PACKET.TXT Driver File Contents (aon325v22.zip)

   Packet Driver

   Introduction:
   -------------
   This document describes the procedure to setup the Packet driver for
   AOpen AON-325 10/100M Fast Ethernet PCI Adapter.

   Location of Driver:     A:\PKTDRV\AON325.COM

 
   Notes:
   ------
     1.  Load the packet driver using the software interrupt and any
         optional switches if required.

         Usage: AON325 [options] <software_int_no> [media type]

         Example: AON325 -i 0x7e

         The only required parameter is the software interrupt. A packet
         driver needs to have a software interrupt assigned to it for other
         programs to access it. The recommended interrupt 0x7e. If you need
         any of the options listed below, place them before the software
         interrupt on the command line.

         -i - Force driver to report itself as 802.3 instead of Ethernet II.
         -d - Delayed initialization. Used for diskless booting
         -n - NetWare conversion. Converts 802.3 packets into 8137 packets
         -w - Windows hack, obsoleted by winpkt
         -p - Promiscuous mode disable
         -h - Help
         -u - Uninstall

      2. Media type can be used to force the card to work on specific
         speed and duplex mode. If no media type if specified, then
         driver will read hardware configuration from EEPROM on the
         card. The hardware configuration can be modified by running
         'SETUP' on driver disk.

      3. Type command, C:\AON325 0x60, the screen will appear following
         message:

         Packet driver for AON-325 10/100M Fast Ethernet PCI Adapter version 3.17
         (c)Copyright 2000 AOpen Inc. All rights reserved.

         Line Speed 100 Mbps
         Half Duplex
         System: [345]86 processor, PCI bus, Two 8259s
         Packet driver software interrupt is 0x60
         Interrupt number is 0xA
         I/O port is 0xE000
         My Ethernet address is 00:50:BA:D0:17:EB

      4. Installing Multiple LAN Adapters:

         If there are multiple network cards on the main board, the user
         run AON325 0x60 directly, then the screen will display :

         Packet driver for AON-325 10/100M Fast Ethernet PCI Adapter version 3.17
         (c)Copyright 2000 AOpen Inc. All rights reserved.

         There are 2 network cards on your main board :
         Card 1. SlotNo= 0xA. IRQ= 0xC  I/O= 0xE000  NodeID= 00:50:BA:D0:17:31
         Card 2. SlotNo= 0xB. IRQ= 0xA  I/O= 0xD800  NodeID= 00:50:BA:D0:17:EB
         Please select a Card No.(1-2): 1

         Line Speed 100 Mbps
         Half Duplex
         System: [345]86 processor, PCI bus, Two 8259s
         Packet driver software interrupt is 0x60
         Interrupt number is 0xC
         I/O port is 0xE000
         My Ethernet address is 00:50:BA:D0:17:31

                                               -- End of File --


Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: ftp, load: 1.47