Driver Diskette (Ver 6.00) Overview For 10/100 Mbps Fast Ethernet CardBus PC Card TOPIC ====================================== 1. DISKETTE CONTENTS 2. NETWORK DRIVERS FOR WINDOWS 95 3. NETWORK DRIVERS FOR WINDOWS 98 4. NETWORK DRIVERS FOR WINDOWS NT4.0 5. NETWARE DOS ODI DRIVER [1] DISKETTE CONTENTS Files and Subdirectories Contents -------------------------------------------------------------------- \README.TXT This file \LDTS100N.INF An INF file for Windows 95 and Windows 98 \OEMSETNT.INF An INF file for WinNT4.0 \LNDX100.SYS Windows 95,98,NT4.0 Driver \ODI Novell Netware DOS ODI Driver \ENABLER Contains enabler programs to enable CardBus \MANUAL\man100n.htm Manual file, HTML format [2] Network Drivers for Windows 95 OSR2 INSTALLATION PROCEDURE: 1) Plug the 10/100 Ethernet CardBus Adapter into the CardBus slot, and insert "Driver Diskette" into Drive A:. The system displays the "Update Device Driver Wizard" dialog box, press "Next" button. 2) If no driver is found, select "Other Locations". Then input "A:\" to specify the driver's location where the device information file (.INF file) and the driver (.SYS file) can be found. 3) Press "OK", the driver then installs itself. If have "Insert Disk" dialog box for asking other file, type in your Windows path or Windows\system or your Winsows 95 CD-ROM to find the file. 4) Click "Finish" to complete the installation process. 5) Reboot the machine to start the network. [3] Network Drivers for Windows 98 INSTALLATION PROCEDURE: 1) Plug the 10/100 Ethernet CardBus Adapter into the CardBus slot, and insert "Driver Diskette" into Drive A:. The system displays the "Add New Hardware Wizard" dialog box, press "Next" button. 2) Select "Search for the best driver for your device", click "Next". 3) Select "Floppy disk drives", press "Next" button. 4) If the driver is found, press "Next" button, then it installs itself. 3) If have "Insert Disk" dialog box for asking other file, type in your Windows path or Windows\system or your Winsows 98 CD-ROM. 4) Click "Finish" to complete the installation process. 5) Reboot the machine to start the network. [4] NDIS 4.0 DRIVER FOR WINDOWS NT4.0 The NT4.0 driver supports 15 types of CardBus Controllers, include TI1130, TI1131, TI1250, TI1220, TI1221, TI1225, TI1251, Cirrus Logic 6832, O2 Micro OZ6832/6833, 6836/6860, 6812, Toshiba ToPIC95,Ricoh RL5C475, 476, and 478. INSTALLATION PROCEDURE: 1) Open the Control Panel, and choose Network Settings. 2) Select the "Adapter". 3) Click "Add" button. 4) Press "Have Disk" button. 5) You can see "10/100 Mbps FastEthernet CardBus PC Card" in the dialog box, Press "OK". 6) Select the CardBus Controller's IRQ and I/O address. 7) Then go back "Network", select "Bindings" 8) Press "Close" button. 9) Asking your Server Administrator how to assign the IP address. 10) Click on "OK" and restart the computer. 11) Please go to "Devices" of "Control Panel" for check the driver status, if it display "10/100 Mbps FastEthernet Started Automatic", the driver is wroking. 12) If still can't link to network, user can try another IRQ number, maybe 5, 9, 10, or 11. [5] Netware DOS ODI Driver 1. For those who installed EMM386.EXE in your config.sys, please exclude memory address D400-D7FF from your system. PCMCIA Ethernet card enabler program will use this space to read Ethernet ID and CIS from on-board flash memory. [Example] DEVICE=EMM386.EXE NOEMS X=D400-D7FF or DEVICE=EMM386.EXE NOEMS X=D000-DFFF 2. User need to add "LASTDRIVE=[Device Name]" in the Config.sys file, then reboot Notebook. Example, if you want to login to Device "N", the string is "LASTDRIVE=M". 3. Enable the FastEthernet PC Card The "\ODI" directory contains Ethernet DOS ODI driver DC21X4.COM that supports NetWare 3.x and 4.x, NetWare Lite and other ODI interface application. DC21X4.COM : DOS/ODI Driver for NetWare 3.x and 4.0. You can follow the instruction below to install DOS ODI Drivers of Novell's NetWare Operating System. How To Install -------------- You need following some files to install DOS ODI DRIVER. a. PBX.COM ---- Intercept PCI BIOS function call b. ENABLER.EXE ---- Enabler Program for CardBus Controllers c. LSL.COM ---- supported by Novell d. DC21X4.COM ---- Novell DOS ODI Driver ,supported by manufacturer e. IPXODI.COM ---- supported by Novell f. NETx.EXE ---- supported by Novell or EMSNETx.EXE or XMSNETx.EXE g. NET.CFG ---- optional,configuration file There is a sample BATCH file named "STARTNET.BAT". You can type "STARTNET" command to log in to the Netware's File Server. If want to know more information, Please read the "readme.txt" file in the \ODI directory. Normally, you will need a NET.CFG file to configure your Ethernet PC Card. You can see Netware 386 Installation appendix E for more information about NET.CFG. Below is a sample NET.CFG file: LINK DRIVER CARDODI Frame Ethernet_II Frame Ethernet_802.3 Protocol IPX 0 Ethernet_802.3 : : Error messages ============== - FATAL: Failed to lock system memory Driver call to OS memory support routines for locking its internal buffers and descriptors failed. - FATAL: DC21X4 driver works only with 386 or above! The driver failed to identify the CPU as a 386 or above the driver can run on 386 (or above) machines only. - FATAL: Slot value error! The user has specified an illegal slot number in NET.CFG 50 - FATAL: Board not found in system Driver could not detect a supported NIC in the system. 200 - FATAL: Timeout when initializing DC21X4 with setup packet! This happens mainly when the PCI slot does not support DMA. Make sure the BIOS setup or motherboard switches are set to enable DMA or Bus Master operation of this slot. 210 - FATAL: DC21X4 Does not support this bus type The machine is not identified as a PCI machine or the user has specified BUS ID which is not PCI. 212 - FATAL: DC21X4 Does not support this device revision The DC21x4 drivers do not support DC21140 rev 1.0 chip. If you receive this message, please make sure you have an updated rev of your NIC. 217 - FATAL: Failed to find PCI BIOS The machine is not identified as a PCI machine (to support PCI NICs). This error is generated when the driver is directed to load a PCI NIC using the BUS ID keyword (in DC21X4.COM v2.0 and above) and PCI 4 is specified, or SLOT keyword (in DC21X4 V1.02 and below), and slot value is a PCI slot number (16 and above). 218 - FATAL: Bad PCI BIOS status PCI BIOS returned a fail status in one of the calls. Please check the BIOS version and BIOS correctness using an external utility. 219 - FATAL: Bad PCI BIOS Register err PCI BIOS returned a fail status in one of the calls. Please check the BIOS version and BIOS correctness using an external utility. 220 - FATAL: PCI BIOS failed to initialize DECchip 21x40 CBIO reg! PCI BIOS has initialized a DWORD register in the NIC's configuration space (at offset 10Hex) with illegal value (in x86 machines this value is between 0 to FFFFHex). Please check the BIOS using an external utility. Also verify that your BIOS setup enables the slot the NIC is plugged in, allocates I/O addresses to it and initializes correctly the device in this PCI slot. 222 - WARNING: KWD RXD No param The user added the RX_BUFFERS key word in NET.CFG but did not specify the number of buffers required. Add the number of buffers to the KWD (such as: RX_BUFFERS 9) 222 - WARNING: KWD RXD Param too small The number of Rx buffers specified by the user is too small for proper driver's work. Please increase the amount of Rx buffers in RX_BUFFERS KWD in NET.CFG The minimum number of rx buffers is 2. 222 - WARNING: KWD RXD Param too big The user had specified more rx buffers than the driver can handle Please decrease the amount of Rx buffers in RX_BUFFERS KWD in NET.CFG The maximum number of rx buffers is 16 but it may be less depending on the driver's size. 225 - FATAL: PCI BIOS allocated an illegal Interrupt to DECchip 21x40! PCI BIOS has initialized a byte register in the NIC's configuration space (at offset 3CHex) with illegal value (in x86 machines legal values are between 1 to 15). Please check the BIOS using an external utility. Also verify that your BIOS setup enables the slot the NIC is located in, enables interrupts to this slot and assigns a legal interrupt number to it. 226 - WARNING: Can not handle Turbo switch Cannot operate the 'Turbo' mechanism from one of the following reasons: - The chipset on the motherboard does not support TURBO mode. - The chipset parameters are unknown to the driver. 226 - FATAL: Failed to handle Turbo switch Failed to operate the 'Turbo' mechanism from one of the following reason: - PCI BIOS returned a fail status in one of the calls involved with operating this mechanism. We strongly recommend to reboot the PC after such an Error occures 227 - FATAL: Internal CRC table corrupted Driver found an error in internal CRC table either because the driver file is corrupted or someone has changed the table's contents. 228 - FATAL: Could not handle chipset bug workaround successfully Failed to operate chipset bug workaround because PCI BIOS returned a fail status in one of the calls involved with operating this mechanism. 229 - WARNING: This machine Host to PCI bridge has a known bug. Driver limits DC21X4 bursts as a workaround. 230 - FATAL: This machine Host to PCI bridge has a known bug when using cache in WB mode which may cause data corruption or system hang. Please change the cache mode to WT (Write Through) as a workaround. 231 - WARNING: The PCI Host Bridge present in this machine requires that the driver switch to Store and Forward Mode. Network performance may be affected. The driver detected a PCI Host Bridge with limited data transfer rates to be present in the PC. it modifies DC21X4 chip parameters for working in such a system. This may slightly slow the network performance. No further action is needed. 240 - FATAL: Unable to locate Adapter ROM! Driver failed either to locate the address ROM or read it. This might happen due to bad data stored in the serial ROM. 240 - FATAL: Failed to read ROM! Driver failed to read the serial flash ROM due to a hardware failure. Make sure the IEEE flash ROM on your NIC is operational using external utility. 240 - FATAL: Unsupported ROM Version The version (and hence the format) of the data read from the SROM is not supported by the driver. Please run an external utility to upgrade the Serial ROM's data. 240 - FATAL: This DS chip does not support this ROM version This ROM version does not contain the information needed by the driver in order to correctly activate the DS chip located on-board. Please run an external utility to upgrade the Serial ROM's data and add the device specific information to it. 241 - FATAL: Unsupported media selection The NIC or device do not support the requested media selection. Please check the available media types on the NIC and use one of them. 241 - FATAL: Could not find media or PHY to work with The driver failed to find any medium in the NIC. This may happen due to a bad Serial ROM programming or an MII PHY failure. 242 - WARNING: Could not find a connected medium. The Power-Up autosense could not find a connected medium, Please connect a cable to one of the ports and the Autosense routine will automaticlly find and use it.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.