Server Driver for NetWare 5.00
Introduction:
-------------
This document describes the procedure to install the NetWare v5.00
server driver for AOPen AOP-330 10/100Mbps Cardbus Adapter.
Location of Driver: \NWSERVER\500\A330.LAN
Getting Start:
--------------
1. For the PC that installing EMM386.EXE in the CONFIG.SYS.
Please make sure the memory range D000-D7FF is excluded.
Ex:
DEVICE=C:\DOS\EMM386.EXE NOEMS X=D000-D7FF
2. Copy A:\ENABLER\*.* to your hard disk
Ex:
copy A:\ENABLER\*.* C:\ENABLER
3. Add a line
@CALL C:\ENABLER\CBEN.BAT
on the first line of AUTOEXEC.BAT file.
Installation Procedure:
-----------------------
Before you start with the installation process, make sure that
the Novell NetWare v5.00 server is properly installed.
Similarly, your adapter should also be properly installed in your
server.
A. First time installation from the install menu
1. Start the NetWare Server.
> CD \NWSERVER
> SERVER
2. Execute "LOAD NWCONFIG" after booting up. Type:
LOAD NWCONFIG
3. Select "Driver options", -> "Configure network drivers", and
-> "Select a driver".
4. Press <Insert> key to install an unlisted driver.
5. Please insert release driver disk into floppy.
6. Press <F3> to specify a different <PATH>. <PATH> is directory
which include both A330.LAN and A330.LDI
Ex. A:\NWSERVER\500
7. Select "A330.LAN ...".
8. Select "Save parameters and load driver" after configuring
adapter setting.
9. NetWare server will loading/binding driver automatically.
10. After the driver has been loaded, check whether all the frame
types you want are specified for this driver in AUTOEXEC.NCF.
B. The other time installation from the install menu
1. Start the NetWare Server.
> CD \NWSERVER
> SERVER
2. Execute "LOAD NWCONFIG" after booting up. Type:
LOAD NWCONFIG
3. Select "Driver options", -> "Configure network drivers", and
-> "Select a driver".
4. Select "A330.LAN ..." in Select a driver window.
5. Select "Save parameters and load driver" after configuring
adapter setting.
6. NetWare server will loading/binding driver automatically.
7. After the driver has been loaded, check whether all the frame
types you want are specified for this driver in AUTOEXEC.NCF.
C. Modifying an existing NetWare 5.00 Server
1. Insert driver disk into floppy.
2. Copy all provided LAN files into your dos directory
which include SERVER.EXE.
Ex. >COPY A:\NWSERVER\500\A330.LAN C:\NWSERVER
>COPY A:\NWSERVER\500\A330.LDI C:\NWSERVER
3. Start the NetWare Server.
> CD \NWSERVER
> SERVER
4. From the Novell Server side, execute "LOAD NWCONFIG". Type:
LOAD NWCONFIG
Select <NCF files options>
Select <Edit AUTOEXEC.NCF file>
5. Add the following commands into the server's AUTOEXEC.NCF file.
LOAD C:\NWSERVER\A330 SLOT=1 FRAME=Ethernet_802.3 NAME=A330_1_E83
BIND IPX A330_1_E83 NET=1111
LOAD C:\NWSERVER\A330 SLOT=1 FRAME=Ethernet_802.2 NAME=A330_1_E82
BIND IPX A330_1_E82 NET=1113
LOAD C:\NWSERVER\A330 SLOT=1 FRAME=Ethernet_SNAP NAME=A330_1_ESP
BIND IPX A330_1_ESP NET=1115
LOAD C:\NWSERVER\A330 SLOT=1 FRAME=Ethernet_II NAME=A330_1_EII
BIND IPX A330_1_EII NET=1117
Note: The SLOT parameter should be set as the number of the PCI slot
on which A330 resides.
6. Restart the server again.
NOTES:
------
1. Installing Multiple LAN Adapters:
The keyword "SLOT" is provided for multiple LAN adapters in a
single server by the driver A330.LAN. So, add "SLOT" in LOAD
commands. For example:
LOAD A330 SLOT=1 FRAME=Ethernet_802.2 NAME=LAN_A
BIND IPX TO LAN_A NET=111
LOAD A330 SLOT=2 FRAME=Ethernet_802.2 NAME=LAN_B
BIND IPX TO LAN_B NET=222
2. Use keyword AUTO, 100FULL, 100HALF, 10FULL, 10HALF to specify the
media type of the A330.
For example:
; Specify AUTO-DETECT
LOAD A330 AUTO FRAME=Ethernet_802.2 NAME=LAN_A
BIND IPX TO LAN_A NET=111
; Specify 100Mbps, Half-duplex
LOAD A330 100HALF FRAME=Ethernet_802.2 NAME=LAN_A
BIND IPX TO LAN_A NET=111
The default media type is auto-detect(i.e. none of these keywords
is specified).
3. Installing One LAN adapter with Multiple Frame Types:
When binding multiple frame types to one adapter, enter a LOAD
and BIND statement for each frame type. Each LOAD statement will
use a different network number on the bind statement.
It is required to supply a name on each load line in order to
avoid being prompted for which board to bind IPX to. If you do
not have the name option in the AUTOEXEC.NCF, it will not execute
completely without user intervention.
Example:
LOAD A330 FRAME=ETHERNET_802.3 NAME=A330_1_E83
BIND IPX TO A330_1_E83 NET=11111
LOAD A330 FRAME=ETHERNET_802.2 NAME=A330_1_E82
BIND IPX TO A330_1_E82 NET=33333
LOAD A330 FRAME=ETHERNET_SNAP NAME=A330_1_ESP
BIND IPX TO A330_1_ESP NET=55555
LOAD A330 FRAME=ETHERNET_II NAME=A330_1_EII
BIND IPX TO A330_1_EII NET=77777
If problems occur during the binding process, your screen will prompt
you with error messages. Please refer to your NetWare 386 manual for
details on these messages.
-- End --
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.