Ethernet PCMCIA Adapter Installation
for NetWare Server 5.0 Driver
Contents
ÍÍÍÍÍÍÍÍ
Introduction
Getting Started
First time installation from the install menu
The other time installation from the install menu
Modifying an existing NetWare 5.0 Server
Introduction
ÍÍÍÍÍÍÍÍÍÍÍÍ
This installation assumes that the PC Card drivers are working
properly. Please consult INST_DOS.TXT for help with PC Card
Drivers. Getting Started will describe the installation
instructions.
Getting Started
ÍÍÍÍÍÍÍÍÍÍÍÍÍÍ
******************************************************************
* Notes: *
* The PC Card should be enabled by Card services. *
* Please run ENEP16.EXE before starting Client 32 for *
* DOSWIN. *
* *
* Two alternatives to enable the Ethernet PCMCIA Adapter: *
* 1. Modify CONFIG.SYS *
* *
* Add the following two lines to the CONFIG.SYS file *
* *
* DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-D7FF *
* DEVICE=<PATH>\ENEP16.EXE /iop=300 /irq=3 *
* ; <PATH> is a directory that includes the ENEP16.EXE *
* ; file. *
* ; The first line is optional. *
* ; Please refer to the INST_DOS.TXT file for details. *
* *
* 2. Issue an executive file: *
* *
* At the DOS prompt, type: *
* ENEP16 [/irq:X] [/iop:XXX] *
* *
* For more details, refer to inst_dos.txt. *
******************************************************************
First time installation from the install menu
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Start the NetWare Server.
> CD \NWSERVER
> SERVER
Execute "LOAD NWCONFIG" after booting up. Type:
LOAD NWCONFIG
Select "Driver Options", -> "Configure network drivers", and
-> "Select a driver".
Press <Insert> key to install an unlisted driver.
Please insert release driver diskette into floppy disk.
Press <F3> to specify a different <PATH>. <PATH> is directory
which include both EP16.LAN and EP16.LDI
Ex. A:\NETWARE\SERVER\NW50
Select "EP16.LAN ....".
Select "Save parameters and load driver" after configuring adpter
setting.
NetWare server will loading/binding driver automatically.
Specify "I/O port" and "Interrupt number" while NetWare server is
loading the driver, and these values should be consistent with the
values set by ENEP16.EXE.
After the driver has been loaded, check whether all the frame types
you want are specified for this driver in AUTOEXEC.NCF.
The other time installation from the install menu
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Start the NetWare Server.
> CD \NWSERVER
> SERVER
Execute "LOAD NWCONFIG" after booting up. Type:
LOAD NWCONFIG
Select "Driver Options", -> "Configure network drivers", and
-> "Select a driver".
Select "EP16.LAN ...." in Select a driver window.
Select "Save parameters and load driver" after configuring adpter
setting.
NetWare server will loading/binding driver automatically.
Specify "I/O port" and "Interrupt number" while NetWare server is
loading the driver, and these values should be consistent with the
values set by ENEP16.EXE.
After the driver has been loaded, check whether all the frame types
you want are specified for this driver in AUTOEXEC.NCF.
Modifying an existing NetWare 5.0 Server
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Please insert release driver diskette into floppy disk.
Copy all provided LAN files into your dos directory
which include SERVER.EXE.
>COPY <PATH>\*.* C:\NWSERVER
<PATH> here is the directory where EP16.LAN and EP16.LDI
reside.
Ex. >COPY A:\NETWARE\SERVER\NW50\EP16.LAN C:\NWSERVER
>COPY A:\NETWARE\SERVER\NW50\EP16.LDI C:\NWSERVER
Start the NetWare Server.
> CD \NWSERVER
> SERVER
From the Novell Server side, execute "LOAD NWCONFIG". Type:
LOAD NWCONFIG
Select <NCF files Options>
Select <Edit AUTOEXEC.NCF file>
Add below item into the server's AUTOEXEC.NCF file.
LOAD C:\NWSERVER\EP16 PORT=300 INT=3 FRAME=Ethernet_802.3
NAME=EP16_1_E83
BIND IPX EP16_1_E83 NET=xxxx
LOAD C:\NWSERVER\EP16 PORT=300 INT=3 FRAME=Ethernet_802.2
NAME=EP16_1_E82
BIND IPX EP16_1_E82 NET=xxxx
LOAD C:\NWSERVER\EP16 PORT=300 INT=3 FRAME=Ethernet_II
NAME=EP16_1_EII
BIND IPX EP16_1_EII NET=xxxx
LOAD C:\NWSERVER\EP16 PORT=300 INT=3 FRAME=Ethernet_SNAP
NAME=EP16_1_ESP
BIND IPX EP16_1_ESP NET=xxxx
Note: the PORT and INT parameters should be set as the values
which are set by ENEP16.EXE.
Restart the server again.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.