RELEASE.TXT Driver File Contents (5702_558.zip)

                           Broadcom Corporation

                           16215 Alton Parkway,

                           Irvine, CA 92619-7013



                               Release Notes

             Broadcom BCM5700 SCO OpenServer Release 5 driver

                              Version 2.2.13

                                05/23/2002





Introduction

============



This file describes the SCO OpenServer Release 5 driver for the Broadcom

NetXtreme BCM5700 series 10/100/1000 Mbps Ethernet Network Interface Controller.





Driver Software Package

=======================



The driver is released as a media image file containing the driver package. This

media image file can be copied to the target machine directly for installation,

or a floppy installation disk can be made.





Creating Floppy

===============



1. Copy the file VOL.000.000 to an SCO system.



2. Create the floppy using dd if=VOL.000.000 of=/dev/rfd0135ds18





Installing Driver

=================



Use custom or scoadmin software to install the driver from the media image or

from the floppy created above. After the package is installed, use netconfig to

add the new network adapter and configure network protocol and address. Once

the adapter is added, modify the hardware configuration in Advanced Options to

change line speed and flow control if desired. The different settings of these

parameters are listed below:



    LineSpeed:    AutoNegotiate (default) (all speeds advertised)

                  FixedHalfDduplex10

                  AutoHalfDduplex10 (only 10 Mbps half duplex advertised)

                  FixedFullDduplex10

                  AutoFullDduplex10 (only 10 Mbps full duplex advertised)

                  FixedHalfDduplex100

                  AutoHalfDduplex100 (only 100 Mbps half duplex advertised)

                  FixedFullDduplex100

                  AutoFullDduplex100 (only 100 Mbps full duplex advertised)

                  AutoHalfDduplex1000 (only 1 Gbps half duplex advertised)

                  FixedFullDduplex1000*

                  AutoFullDduplex1000 (only 1 Gbps full duplex advertised)



    FlowControl:  Off (default)

                  AutoNegotiate** (Symmetric Pause advertised)

                  RxPause

                  TxPause

                  RxPause/TxPause



*Note that 1000 Mbps (1 Gbps) full duplex fixed speed is only valid for fibre

connections. For copper twisted pair connections, 1 Gbps can only be set

through auto negotiation with a 1 Gbps link partner.



**Note that auto negotiation of flow control is only valid when the line

speed is set to auto negotiation (all speeds advertised or single speed

advertised).



A kernel rebuild and reboot is required before the new configuration

will take effect.



Jumbo Frames and Other Advanced Parameters

==========================================



Jumbo MTU sizes and other advanced tunable parameters for the BCM5700

controller are located in the file space.c in the directory

/etc/conf/pack.d/bcme. Description for each parameter is contained in space.c.

Modify the desired parameter in space.c, rebuild the kernel, and reboot the

system. Note that the MTU sizes can be individually set for each adapter in

the system whereas all other paramters apply globally to all adapters. See

the bcme man page for details.



Revision History

================

v2.2.13 (05/23/02)



- Added a new OEM ID.



v2.2.12 (05/14/02)



- Added new OEM IDs.



v2.2.11 (04/12/02)



- Added necessary delays after changing GPIOs.



v2.2.10 (04/05/02)



- Fixed 5701 fiber hang problem when booting without cable.



v2.2.9 (04/03/02)



- Added new OEM subsystem IDs.

- Fixed flow control problems when autoneg. is disabled.



v2.2.8 (03/27/02)



- Added new device IDs.



v2.2.7 (03/22/02)



- Made changes to Fiber autoneg.

- Implemented new scheme for LED modes.



v2.2.3 (02/27/02)



- Added new PCI IDs for 5702/5703.

- Added Ethernet@Wirespeed.

- Fixed parity errors on 5703 in PCIX systems.



v2.2.2 (02/07/02)



- Fixed the cable disconnection problem.



v2.2.1 (02/06/02)



- Fixed problems with 5702/5703.



v2.0.19 (10/26/01)



- Added 5702 support.



v2.0.18 (09/10/01)



- Fixed the problem of over reporting CRC errors.

- Fixed 1000 half duplex late collision problem.

- Fixed the problem of missing the first packet with fiber cards.



v2.0.15 (08/24/01)



- Fixed a hang problem on A3 Fiber cards.



v2.0.14 (08/18/01)



- Fixed a hang problem on BCM5700 NIC when set to 10Mbps.



v2.0.13 (08/13/01)



- Added latest device IDs.



v2.0.11 (08/02/01)



- Fixed a hang problem when booting up with no fibre cable connected.



v2.0.10 (08/02/01)



- Fixed fibre connection problems at boot up time.



v2.0.9 (07/21/01)



- Fixed the problem of multiple NICs sharing the interrupt.



v2.0.8 (07/19/01)



- Fixed some fibre autonegotiation problems.



v2.0.5 (07/02/01)



- Added support for new boards.



v2.0.3 (06/01/01)



- Fixed panic problem when doing flooding ping.



v2.0.2 (05/25/01)



- Added more OEM hardware support.

- Added man page.



v2.0.1 (05/23/01)



- Fixed symbol errors and other errors reported by ANT test.



v1.0.8 (05/16/01)



- Added BCM5701 support.



v1.0.7 (04/02/01)



- Fixed a symbol error reported by ANT test suite.



v1.0.6 (03/30/01)



- Added logic to free buffers on the write queue when it reaches high water

  mark.

- Added workaround for AMD Athlon systems.



v1.0.5 (03/23/01)



- Added fibre support.

- Added jumbo frames.



v1.0.4 (02/23/01)



- Fixed problems found by the ANT test suite.



v1.0.3 (02/14/01)



- First Release. 








Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web2, load: 0.84