Thank you for purchasing the Saitek X8-31 Game Controller. This readme file will give you some extra information about the products. Content: I. Installation II. Uninstallation III. Dual Game port IV. Windows 95/98 Games V. Error Handling I. Installation Before Installation 1. You must have installed DIRECTX 5.0 or above before installing the device driver. This driver is for use with Windows 95/98 only. Please follows steps below to install the dedicated driver. 1. Connect the Game Controller to your game port. 2. Quit any existing programs in use. 3. Insert the bundled diskette into drive A. 4. Click "START" at the lower left corner. 5. Click "Run...". 6. Type "A:SETUP.EXE" at the dialog and press Enter. 7. Follow instruction on the screen. Before Add and Calibrate 1. "5-8 Button" On/Off switch must be turned to "ON". Add and Calibrate the Game Controller under Windows 95/98 with dedicated device driver 1. Plug the Game Controller to your game port. 2. Click "START" at the lower left corner. 3. Click "CONTROL PANEL" from "SETTINGS". 4. Double click "Game Controllers". 5. Remove all existing Controller driver(s). 6. Click "ADD". 7. Choose "Saitek X8-31 game controller" and click "OK". Controller status shown on screen should be "OK". 8. Click "PROPERTIES". 9. Click "CALIBRATE" and follow instruction. 10.Click "APPLY" and then "OK". 11.Click "OK" to quit. Buttons Mapping 1. Make sure that the driver is installed and Game Controller is calibrated and added as mentioned above. 2. Click "START" at the lower left corner. 3. Click "CONTROL PANEL" from "SETTINGS". 4. Double click "Game Controllers". 5. Select "Saitek X8-31 Game Controller" and press "Properties" button. 6. Select "Map". 7. Map the buttons as desired and click "Apply" button and then "OK" button. II. Uninstallation Follow the steps below to uninstall the Saitek X8-31 Game Controller driver: 1. Go to control panel ->Game Controller, remove the "Saitek X8-31 Game Controller". 2. Click the "Start" button at the task bar. Select "Programs" -> "Saitek X8-31 Game Controller" -> "Uninstall Saitek X8-31 Game Controller". III. Dual Game Port In DOS analog mode a standard dual game port can support maximum 4 buttons and 4 axes such as: 1. Two 2-button joypads/joysticks for a two player gaming. 2. Single joystick with 4 buttons, analog throttle and rudder. 3. Single joypad/joystick with up to 8 buttons. In this case the 5th to 8th buttons use up the 3rd and 4th axes of the dual game port. The Saitek X8-31 Game Controller belongs to the above 3rd kind of configuration. The 5th to 8th buttons use up the 3rd and 4th axes of the dual game port. Please refer to the user manual for calibration routine under Window 95/98 joystick control panel. The Saitek 8-button game controller uses a standard 15-pin gameport connector. It works in analog mode if the Saitek 8-button driver is not being installed. IV. Windows 95/98 Games Unlike DOS, Windows 95/98 controls all the system interface. However, the generic driver comes with Windows 95/98 supports only 4 buttons. So, for most of the Windows 95/98 Games such as FIFA 98 will not natively support the use of the buttons on 3rd and 4th axes and hence you need to install a customer device driver in order to have more than 4 buttons functioning. In order to serve customer better gaming experience, we provide this device driver. With the help of the device driver, you will have extra buttons supported under Windows 95/98 properly. IV. Error Handling 1. There is no Game Controllers icon at the Control Panel. At Control Panel -> System, select the page "Device Manager". Expand the "Sound, video and game controllers". Check to see if there is any "Gameport Joystick" entry. A joystick port is a must for a joystick to operate. 2. There is no "Sound, video and game controllers" entry at the "Device Manager" page. Check firstly that the sound card has been installed proper- ly. For some motherboard with build-in sound device, user has to enable it through jumper or BIOS setting. Check secondly if drivers for the sound card has been in- stalled. If such drivers have not been installed, a message "Unknown device" will appear. There is also possibility of resource conflict. In most of the cases, I/O range for joystick port is 0200-0207. You can check this out by select "Computer" and then select "I/O" to list all the I/O resource usage. When there is I/O conflicting with the joystick port, you can select the conflicting device within the device manager and then select its "Resources" tag page. Please refer to the corresponding device manual to select a new I/O range for your device. 3. For those who are not using Plug and Play sound cards, try the following to install your sound cards. a. At Control Panel -> Add New Hardware, let the system to search if there is any new device to be installed. Remember to check for any resource conflict as some non- plug-and-Play device may cause conflict unnoticed by the system. 4. The system keeps saying that joystick is not found. Make sure that you have the most upadated joystick port driver. You may try by removing the joystick port at Control Panel -> System -> Device Manager. Reboot the sys- tem. If your joystick port is plug-and-play, it will prompt you to install or just install automatically. If your joystick port is non-plug-and -play, you will have to install it manually. Finally, make sure that you have installed the DirectX driver properly. At the time this readme is written, DirectX 5 is required. 5. Why the buttons 5 to 8 do not response ? Please calibrate the joystick as the 5-8 buttons are detected through 3rd and 4th axes. So, the clibrated data is required to determine whether the buttons 5-8 are pressed. --------------------------------END----------------------------- (c) 1998 Mega World International Ltd. an affiliate and trademark & logo licensee of Saitek Ltd. All other product names are registered trademarks or tradenames of their respective companies.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.