\Disabled" endif Shell $(UtilityInf), FindService, $(m_ServiceName), "protocol" ifstr $($R0) != $(KeyNull) Set m_BindList = {} OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(m_ServiceName)$(m_Linkage) $(MAXIMUM_ALLOWED) m_KeySvc GetRegValue $(m_KeySvc), "Bind", m_TempList Ifint $(RegLastError) == $(!REG_ERROR_SUCCESS) Set m_BindList = *($(m_TempList),4) set m_found = "FALSE" ForListDo $(m_BindList) ifstr(i) $(m_found) == "FALSE" ifstr(i) $($) == $(m_BindingString) Shell $(UtilityInf), ToggleBinding, $(m_ServiceName), $(#), $(m_Action) set m_found = "TRUE" endif endif EndForListDo Endif CloseRegKey $(m_KeySvc) endif return [FindOutdatedRegistryEntries] read-syms GeneralConstants read-syms FileConstants set ReturnValue = 0 set scanstartnum = "1" RegCheckjmp = + Shell $(UtilityInf), FindNextNetworkCard, "e100b", $(scanstartnum) ifstr $($R0) != $(KeyNull) GetRegValue $($R0) "ServiceName" ValueList set scanTargetService = *($(ValueList),4) Debug-Output "scanTargetService: $(scanTargetService)" CloseRegKey $($R0) set scanstartnum = $($R1) Shell $(UtilityInf), FindService, $(scanTargetService), "adapter" ifstr $($R0) != $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(scanTargetService)"\Parameters" $(MAXIMUM_ALLOWED) scanProtoKeySvc Ifstr $(scanProtoKeySvc) != $(KeyNull) GetRegValue $(scanProtoKeySvc) "Eid" EidValue Ifstr $(EidValue) != $(KeyNull) GetRegValue $(scanProtoKeySvc) "SlotNumber" SlotValue Ifstr $(SlotValue) == $(KeyNull) set ReturnValue = -1 endif endif endif endif goto RegCheckjmp else ifint $(scanstartnum) != "10" set-add scanstartnum = $(scanstartnum), 1 goto RegCheckjmp endif endif return $(ReturnValue) [PruneLoopbackBinding] read-syms GeneralConstants read-syms FileConstants set ProtocolEdgeName = $($0) set MiniportEdgeName = $($1) startpruningloopback = + Set BA_BindList = {} OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(ProtocolEdgeName)"\Linkage" $(MAXIMUM_ALLOWED) BA_KeySvc GetRegValue $(BA_KeySvc), "Bind", TempValue Ifint $(RegLastError) == $(!REG_ERROR_SUCCESS) Set BA_BindList = *($(TempValue),4) Endif set BA_found = "FALSE" ForListDo $(BA_BindList) ifstr(i) $(BA_found) == "FALSE" Split-String $($) "0123456789\" BA_TestItem ifcontains(i) $(MiniportEdgeName) in $(BA_TestItem) Shell $(UtilityInf), ToggleBinding, $(ProtocolEdgeName), $(#), "disable" set BA_AFTfound = "TRUE" endIf endif EndForListDo CloseRegKey $(BA_KeySvc) ifstr(i) $(BA_found) == "TRUE" goto startpruningloopback endif return [PruneEverything] read-syms GeneralConstants read-syms FileConstants set ServiceToBePruned = $($0) Debug-Output "INF: ServiceToBePruned : "$(ServiceToBePruned) Shell $(UtilityInf), FindService, "NetBT", "protocol" ifstr $($R0) != $(KeyNull) Shell "", EnableDisableBindings, "LanmanWorkstation", "\Device\NetBT_"$(ServiceToBePruned), "disable" Shell "", EnableDisableBindings, "LanmanServer", "\Device\NetBT_"$(ServiceToBePruned), "disable" Shell "", EnableDisableBindings, "NetBIOS", "\Device\NetBT_"$(ServiceToBePruned), "disable" Shell "", EnableDisableBindings, "RemoteAccess", "\Device\NetBT_"$(ServiceToBePruned), "disable" endif Shell $(UtilityInf), FindService, "Nbf", "protocol" ifstr $($R0) != $(KeyNull) Shell "", EnableDisableBindings, "LanmanWorkstation", "\Device\Nbf_"$(ServiceToBePruned), "disable" Shell "", EnableDisableBindings, "LanmanServer", "\Device\Nbf_"$(ServiceToBePruned), "disable" Shell "", EnableDisableBindings, "NetBIOS", "\Device\Nbf_"$(ServiceToBePruned), "disable" Shell "", EnableDisableBindings, "RemoteAccess", "\Device\Nbf_"$(ServiceToBePruned), "disable" endif set ServicesStr = "SYSTEM\CurrentControlSet\Services" OpenRegKey $(!REG_H_LOCAL) "" $(ServicesStr) $(MAXIMUM_ALLOWED) ServicesKey Ifstr $(ServicesKey) == $(KeyNull) goto FindPciE100SERVER_end endif EnumRegKey $(ServicesKey) ServicesList ForListDo $(ServicesList) set TempTargetService = *($($),1) ifstr(i) $(TempTargetService) != "E100B" set TargetServiceString = "SYSTEM\CurrentControlSet\Services\"$(TempTargetService)"\Linkage" Debug-Output "INF: TargetServiceString: "$(TargetServiceString) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(TempTargetService)"\Linkage" $(MAXIMUM_ALLOWED) ServiceLinkageKey GetRegValue $(ServiceLinkageKey), "Bind", TempValue Ifint $(RegLastError) == $(!REG_ERROR_SUCCESS) Set ServiceBindList = *($(TempValue),4) ForListDo $(ServiceBindList) Split-String $($) "\" TestItem Debug-Output "INF: Test Item List: "$(TestItem) ifcontains(i) $(ServiceToBePruned) in $(TestItem) Debug-Output "INF: Disabling binding between: "$(ServiceToBePruned)" and "$(TempTargetService) Shell "", EnableDisableBindings, $(TempTargetService), "\Device\"$(ServiceToBePruned), "disable" endIf EndForListDo Endif CloseRegKey $(ServiceLinkageKey) endif EndForListDo returnDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.