1. l100.exe Driver
2. WKPLACE.TXT File Contents

WKPLACE.TXT Driver File Contents (l100.exe)

    Driver Installation - Novell LAN WorkPlace for DOS
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

  Siemens OfficeLAN PCI 10/100 TX Fast Ethernet Adapter

  Novell LAN WorkPlace v4.0 for DOS Driver
  INSTALLATION GUIDE


=============================================================================
CONTENTS
=============================================================================

*  Important Considerations

*  System Requirements

*  Files Provided

*  Hardware Installation Guide

*  Device Driver Installation Guide

*  Modifying Line Speed

=============================================================================
IMPORTANT CONSIDERATIONS
=============================================================================

*  For custom installations (multiple frame types), refer to your Novell
    NetWare ODI Shell for DOS manual.

=============================================================================
SYSTEM REQUIREMENTS
=============================================================================

Hardware Requirements:

*  IBM-compatible personal computer (PC), 80486 or higher with PCI bus
    supporting bus master mode

Firmware Requirements:

*  Fully compliant Rev. 2.0 or higher PCI BIOS supplied with the PC

Software Requirements:

*  MS-DOS v3.0 or higher

*  Novell IPXODI (provided on the ConfigDisk)

*  Novell LSL (v2.11 or higher, provided on the ConfigDisk)

*  Novell NETX or Novell VLM (provided on the ConfigDisk)

=============================================================================
FILES PROVIDED
=============================================================================

The Novell NetWare DOS ODI client directory includes:

*  L100.COM              Novell NetWare ODI Client driver
*  NET.CFG               Novell network configuration file for the driver

=============================================================================
HARDWARE INSTALLATION GUIDE
=============================================================================

*  See the User Guide for complete installation instructions.

*  When installing the Adapter in a PCI computer, make sure
   the slot you select supports bus master operations.

*  No specialized setup is necessary for motherboards with automatic
    PCI parameterization (most new PCs support it).

*  For motherboards with bus master jumpers and interrupt jumpers for
   PCI slots:

   1.  Using the appropriate motherboard jumper, enable bus master operations
        for the selected PCI slot.

   2.  Using the appropriate motherboard jumper, select the interrupt to the
        selected PCI slot.

   3.  Using your computer setup menu:

        *  Enable the bus master on the PCI slot.

        *  Enable I/O on the PCI slot.

        *  Define the interrupt number on the PCI slot.

=============================================================================
DEVICE DRIVER INSTALLATION GUIDE
=============================================================================

1   Copy the DOS ODI driver related files into the proper directory.

2.  Insert the LAN WorkPlace v4.0 for DOS Install diskette into the
     floppy drive.

3.  Move to the drive where you inserted the diskette.

4.  Type:

     INSTALL [Enter]

5.  Select a target drive and press [Enter].

6.  When the program asks if you want to install the Windows application
     portion of LAN WorkPlace, select either "Yes" or "No" (the choice is not
     applicable to your adapter installation).

7.  Ask your System Administrator to give you the appropriate IP information,
     such as IP address, router address, and subnet mask.

8.  Press [Enter] to continue the installation.

9.  Follow the prompts until asked if you want to update your system
     files. Use the information from Step 7, or see "Installing and
     Configuring the Software" in your Novell LAN WorkPlace for DOS
     User Guide.

10. When prompted to update your system files, select  YES. The program
      automatically creates a backup of your DOS system files if they
      already exist.

11. Follow the prompts to copy the remaining LAN WorkPlace for DOS files
      until you finish the installation.

12. Exit to DOS.

13. Edit the NET.CFG file so that the line speed, cable type, network
     protocol type settings are correct for your network. You do not
     need to specify a PCI slot number or Interrupt number.

    If you do specify the slot number:
     *  PCI slots are counted from 0--that is, the first PCI adapter
         installed is considered to be in slot 0, the next in slot 2,
         and so on.

The example that follows shows what the NET.CFG file should look like.

Lines preceded with > indicate text you must add to the NET.CFG file.

Lines preceded with # (the remark or REM character) are not executed.
Removing the # character activates these lines when you reboot.

*  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *

NOTE:  The following lines must be left-justified in your NET.CFG file
        (do not precede them with the > character; this character only
         marks what you must type in the NET.CFG file):

             Link Support
             Link Driver
             L100
             Protocol TCPIP

            All other lines must be indented.

*  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *

In the example, no values appear next to the parameters in the Protocol TCPIP
section; however, you will see values next to the parameters in the Protocol
TCPIP section of your NET.CFG file. Do not change these values.

     #
     # NET.CFG File for L100
     #
     > Link Support
     >     Buffers 8 1586
     >     MemPool 4096
     Link Driver L100
          Frame Ethernet_802.3
     >    Frame Ethernet_II
     #    Port #1 280
     #    Mem #1 000D0000 2000/10
     #    Int #1 3
     #    PS/2 Slot?
     #
     Protocol TCPIP
     >    Bind         L100
          ip_address
          ip_router
          ip_netmask
          tcp_sockets
          udp_sockets
          raw_sockets
          nb_sessions
          nb_commands
          nb_adapter
          nb_domain

14. Save the NET.CFG file.

15. Reboot your computer.

=============================================================================

This software and documentation have restricted rights: their use,
 duplication, or disclosure by the Government is subject to the
 restrictions in:

*  DFARS 252.227-7013
    Subparagraph (c) (1) (ii)
    Rights in Technical Data and Computer Software clause

*  FAR 52.227-14
    Alternate III
    Rights in Data -- General clause

*  FAR 52.227-19
    Subparagraphs (c) (1) and (2)
    Commercial Computer Software -- Restricted Rights clause


Other product and company names are registered trademarks or trademarks of
their respective holders.