Workstation for DOS ODI Client Introduction: ------------- This document describes the procedure to setup the NetWare v3.X, v4.X, 5.0 workstation driver for AOPen AOP-330 10/100Mbps Cardbus Adapter. Location of Driver: \NWCLIENT\A330.COM Getting Start: -------------- 1. For the PC that installing EMM386.EXE in the CONFIG.SYS. Please make sure the memory range D000-D7FF is excluded. Ex: DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-D7FF 2. Copy A:\ENABLER\*.* to your hard disk Ex: copy A:\ENABLER\*.* C:\ENABLER 3. Add a line @CALL C:\ENABLER\CBEN.BAT on the first line of AUTOEXEC.BAT file. Sample Configuration Files: --------------------------- STARTNET.BAT: LSL A330 IPXODI NETX or VLM (VLM's for NetWare 4.x, 5.0) NET.CFG: LINK DRIVER A330 MEDIUM MM --where MM is one of AUTO, 10HALF, 10FULL, 100HALF, and 100FULL, to specifiy the media type. BUSNO NN --where NN is the PCI bus identifier of the PCI bus which connects to the adapter. DEVICENO NN --where NN is the specific PCI BIOS device identification number of the specified PCI adapter. [ or you can use "EtherID" to select a specific A330 adapter: EtherID 006067NNNNNN --Where 006067NNNNNN specify a A330 adapter's node address. This is only required when more than one A330 adapters exist on one system. ] FRAME Ethernet_802.2 --Specify frame type FRAME Ethernet_802.3 FRAME Ethernet_SNAP FRAME Ethernet_II NetWare DOS Requester FIRST NETWORK DRIVE = F NETWARE PROTOCOL = NDS BIND PREFERRED SERVER = NW411 Setup Procedures for NetWare 3.12 Client: ----------------------------------------- Before you start with the installation process, make sure that the adapter is properly installed and configured. Make sure that your NetWare workstation is properly installed. 1. Copy A330.COM from the A330 Driver Disk subdirectory A:\NWCLIENT to your harddisk. 2. Update STARTNET.BAT batch file as sample above 3. Edit the NET.CFG file that you copied over. Edit the file per your requirements (see examples above). If there are two frame types listed, whichever frame type is listed first, that is the one that the driver will load. See above for examples. The NET.CFG file should be in the same directory with the LSL.COM file. Setup Procedures for NetWare 4.X, 5.0 Client with vlm: ------------------------------------------------------ 1. Make a new directory NWCLIENT(or other name) on C drive 2. Copy A:\NWCLIENT\*.* to C:\NWCLIENT\*.* 3. Create STARTNET.BAT batch file as sample above 4. Add a line "@CALL C:\NWCLIENT\STARTNET.BAT"(ingore symbol "") on the first line of AUTOEXEC.BAT file. NOTE: ----- 1. Be sure LASTDRIVE=Z in your CONFIG.SYS file for the network mappings to work properly. 2. When you have multiple A330 Adapters on your system: Use "BUSNO" and "DEVICENO" KEYWORD in NET.CFG to select which adapter to use with your netware client. (or you can use "EtherID") -- End --Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.