DIAG.TXT Driver File Contents (intelnic.zip)

   Adapter diagnostics
                                                                    v1.03
Running diagnostics on Intel 82557-based adapters:
   EtherExpress(TM) PRO/100B - TX
   EtherExpress(TM) PRO/100B - T4
   EtherExpress(TM) PRO/10+ PCI
=========================================================================

Intel's diagnostic software lets you test the adapter to see if there are
any problems with the adapter hardware, the cabling, or the network.

It's a good idea to run diagnostics every time you install an adapter.
You can also use diagnostics to isolate problems during troubleshooting.


DOS and Windows* 3.1 users
==========================

Note: If you want to test the adapter with a responder on the network,
      skip to the procedure after step 5.

1  Restart your computer before loading any EtherExpress PRO/100B or
   PRO/10+ PCI adapter network drivers.
   
   Note: If drivers are installed, you must remove them or disable them
         and reboot your computer before running the diagnostic software.

2  Insert the Intel Configuration and Driver diskette into a drive,
   switch to that drive, and at the DOS prompt, type
      
      SETUP <Enter>

3  From the Board Menu, select the adapter you want to test. (If you have
   only one adapter installed, the Board Menu doesn't appear.)

4  From the Main Menu, select Test adapter. Then select Test adapter
   again. The program runs a series of tests that make sure the adapter
   is functioning properly.

5  Repeat steps 3, 4, and 5 for each adapter installed in the computer.


To test the adapter with a responder on the network
---------------------------------------------------

1  Go to a computer on the same network segment with an EtherExpress 16
   ISA, Flash32, EtherExpress PRO, EtherExpress PRO/100 PCI, PRO/100B
   PCI, or PRO/10+ PCI adapter installed.

2  If this computer already has EtherExpress adapter network drivers
   installed, restart the computer without loading them. For example, if
   the drivers are loaded from the AUTOEXEC.BAT file, add REM in front of
   each line that loads a driver. Or, boot from a DOS disk.

3  Run the diagnostics program for the adapter that's installed in the
   computer (such as SoftSet, SETUP, or PROSet).

4  From the Main menu, select the command for testing the adapter, then
   select Set up as diagnostics responder.

5  Return to the computer you want to test. Run SETUP, choose Test
   adapter, and then choose Continuous Network test.


Windows NT* users
=================

If you have not already installed new drivers from the Intel
Configuration and Drivers Disk:

1  Double-click the Network icon in the Control Panel.

2  Click the Add Adapter button.

3  Don't select an Intel adapter from the list. Instead, scroll to the
   end of the list and select:
   
   <Other> Requires disk from manufacturer.

4  Insert the Intel Configuration and Drivers disk into your floppy
   drive.

   The Intel PRO adapter setup program launches.

5  Click the Test button.

   If you've just added the adapter, the network driver won't be active
   and the diagnostics will test the adapter and its connection to the
   network.

   If you're testing an adapter that's already been installed, the
   network driver will probably be active and the diagnostics will test
   the driver. This diagnostic tracks the driver's actual network
   activity.

If you have already installed the drivers:

1    Double-click the Intel PROSet icon in the Control Panel.

2    Click Test on the window that appears.

     If you have more than one adapter, first select the adapter from the
displayed list.

   If you've just added the adapter, the network driver won't be active
   and the diagnostics will test the adapter and its connection to the
   network.

   If you're testing an adapter that's already been installed, the
   network driver will probably be active and the diagnostics will test
   the driver. This diagnostic tracks the driver's actual network
   activity.




Windows 95 users
================

Use the Intel PRO adapter setup program to test the adapter:

1    Double-click the Intel PROSet icon in the Control Panel.

2    Click Test on the window that appears.

     If you have more than one adapter, first select the adapter from the
displayed list.

When using the Intel PRO adapter setup program, you have two testing
options:

A. Test the adapter and driver together:

The adapter and driver test doesn't require you to unload the NDIS
driver.

     a.   Click Test NDIS.

     b.   When the test is complete, click OK to exit.

B.   Test the adapter hardware:

The adapter hardware test unloads the NDIS driver.

     a.   Click Unload NDIS.

     b.   After the NDIS driver unloads, click OK to continue.

     c.   When the test is complete, click OK to exit. PROSet reloads

          the driver.

     d.   Restart the computer. You must restart the computer before

          accessing any network drives.









*  Third-party trademarks are the property of their respective owners.
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web4, load: 0.72