Driver installation Guide for Novell NetWare Client 32
*********************************************************
Introduction
============
This readme file describes the procedure to install 32-bit ODI driver
on "Novell NetWare Client 32".
Installation Procedure
======================
A. Install Client 32 for Windows 95 :
NOTE: Please install Novell Netware Client 32 for Windows 95 first.
Method 1: First-time Installation
---------------------------------
If you have previously installed DC21X4.LAN driver of the Netware
Client 32 under your Windows 95 system, skip this section and see
"Follow-up Installation" below.
1. Make sure there is no LAN Card plugged on your machine.
2. Start Windows 95 and get into "Control Panel".
3. Double click "Network" icon, then at the "Configuration" screen
remove all items in list box, after that click "Add" button.
4. On "Select Network Component Type" screen, click "Adapter" which
locates at list box and then click "Add" button
5. On "Select Network Adapters" screen, click "Have Disk" button.
6. On "Install From Disk" screen, input the path where the driver
locates, ex. A:\CLIENT32 or B:\CLIENT32 or
You can click "Browse" button to search for the path where the
driver locates.
7. Another "Select Network Adapters" will be popped up and the
following list is displayed:
[ EB40 10Mbps PCI networking card ]
[ EB41 10Mbps PCI networking card ]
* [ EB140A-TX 10/100Mbps PCI networking card ]
[ EB142/EB143 10/100Mbps PCI networking card ]
Click the card type which you want to installed and click the
"OK" button.
8. Follow screen instructions until installation is finished.
9. Don't restart your Windows 95 system right now.
10. Get into "Control Panel" again.
11. Double click "Network" icon, then at the "Configuration" screen
remove all items in list box and click "OK" button.
12. Power off and plug Adapter into slot.
13. Start Windows 95, then EB140A-TX 10/100Mbps PCI networking card will
be found.
14. In "Copying files ..." screen, input the path where the drivers
locates, ex. A:\CLIENT32 or B:\CLIENT32
15. Follow screen instructions until installation is finished.
16. Reboot your system.
Method 2: Follow-up Installation
--------------------------------
If you are re-installing or updating DC21X4.LAN driver of Novell
Netware Client 32 under Windows 95 system, follow the procedures
given here. If you have not previously installed DC21X4.LAN driver
of Novell Netware Client 32 under your Windows 95 system, see the
"First-time Installation" above.
1. Power off and plug Adapter into slot.
2. Start Windows 95, then EB140A-TX 10/100Mbps PCI networking card will
be found.
3. In "Copying files ..." screen, input the path where the drivers
locates. ex. A:\CLIENT32 or B:\CLIENT32
4. Follow screen instructions until installation is finished.
5. Reboot your system.
B. Client 32 for DOS/Windows 3.1x :
Method 1: Install Driver During Installing Client 32
----------------------------------------------------
1. Follow the installation setps of Novell Netware Client 32 for
DOS/Windows 3.1x.
2. When 'Insert the NETWARE CLIENT 32 FOR DOS/WINDOWS 3.1x DISK 5 -
LAN DRIVER' diskette ...etc. is prompted insert the desired
diskette and on "Insert The Driver Disk" screen input the path
where the driver locates: ex. A:\CLIENT32 or B:\CLIENT32
3. Select the desired parameters and continue the procedure.
4. After installation is finished, the following files will be created:
"\NOVELL\DOSCLNT" is installed path of Client32 for DOS/Windows 3.1x.
Example of STARTNET.BAT (for 32-bit LAN driver) ---
SET NWLANGUAGE=ENGLISH
C:\NOVELL\DOSCLNT\NIOS.EXE
LOAD C:\NOVELL\DOSCLNT\LSLC32.NLM
LOAD C:\NOVELL\DOSCLNT\CMSM.NLM
LOAD C:\NOVELL\DOSCLNT\ETHERTSM.NLM
LOAD C:\NOVELL\DOSCLNT\DC21X4.LAN FRAME=ETHERNET_802.2
LOAD C:\NOVELL\DOSCLNT\DC21X4.LAN FRAME=ETHERNET_802.3
LOAD C:\NOVELL\DOSCLNT\DC21X4.LAN FRAME=ETHERNET_II
LOAD C:\NOVELL\DOSCLNT\DC21X4.LAN FRAME=ETHERNET_SNAP
LOAD C:\NOVELL\DOSCLNT\IPX.NLM <-- Binding driver
LOAD C:\NOVELL\DOSCLNT\CLIENT32.NLM <-- Finding server
Example of NET.CFG ---
Link Driver DC21X4
Frame Ethernet_802.2
Frame Ethernet_802.3
Frame Ethernet_II
Frame Ethernet_SNAP
NetWare DOS Requester
FIRST NETWORK DRIVE = F
NETWARE PROTOCOL = NDS BIND
NOTE: You can run the Netware client installation program for each
workstation type from the CLIENT directory under SYS:PUBLIC or
directly from the CD-ROM.
Method 2: Install Driver after Client 32 is Installed
-----------------------------------------------------
1. Use text editor to edit STARTNET.BAT directly.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.