1. acpW22all.zip Driver
2. eng.ini File Contents

eng.ini Driver File Contents (acpW22all.zip)

;localization:
;Copy eng.ini to xxx.ini(xxx is taking the 2-letter language
;abbreviation from the ISO Standard 639 and adding a third letter,
;as appropriate, to indicate the sublanguage).
;
;This session must use english
;
;Mike Fu  03/05
;
[Info]
Language=English
Version=0.1a

[GLOBAL]
Title=Wireless AP 22M Utility
Refresh=Refresh
Apply=Apply
Close=Close
Default=Default
QuitAsk=Do you want quit setup utility?
QuitASKTitle=Information
DefaultAsk=Do you want restore Access Point default value?
DefaultAskTitle=Information
link=Link Info.
apset=AP Settings
ipset=IP Settings
wepset=WEP Settings
ap_list=Available AP
statue=Status
apname=AP Name
macaddr=Mac Address
ssid=SSID
wep=Wep


[Status]
Title            =Status
AP              =AP Name       :
Essid          =ESSID           :
IP                =IP Address     :
Mac            =Mac Address  :
WEP            =WEP Security  :
FW             =Firmware Version:

REGDOMAIN=Domain          :
CH                   =Channel         :

[AP]
Title=AP Settings
Basic=Basic Settings
Essid=ESSID
CH=Channel
APName=AP Name
RemoteAPMAC=Remote AP MAC Address
RemoteBridgeMAC=Remote Bridge MAC Address
APMode=AP Mode¡G
APMode1=Access Point
APMode2=Access Point Client
APMode3=Wireless Bridge
APMode4=Multiple Bridge

Mode=Mode Setting
SSID_BCast=SSID Broadcast
BCast_ON=Enable
BCast_OFF=Disable
RATES=Transmission Rates
Rate1=1-2 (Mbps)
Rate2=1-2-5.5-11 (Mbps)
Rate3=1-2-5.5-11-22(Mbps)
Preamble=Preamble Type
Preamble1=Short Preamble
Preamble2=Long Preamble
Auth_Type=Auth. Mode
Auth_Type1=Open Authentication
Auth_Type2=Shared Authentication
Auth_Type3=Auto Switch
Advance Setting=Advance Setting

;more page
MoreSet=Advance Setting
MoreSet1=Advance Setting
Beacon=Beacon Interval
RTS=RTS Threshold
Fragmentation=Fragmentation Threshold
DTIM=DTIM Interval
Antenna=Antenna Selection
Antenna1=Left Antenna
Antenna2=Right Antenna
Antenna3=Diversity Antenna
MoreOK=OK
MoreCancel=Cancel

[IP]
Title=IP Settings
DHCP=DHCP Client
FixIP=Fix IP Address
IPSetting=IP Address Setting
IP=IP Address
SubMask=Subnet Mask
Gateway=Gateway

[WEP]
Title=WEP Setting
WEP=Key Length
encry=    Data Encryption

;Wep_ON=Enable
;Wep_OFF=Disable
;Wep_Set=Disable

Wep_Set64=64 bits
Wep_Set128=128 bits
Wep_Set256=256 bits

PASS=Passphrase
PASS_B=Done
WEPSET=WEP Key Setting
HEX=Hex
ASCII=ASCII
Key1=Key 1
Key2=Key 2
Key3=Key 3
Key4=Key 4
SelKey=Use WEP Key
K1=1
K2=2
K3=3
K4=4

[System]
Title=System
LOADSAVE=Backup/Restore Setting
OpenFileErr=Open File error..
SelINI=Bowser...
INIFormat=INI files (*.ini)|*.ini|All files (*.*)|*.*
Backup_B=Backup
Restore_B=Restore
NoINI_File=No set file name!
OverWrite=Do you want over write this file?
OverWrite_Title=Warring
LoadAsk=Do you want load this file setting in to the AP?
LoadAskTitle=Warring
UPDateFW=UpDate Firmware
SelFW=Bowser...
FWFormat=BIN files (*.bin)|*.bin|All files (*.*)|*.*
UPDateFW_B=Update
MacFilterSet=Mac Filter Setting
MacFilter=Mac Filter
MacFilterOn=Enable
MacFilterOff=Disable
FilterSet=Setting
APPW_B=AP Password
Password=System - AP Password Setting
Password1=Admin Password
PW1=New Password
PW2=Retype Password
PW_OK=OK
PW_CANCEL=Cancel
PW_Err=Password not match!

[ErrMsgCap]
Err_e_beacon=Beacon Interval Range Error
Err_e_rts=RTS Threshold Range Error
Err_e_frag_rang=Fragmentation Threshold Range Error
Err_e_frag_even=Fragmentation Threshold Setting Error
Err_e_dtim=DTIM Interval Range Error
Err_IP=IP Settings Error
PW_Err=Confirm Error
Stru_Logic=Structure Error
Err_wep_key=Wep Key Error
Err_Re_Mac=Remote Mac Address Error
Err_IP_1=IP Setting Error
Err_IP_2=Submask Setting Error
Err_IP_3=Gateway Setting Error

[ErrRangMsg]
Err_e_beacon=The reasonable range is 1 ~ 1000 !
Err_e_rts=The reasonable range is 256 ~ 2432 !
Err_e_frag_rang=The reasonable range is 256 ~ 2346 !
Err_e_frag_even=The data must be even number !
Err_e_dtim=The reasonable range is 1 ~ 65535 !
Err_IP=The reasonable range is 0 ~ 255 !
PW_Err=Password does not match!
Stru_Logic=The Package data is not match the logic!
Err_wep_keyStr1=The wep key
Err_wep_keyStr2=value is not correct!
Err_Re_Mac=Remote Mac Address value is not correct!
Err_IP_1=IP Setting value is not correct!
Err_IP_2=Submask Setting value is not correct!
Err_IP_3=Gateway Setting value is not correct!

[ApplyMsg]
mescap=Message
updatemsg=The Utility is update setting now ...
updatefail=Apply is fail. Please check the setting value.
noselect=Please select an apply AP.

[About]
Title=About
ViewLog=View Log