Page1=LNB && Switch Page2=Dish Setting Page3=Filter Page5=Statistics Page10=Cable Setting Page11=Filter Page20=Terrestrial Setting Page21=Filter Ok=OK Cancel=Cancel Dialog1=Satellite Info/Channel Info Dialog2=Transponder Info Dialog3=PID Info Dialog4=About DVB-Data String1=This transponder already exist. String2=Can not reach this satellite from your location! String3=Cann't input more than four chars. String4=Input Data PID between Hex: 0015-1FFE. String5=Input Data PID between Dec: 21-8190. String6=This PID already exist. String7=Are you sure to remove the current PID? String8=Please successfully lock current transponder at first. String9=The filter don't start,please lock again. String10=Can't unload this PID,please try it again. String11=This value must be less than 45000. String12=Error!PID Data can`t be empty!!! String13=Input Data PID between 21 and 8190 (Hex: 0015-1FFE)! String14=Degree value must be 0--3600. String15=Frequency data is invalid,it must be 950-14000. String16=Symbol rate data is invalid,it must be 900-45000. String17=Polarity is invalid. String18=Can't initialize hardware infomation,this application will exit. String19=This satellite already exists. String20=Are you sure to remove the current satellite? String21=Can't stop filter,so we can't remove current transponder. String22=The current transponder already changed.The locked transponder is not the current transponder,please lock the current transponder at first. String23=Log file's size is bigger than 1M bytes.Do you want to clear it?If not,It cann't save any log message. String24=Locking,Please wait...... String25=The application will exit,save current changed settings and data? String26=The application will restore settings and data,are you sure? String27=Are you sure to remove the current transponder? String28=Scanning,Please wait...... String29=Are you sure to remove all transponders? String30=This channel already exists. String31=Are you sure to remove the current channel? String32=Please successfully lock current channel at first. String33=The current channel already changed.The locked channel is not the current channel,please lock the current channel at first. String34=Fail to load this PID String35=Fail to unload this PID String36=Hide String37=Show String38=About String39=Exit String40=Satellite name can`t be empty! String41=Satellite degree value can`t be empty! 1001=Satellite list/Channel list 1003=Satellite/Channel 1004=New 1005=Edit 1006=Remove 1008=Help 1009=Apply 1011=Language 1013=Strength 1014=Quality 1017=Dish Type 1018=Fixed 1019=DiSEqC 1.2 (motor) 1020=USALS (motor) 1021=LNB Power 1022=22KHz Tone 1030=Vertical 1031=Horizontal 1036=Add 1037=Remove 1038=Set East Limit 1039=Set West Limit 1040=Cancel Limit 1041=Goto Zero 1042=Goto Satellite 1043=Decimal 1044=Hexadecimal 1045=Set Multicast PIDs automatically 1046=Use the MAC address of the hardware 1047=Caculate MAC address from IP address of Dial-up connection 1048=Caculate MAC address from IP address of network interface card 1049=Caculate MAC address from the following IP address 1054=DVB-Data Version 1.6 1055=Copyright (C) 2004 1056=OK 1057=Satellite 1058=Dish options 1059=Dish Type 1060=Satellite 1061=Degree 1065=Transponder options 1066=Transponder 1067=Frequency 1068=Symbol Rate 1072=Polarization 1073=Motor Settings 1074=Longitude 1075=Latitude 1076=Degrees 1077=Elevation 1079=Drive East 1080=Drive West 1081=Lock Test 1082=Scan.... 1083=Unicast(internet) Filter setting 1084=IP to MAC prefix 1087=Default PIDs 1088=Unicast PID 1089=Broadcast PID 1090=Multicast PID 1094=Proxy IP address 1095=Proxy IP address 1096=Port 1098=Load 1099=Unload 1100=LNB Setting 1101=LNB 1102=LNB Freq.1 1103=LNB Freq.2 1105=DiSEqC 1106=Total Data Rate 1111=Name 1112=Degree 1113=New 1115=Symbol Rate 1116=Frequency 1118=Vertical 1119=Horizontal 1129=Hexadecimal(0015-1FFE) 1130=Decimalization(21-8190) 1131=PID Data: 1132=Remove 1134=Frequency: 1137=KHz(40000 ~ 870000 KHz) 1141=Symbol Rate: 1143=Ksps(0 ~ 7000 Ksps) 1144=QAMSize: 1150=Channel Info 1151=Lock Test 1157=Switch Setting 1159=PID Type: 1162=MHz 1163=Ksps 1164=MHz 1165=Ksps 1166=Restore 1167=Motor Position 1168=Position: 1170=Goto 1171=Set 1173=Data statistic 1176=Bytes 1177=Receive 1178=Error 1179=Total 1180=Packets 1181=Receive 1182=Error 1183=Total 1184=Speed 1193=Mbytes 1194=Mbytes 1195=Mbytes 1196=KPackets 1197=KPackets 1198=KPackets 1199=Kbps 1200=Lock Test 1201=Full Scan 1202=Frequency 1204=BandWidth 1206=Step 1208=Channel Info 1209=KHz(51000 ~ 860000 KHz) 1210=MHz 1211=MHz(1 ~ 8 MHz) 1212=Mac AddressDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.