1. tl-6200i.exe Driver
2. README.TXT File Contents

README.TXT Driver File Contents (tl-6200i.exe)

        Driver Installation Guide for Windows For Workgroups 3.11
       ***********************************************************

Introduction

    This document describes the procedures to install NDIS 3.0 driver on
    Windows for Workgroups 3.11.

    This driver conforms to the Network Driver Interface Specification
    (NDIS 3.0) defined by Microsoft.


Installation Procedure


    1. Turn your computer off, then Install your Ethernet Adapter to your
       computer.

    2. After the adapter installation, turn your computer on.

    3. Start your Windows for Workgroups 3.11.

    4. After Windows Start OK, Select "Network" icon and then Select
       "Network  Setup" icon.

    5. Click the "Drivers..." button.

    6. If you are replacing a previous LAN adapter select the Remove button
       to delete that adapter

    7. Click the "Add Adapter" button.

    8. Select "Unlisted or Updated Network Adapter" item bar on the Adapter
       list.

    9. Insert the driver diskette into drive A: or B: and enter A:\WFW311
       or B:\WFW311.

   10. Select the adapter that matches your hardware from the Network
       Adapters list

             [DEC (DC21x4) PCI Ethernet WfW Driver Disk]

       ,then Select "OK" bar.

   11. For PCI adapters, the driver's [Setup..] option allows the user to
       change the following driver's properties:

       * BurstLength:    Specify the length of the DMA data transfer within
                         a PCI burst (1dword = 4 bytes)

             1_dword
             2_dwords
             4_dwords
             8_dwords
            16_dwords  (default)
            32_dwords  (DC21140 only)

       * Bus Number:     Specify the PCI Bus Number the adapter is plugged in.
                         Should be modified only for adapter plugged over a
                         PCI to PCI bridge.

            0  (default)
            1
            2

       * ConnectionType:   Specify the selected Media port

       ------------------------------------------------------------------------
        Digital 10/100Mbps Fast Ethernet Adapter (DECchip 21140)
       -------------------------------------------------------------------------
          o AutoSense                  Senses dynamically the media ports

          o 100BaseTx                  To connect 100BaseTx Ethernet hubs

          o 100BaseTx Full_Duplex      To connect 100BaseTx Full Duplex hubs

          o 100BaseT4                  To connect 100BaseT4 Ethernet hubs

          o 100BaseFx                  To connect 100BaseFx Ethernet hubs

          o 10BaseT                    To connect 10BaseT Ethernet hubs

          o 10BaseT Full_Duplex        To connect 10BaseT Full Duplex hubs


        * PciMechanism:   Specify the mechanism access to the PCI
                          configuration space.

          o AutoDetect                  Detect the system's PCI mechanism
                                        automatically

          o Mechanism 1                 Force PCI mechanism #1 accesses to the
                                        PCI configuration space

          o Mechanism 2                 Force PCI mechanism #2 accesses to the
                                        PCI configuration space

        * ReceiveBuffers:  Specify the size of the receive buffer's ring

           8 .. 64  (default 16)


        * MapRegisters = REG_DWORD {4,8,16}   (default: 8)

                         Number of map registers allocated
                         by the adapter.

        * SnoozeMode = REG_DWORD { 0 | 1 }  (DC21041 only)

                         CFDA<SM>    0 Disabled (default)
                                     1 Enabled


        * StoreAndForward = REG_DWORD { 0 | 1}  (DC21140 only)

                         Select the StoreAndForward mode if a low PCI
                         bandwith causes Transmit Underruns

                         CSR6<SF>    1 StoreAndForward mode


        * TransmitThreshold = REG_DWORD { 72 | 96  | 128 | 160 |
                                          256 | 512 | 1024        }

                         CSR6<TTM,TR>  72 bytes
                                       96 bytes (DC2104X's default)
                                      128 bytes
                                      160 bytes (DC21140's default)
                                      256 bytes (DC21140 only)
                                      512 bytes (DC21140 only)
                                     1024 bytes (DC21140 only)

   12. Select "Close" bar and then Select "OK" bar to complete installation.

   13. Windows prompts you to insert several WFW system diskettes.

   14. When message "Windows Setup has modified your SYSTEM.INI and
       PROTOCOL.INI...    ....." appears, select "OK" bar.

   15. Select "Restart Computer" bar.

   16. Now, the Windows for Workgroup 3.11 is ready for your Ethernet
       Adapter.