* Windows 98SE Installation Guide
***************************************************
Installing Drivers During Windows 98SE Installation
***************************************************
The following details the installation of the USB 2.0 driver while installing Windows 98SE
(with the USB 2.0 controller is enabled already).
1. After enabling the USB 2.0 controller, install Windows 98/98SE normally.
2. After installation, go the "Start" menu and choose "Settings."
3. From the "Settings" menu, choose "Control Panel."
4. In the "Control Panel" window, double-click on the "System" icon.
5. In the "System" window, choose the "Device Manager" tab.
6. In the hierarchical display under "Other Devices" is a listing for "PCI Universal Serial
Bus." Choose it and then press the "Properties" button.
7. Choose the "Driver" tab in the "Properties" window, choose "Update Driver," and then
press "Next."
8. Choose "Search for a better driver than the one your device is using now (recommended),"
then press "Next."
9. Insert the "Bonus CD" in CD-ROM.
10. Choose "Specify a Location," and then type "[CD-ROM]:\Driver\USB2.0" in the text box.
11. Press the "Next" button. A message informing you that Windows has found "AOpen USB
Enhanced Host Controller" should appear.
12. Press "Next," then "Finish," then "Yes" when asked if you want to restart your
computer.
*********************************************
Installing Drivers with Existing Windows 98SE
*********************************************
The following section details the installation of USB 2.0 driver on a system that has
Windows 98SE already installed.
1. Enable the USB 2.0 controller and boot Windows.
2. The "Add New Hardware Wizard" will appear, informing you that it has found a "PCI
Universal Serial Bus."
3. Click on "Next," and from the generated list box, choose "Search for best driver for your
device (Recommended)".
4. Insert the "Bonus CD" in CD-ROM.
5. Click on "Next," and from the generated choices, choose "Specify a location."
6. Type "[CD-ROM]:\Driver\USB2.0" in the text box that appears.
7. Click on "Next." A message informing you that Windows has found "AOpen USB Enhanced Host
Controller" should appear.
8. Click on "Next," and then on "Finish."
9. Choose "Yes" when asked if you want to restart your computer.
**********************************************
Confirming Driver Installation in Windows 98SE
**********************************************
To confirm that the driver has been properly loaded in Windows 98SE, perform the
following steps:
1. Choose "Settings" from the "Start" menu.
2. Choose "Control Panel," and then double-click on the "System" icon.
3. Choose the "Device Manager" tab, and then click the "+" in front of "Universal Serial
Bus Controllers." "AOpen USB Enhanced Host Controller" should appear.
* Windows Me Installation Guide
*************************************************
Installing Drivers During Windows Me Installation
*************************************************
The following details the installation of the USB 2.0 driver while installing Windows Me
(with the USB 2.0 controller is enabled already).
1. Install Windows Me fully.
2. After installation, go the "Start" menu and choose "Settings."
3. From the "Settings" menu, choose "Control Panel."
4. In the "Control Panel" window, double-click on the "System" icon.
5. In the "System" window, choose the "Device Manager" tab.
6. In the hierarchical display under "Other Devices" is a listing for "PCI Universal
Serial Bus." Choose it and then press the "Properties" button.
7. Choose the "Driver" tab in the "Properties" window, choose "Update Driver," and then
press "Next."
8. Choose "Specify the location of the driver (Advanced)," then press "Next".
9. Insert the Bonus CD in CD-ROM.
10. Choose "Specify a Location," and then type "[CD-ROM]:\Driver\USB2.0" in the text box.
11. Press the "Next" button. A message informing you that Windows Me has found "AOpen USB
Enhanced Host Controller" should appear.
12. Press "Next," then "Finish," then "Yes" when asked if you want to restart your computer.
**************************************************
Installing Drivers with Existing Windows Me System
**************************************************
The following section details the installation of USB 2.0 driver on a system that has
Windows Me already installed and running.
1. After installing the USB 2.0 controller, boot system.
2. The "Add New Hardware Wizard" will appear, informing you that it has found a "PCI
Universal Serial Bus."
3. Click on "Next," and from the generated list box, choose "Specify the location of the
driver (Advanced)."
4. Click on "Next," and from the generated choices, choose "Specify a location."
5. Insert the Bonus CD in CD-ROM.
6. Type "[CD-ROM]:\Driver\USB2.0" in the text box that appears.
7. Click on "Next." A message informing you that Windows Me has found "AOpen USB Enhanced
Host Controller" should appear.
8. Click on "Next," and then on "Finish."
9. Choose "Yes" when asked if you want to restart your computer.
********************************************
Confirming Driver Installation in Windows Me
********************************************
To confirm that the driver has been properly loaded in Windows Me, perform the following
steps:
1. Choose "Settings" from the "Start" menu.
2. Choose "Control Panel," and then double-click on the "System" icon.
3. Choose the "Device Manager" tab, and then click the "+" in front of "Universal Serial
Bus Controllers." "AOpen USB Enhanced Host Controller" should appear.
* Windows 2000 Installation Guide
*************************************************
Installing Driver in Existing Windows 2000 System
*************************************************
After enabling the USB 2.0 controller and rebooting your system, Windows 2000 setup will
show a "New Hardware Found" dialog box. Under Windows 2000, "Universal Serial Bus (USB)
Controller" will be displayed.
1. Choose "Search for a suitable driver for my device (Recommended)". from the list, and
then press "Enter".
2. Choose "Specify a location." and then press "Next"
3. Insert the Bonus CD in CD-ROM.
4. Type "[CD-ROM]:\Driver\USB2.0" in the text box that appears. Press " OK ".
5. Click on "Next." A message informing you that Windows has found "AOpen USB Enhanced
Host Controller" should appear.
6. Click on "Next," and then on "Finish."
************************************
Confirming Windows 2000 Installation
************************************
1. From Windows 2000, open the Control Panel from "My Computer" followed by the System icon.
2. Choose the "Hardware" tab, and then click the "Device Manager" tab.
3. Click the "+" in front of "Universal Serial Bus controllers". "AOpen USB Enhanced Host
Controller" should appear.
* Windows XP Installation Guide
***********************************************
Installing Driver in Existing Windows XP System
***********************************************
After enabling the USB 2.0, Windows XP setup will show a "Found New Hardware" dialog box.
Under Windows XP, "Universal Serial Bus (USB) Controller" will be displayed.
1. Click on "Next," and from the generated list box, choose "Install from a list or special
location (Advanced)", click "Next"
2. Click on "Next," and from the generated choices, choose "Include this location in the
search:"
3. Insert the Bonus CD in CD-ROM.
4. Type "[CD-ROM]:\Driver\USB2.0" in the text box that appears.
5. Click on "Next." A message informing you that Windows XP has found "AOpen USB Enhanced
Host Controller" should appear.
6. When the New Hardware Wizard has finished installing the USB driver, click on "Finish"
**********************************
Confirming Windows XP Installation
**********************************
1. From Windows XP, open the Control Panel from "My Computer".
2. Click on "Performance and maintenance".
3. Click on the "System" icon.
4. Choose the "Hardware" tab, and then click the "Device Manager" tab.
5. Click the "+" in front of "Universal Serial Bus Controllers". "AOpen USB Enhanced Host
Controller" should appear.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.