SmartLink Modio Version 1.52 - APRIL 22, 1998
=============================================
Bug Fixes
----------
SCR #396 - DTMF in dialing long press not handled properly
SCR #365 - 1 Minute delay after recording from Modem or Handset channel in QuickLink
Message Center ver 3.0 appl
SCR #381 - Video Input slider in win95 mixer is reversed
SCR #378 - In Pulse dialing, 'W' and ',' are treated the same as '1'
SCR #390 - Problem with Pulse Dialing in voice mode (on some boards)
Improvements
------------
- SCR #392 - Voice rx and tx level control by register s72
- Single DMA used for MO
SmartLink Modio Version 1.51 - MARCH 17, 1998
=============================================
Bug Fixes
----------
SCR #359 - System crash upon changing AD1821 MA resources
SCR #347 - Crash in Stream manager when using System Monitor
SCR #311 - Cannot connect to Compuserve's 800 number
SCR #302 - System hangs at start of media player after Modio has been open once
SCR #299 - Connection is always made in Max rate when using the command AT+MS
SCR #362 - Audio Volume changes when Modio connects/disconnects (on some boards)
SCR #341 - Cannot connect to Juno 800 number with specific setup
SCR #275 - Sharp high pitch noise during ath1 and raising VID or AUX slide bar
Improvements
------------
A significant performance improvement has been achieved, resulting
in a lower CPU loading.
Changes
-------
Korea country selection forces now A-Low for K56Flex
SmartLink Modio Version 1.5 - MARCH 4, 1998
============================================
Changes/Bug Fixes
-----------------
SOME IMPROVEMENTS WERE MADE TO 56K PROTOCOL
SmartLink Modio Version 1.25 - February 5, 1998
===============================================
Changes/Bug Fixes
-----------------
******** - THIS VERSION SUPPORTS 56K
******** - SOME IMPROVEMENTS WERE MADE TO THE FAX
SCR #300 - Country dependent S-Regs are overridden by ATZ or AT&F
SCR #266 - 1821 problem when full duplex works using DirectSound
SCR #274 - Tx a fax from Apache to Modio, fails during training
SCR #258 - Receiving a fax after answering in voice mode
SCR #57 - ATD command does not support @ , !
SCR #184 - Call Forwarding feature doesn't work in MSphone application
SCR #277 - Modem hangs up after 15 min due to a graphic card
SCR #331 - Shutdown Problem using S3 VIRGE and VREG card
SCR #326 - Answer Tone (2100 ) Level too high
SCR #313 - Flash feature isn't working on some designs
SmartLink Modio Version 1.24 - November 30, 1997
=================================================
Changes/Bug Fixes
-----------------
- SCR #203 - When dialing from Phone Dialer, sometimes the other side can't hear you
- SCR #278 - Adjust default values for S6,S7 for Korean PTT, HS Record level for Canadian PTT
- SCR #265 - When calling Modio using Connectix VP appl, ring isn't detected by appl.
- - Low rate connections problem - improved decision for 24000/26400 & 26400/28000
SmartLink Modio Version 1.23 - October 22, 1997
=================================================
Changes/Bug Fixes
-----------------
- SCR #243 - Microphone is muted when switching from handset to speakerphone
- SCR #256 - Sometimes voice modem can't accept calls
- SCR #266 - Problem when using DirectSound in full duplex mode
The new Key:
HandsetRecordingGain [128]
CallProgWaitForDialTone [2] /// Sec (sreg 6)
CallProgWaitForCarrier [60] /// Sec (sreg 7)
SmartLink Modio Version 1.22 - September 30, 1997
=================================================
Changes/Bug Fixes
-----------------
- SCR #186 - Monitor Incoming call in Bitware
- SCR #189 - Connectix Videophone recognizes Modio
- SCR #193 - Support partial Dialing (;)
- SCR #207 - Quicklink Message Center recognizes Modio
- SCR #218 - Dialtone isn't detected when Modio dial out to TNC Mertz modem using HyperTerm
- SCR #221 - Fax Tx problem with TNC Mertz using RingCentral appl.
- SCR #230 - Fax Connects in 2400 bps
- SCR #231,#232, #235, #236 - Fax Sending problems with Murrata/Panafax
- SCR #233, #234 - Fax Tx/Rx problems with PCTEL 288 fax/modem card using BitWare appl
- SCR #237 - Ring is not detected after playing back a message through the handset
- SCR #239 - Connection fails when trying to connect with no automode
- SCR #240 - ATW does not work properly
- SCR #241 - V34 33.600 connection problems with ZoomK56
- SLLights Modio monitor was added
- Cyrix M1,M2 processors supported
- Joystick problems in DOS Box games
ADI Singapore bug list:
- (30) - V.22 problems with USR
- (53) - hyperterminal window defocused
- (35,44-49) - Fax problems
- (33) - Dialtone isn't detected when Modio dial out to TNC Mertz modem using HyperTerm
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.