;localization: ;Copy eng.ini to xxx.ini(xxx is taking the 2-letter language ;abbreviation from the ISO Standard 639 and adding a third letter, ;as appropriate, to indicate the sublanguage). ; ;This session must use english ; ;Mike Fu 03/05 ; [Info] Language=English Version=0.1a [GLOBAL] Title=Wireless AP 22M Utility Refresh=Refresh Apply=Apply Close=Close Default=Default QuitAsk=Do you want quit setup utility? QuitASKTitle=Information DefaultAsk=Do you want restore Access Point default value? DefaultAskTitle=Information link=Link Info. apset=AP Settings ipset=IP Settings wepset=WEP Settings ap_list=Available AP statue=Status apname=AP Name macaddr=Mac Address ssid=SSID wep=Wep [Status] Title =Status AP =AP Name : Essid =ESSID : IP =IP Address : Mac =Mac Address : WEP =WEP Security : FW =Firmware Version: REGDOMAIN=Domain : CH =Channel : [AP] Title=AP Settings Basic=Basic Settings Essid=ESSID CH=Channel APName=AP Name RemoteAPMAC=Remote AP MAC Address RemoteBridgeMAC=Remote Bridge MAC Address APMode=AP Mode¡G APMode1=Access Point APMode2=Access Point Client APMode3=Wireless Bridge APMode4=Multiple Bridge Mode=Mode Setting SSID_BCast=SSID Broadcast BCast_ON=Enable BCast_OFF=Disable RATES=Transmission Rates Rate1=1-2 (Mbps) Rate2=1-2-5.5-11 (Mbps) Rate3=1-2-5.5-11-22(Mbps) Preamble=Preamble Type Preamble1=Short Preamble Preamble2=Long Preamble Auth_Type=Auth. Mode Auth_Type1=Open Authentication Auth_Type2=Shared Authentication Auth_Type3=Auto Switch Advance Setting=Advance Setting ;more page MoreSet=Advance Setting MoreSet1=Advance Setting Beacon=Beacon Interval RTS=RTS Threshold Fragmentation=Fragmentation Threshold DTIM=DTIM Interval Antenna=Antenna Selection Antenna1=Left Antenna Antenna2=Right Antenna Antenna3=Diversity Antenna MoreOK=OK MoreCancel=Cancel [IP] Title=IP Settings DHCP=DHCP Client FixIP=Fix IP Address IPSetting=IP Address Setting IP=IP Address SubMask=Subnet Mask Gateway=Gateway [WEP] Title=WEP Setting WEP=Key Length encry= Data Encryption ;Wep_ON=Enable ;Wep_OFF=Disable ;Wep_Set=Disable Wep_Set64=64 bits Wep_Set128=128 bits Wep_Set256=256 bits PASS=Passphrase PASS_B=Done WEPSET=WEP Key Setting HEX=Hex ASCII=ASCII Key1=Key 1 Key2=Key 2 Key3=Key 3 Key4=Key 4 SelKey=Use WEP Key K1=1 K2=2 K3=3 K4=4 [System] Title=System LOADSAVE=Backup/Restore Setting OpenFileErr=Open File error.. SelINI=Bowser... INIFormat=INI files (*.ini)|*.ini|All files (*.*)|*.* Backup_B=Backup Restore_B=Restore NoINI_File=No set file name! OverWrite=Do you want over write this file? OverWrite_Title=Warring LoadAsk=Do you want load this file setting in to the AP? LoadAskTitle=Warring UPDateFW=UpDate Firmware SelFW=Bowser... FWFormat=BIN files (*.bin)|*.bin|All files (*.*)|*.* UPDateFW_B=Update MacFilterSet=Mac Filter Setting MacFilter=Mac Filter MacFilterOn=Enable MacFilterOff=Disable FilterSet=Setting APPW_B=AP Password Password=System - AP Password Setting Password1=Admin Password PW1=New Password PW2=Retype Password PW_OK=OK PW_CANCEL=Cancel PW_Err=Password not match! [ErrMsgCap] Err_e_beacon=Beacon Interval Range Error Err_e_rts=RTS Threshold Range Error Err_e_frag_rang=Fragmentation Threshold Range Error Err_e_frag_even=Fragmentation Threshold Setting Error Err_e_dtim=DTIM Interval Range Error Err_IP=IP Settings Error PW_Err=Confirm Error Stru_Logic=Structure Error Err_wep_key=Wep Key Error Err_Re_Mac=Remote Mac Address Error Err_IP_1=IP Setting Error Err_IP_2=Submask Setting Error Err_IP_3=Gateway Setting Error [ErrRangMsg] Err_e_beacon=The reasonable range is 1 ~ 1000 ! Err_e_rts=The reasonable range is 256 ~ 2432 ! Err_e_frag_rang=The reasonable range is 256 ~ 2346 ! Err_e_frag_even=The data must be even number ! Err_e_dtim=The reasonable range is 1 ~ 65535 ! Err_IP=The reasonable range is 0 ~ 255 ! PW_Err=Password does not match! Stru_Logic=The Package data is not match the logic! Err_wep_keyStr1=The wep key Err_wep_keyStr2=value is not correct! Err_Re_Mac=Remote Mac Address value is not correct! Err_IP_1=IP Setting value is not correct! Err_IP_2=Submask Setting value is not correct! Err_IP_3=Gateway Setting value is not correct! [ApplyMsg] mescap=Message updatemsg=The Utility is update setting now ... updatefail=Apply is fail. Please check the setting value. noselect=Please select an apply AP. [About] Title=About ViewLog=View LogDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.