ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º º
º RELIA RE2408 PCMCIA Ethernet Adapter Drivers Series º
º º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
Jul. 1997
Table of Contents
=================
1.0 Introduction
1.1 Contents of the Relia PCMCIA Installation Diskette
2.0 Installation and Configuration with the INSTALL Program
2.1 Overview of the INSTALL Program
2.2 What You Need Before Running INSTALL
2.3 How to Run the INSTALL Program
3.0 Manually Installing and Configuring the Enabler
3.1 Overview of Enabling Software
3.2 Manually Installing the Enabling Software for DOS
3.2.1 Overview of the Enabler --- ENABLER.EXE
3.2.2 Usage of ENABLER.EXE in CONFIG.SYS
3.2.3 Usage of ENABLER.EXE from the DOS Prompt
3.2.4 Caution
3.3 Manually Installing the Enabling Software for OS/2
3.3.1 Overview of the Direct Enabler --- DIRECTEN.OS2
3.3.2 Usage of DIRECTEN.OS2 in CONFIG.SYS
3.4 Installing the Client Driver Manually Under Card and Socket
Services
3.4.1 Overview of Client Driver --- CSDRIVER.EXE
3.4.2 The Usage of CSDRIVER.EXE in CONFIG.SYS File
3.4.3 The Usage of CSDRIVER.EXE under DOS Prompt
3.4.4 Caution
4.0 Manually Installing and Configuring the Network Drivers
5.0 Diagnostic --- DIAG.EXE
6.0 Installing client Driver under SystemSoft's CardSoft
1.0 Introduction
Thank you for purchasing the Relia PCMCIA Ethernet Card for Notebook
and Palmtop PCs.
The Relia PCMCIA Ethernet Card is a Novell NE2000-compatible 16-bit
network adapter for the PCMCIA 2.0 bus featuring both 10Base2 and
10Base-T media auto-detecting ports.
1.1 The Contents of Relia PCMCIA Installation Diskette
The files contained in this diskette are given below. This diskette
contains the driver programs necessary to use the card under Novell
NetWare, Windows for Workgroups, MS LAN Manager, Windows NT, Windows
95, Banyan VINES, DECnet Pathworks, IBM LAN Server, Packet Driver
for TCP/IP applications, Artisoft LANtasti network operating
systems.
The driver programs on this diskette are divided into the following
subdirectories. Each directory contains a README.TXT file with
detailed installation instructions.
Directory/Files Contents
--------------- --------------------------------------------------
DISK1 It is used by the OEMSETUP.INF file.
README.TXT This file contains the additional information.
INSTALL.EXE Installation program.
NETPCM.INF Information file for Windows 95 driver
installation
PCMWIN95.SYS Driver for Window 95
PCMNT40.SYS Driver for Windows NT 4.0
OEMSETUP.INF Information file for Windows NT 4.0 driver
installation
PCMNT40.DLL Dynamic Linking Library for Windows NT 4.0
installation
\DIAG\DIAG.EXE PCMCIA Ethernet Card diagnostic software.
\ENABLER
ENABLER.EXE Direct enabler and client driver for DOS.
DIRECTEN.OS2 Direct enabler for OS/2.
\NETWARE\CLIENT ODI workstation driver for Novell NetWare version
3.x and 4.x.
\NDIS2
WFW311 NDIS 2.0 driver for Windows for Workgroups 3.11.
WFW31 NDIS 2.0 driver for Windows for Workgroups 3.1.
MSLANMAN.DOS NDIS 2.0 driver for MS LAN Manager 2.x for DOS.
MSLANMAN.OS2 NDIS 2.0 driver for MS LAN Manager 2.x for OS/2.
BANYAN NDIS 2.0 driver for Banyan VINES for DOS.
PATHWORK NDIS 2.0 driver for DECnet Pathworks.
OS2_WARP NDIS 2.0 driver for LAN Server for OS_Warp
\LANTASTI NDIS 2.0 driver for Artisoft LANtastic 6.x.
\PKTDRV Packet driver.
2.0 Installing and Configuring with the INSTALL Program
The INSTALL program contained on this installation diskette can help
you easily install and configure your Relia PCMCIA Ethernet Card and
network operating system. If the INSTALL program does not work
correctly please install and configure the enabler and network
operating system files manually.
Installation of the enabler is described in section 3. Installation
of the network operating system drivers is described in README.TXT
files in each of the appropriate directories.
2.1 Overview of the INSTALL Program
A. Can auto-configure the Relia PCMCIA Ethernet Card for most
notebook computers.
B. Can modify some Networking Operating System files that are
necessary for your Relia PCMCIA Ethernet Card under the following
networking systems:
Novell Netware
Microsoft LAN Manger
Microsoft Windows for Workgroups
Artisoft LANtastic v6.x
Packet Driver
C. Can copy the proper files to the subdirectories where the network
operating system files are installed.
2.2 What You Need Before Running INSTALL
A. Before installing your Relia PCMCIA Ethernet Card, you must first
make sure that your network operating system is already installed.
B. Make sure that the Relia PCMCIA Ethernet Card has been inserted
into your system's PCMCIA socket.
2.3 How to run INSTALL program
To run INSTALL, at the DOS prompt type:
A:\>INSTALL
Read each screen carefully and respond appropriately to each prompt.
3.0 Manually Installing and Configuring the Enabling Software
3.1 Overview of Enabling Software
As with other PCMCIA devices, the Relia PCMCIA Ethernet Card must
be enabled by a software program before it can be used.
There are two kinds of PCMCIA enabler software:
* Direct Enablers.
* Card and Socket Services client drivers.
Whenever the card has been powered off (when the card is removed
or the computer goes into "sleep" mode), the direct enabler must
be executed again.
3.2 Installing the Enabling Software Manually
3.2.1 Overview of the Enabler --- ENABLER.EXE
The ENABLER.EXE program provides both direct enabler and
client driver functions.
If you do not have card and socket service software installed,
you should install direct enabler to enable your Relia PCMCIA
Ethernet Card.
The enabler ENABLER.EXE program contained on this disk is used
both as a device driver used in your computer's CONFIG.SYS file,
and also as an executable program run from the DOS prompt.
This version will directly configure the Relia PCMCIA Ethernet
Card for the following PCMCIA controllers:
Intel 82365SL (and compatibles)
Vadem VG-365/465
Cirrus Logic
Databook TCIC
Sharp PHIC
IBM ThinkPad
Toshiba 3300
and act as client driver when the Socket Services and Card
Services presented in your system.
ENABLER.EXE can also enable the card using Socket Services
versions 1.xx and 2.xx, if Socket Services is present but Card
Services is not.
3.2.2 Using ENABLER.EXE in CONFIG.SYS
You can create or modify your system's CONFIG.SYS using a text
editor.
The enabler CONFIG.SYS command line has the format:
without Socket Services and Card Services installed:
DEVICE=[path]\ENABLER.EXE [/IRQ=x] [/MEM=mm] [/IO=nnn]
with Socket Services and Card Services installed:
DEVICE=[path]\ENABLER.EXE [/IRQ=x] [/IO=nnn]
where [path] is the drive and pathname of the directory
containing DIRECTEN.EXE.
Valid options:
x = Interrupt number (3, 4, 5, 9, 10, 11, 12, 15)
mm = Hex memory location (e.g. C0, C8, D0, D8)
nnn = IO range (300, 320, 340, 360)
3.2.3 Using ENABLER.EXE from the DOS Prompt
The enabler DOS command line has the format:
without Socket Services and Card Services installed:
ENABLER [/IRQ=x] [/MEM=mm] [/IO=nnn] [/SKT=z] [/O] [/?]
with Socket Services and Card Services installed:
ENABLER [/IRQ=x] [/IO=nnn] [/?]
Valid options:
x = Interrupt number (3, 4, 5, 9, 10, 11, 12, 15)
mm = Hex memory location (e.g. C0, C8, D0, D8)
nnn = IO range (300, 320, 340, 360)
z = Socket (0 to 7).
/O (overwrites current socket settings).
/? Displays this screen.
Note: if the /SKT parameter is omitted, ENABLER.EXE will
automatically detect the socket where the card is
inserted.
3.2.4 Cautions
A. If socket servives presented in your system, you should add
the ENABLER.EXE utility line in CONFIG.SYS after the lines
for card and socket services utilities.
B. If you add the "DEVICE=[path]\ENABLER.EXE ...." line after
any memory management software, you should tell the memory
manager to exclude the memory area set by /MEM=mm parameter.
Consult the following table to determine what memory address
ranges to exclude:
Setting Range
/MEM=C0 X=C000-C7FF
/MEM=C8 X=C800-CFFF
/MEM=D0 X=D000-D7FF
/MEM=D8 X=D800-DFFF
Note: Only applicable to the case "without Socket Services
and Card Services installed"
B. If Socket Services software is installed, but Card Services
is not, you should add the "DEVICE=[path]\ENABLER.EXE ... "
line after the Socket Services software DEVICE= line.
3.3 Installing the Enabling Software Manually for OS/2
3.3.1 Overview of the Direct Enabler --- DIRECTEN.OS2
If you do not have card and socket service software installed,
you should install the direct enabler to enable your Relia
PCMCIA Ethernet Card.
The direct enabler DIRECTEN.OS2 program contained on this disk
is used as a device driver used in your computer's CONFIG.SYS
file.
This version will directly configure the Relia PCMCIA Ethernet
Card for the following PCMCIA controllers:
Intel 82365SL (and compatibles)
Vadem VG-365/465
Cirrus Logic
Databook TCIC
Sharp PHIC
IBM ThinkPad
Toshiba 3300
Configuration is also possible via Socket Services versions 1.xx
and 2.xx.
3.3.2 Using DIRECTEN.OS2 in CONFIG.SYS
You can create or modify your system's CONFIG.SYS using a text
editor.
The direct enabler CONFIG.SYS command line has the format:
DEVICE=[path]\DIRECTEN.EXE [/IRQ x] [/MEM mm] [/IO nnn] [/SKT z]
where [path] is the drive and pathname of the directory
containing DIRECTEN.OS2.
Valid options:
x = Interrupt number (3, 4, 5, 9, 10, 11, 12, 15)
mm = Hex memory location (e.g. C0, C8, D0, D8)
nnn = IO range (300, 320, 340, 360)
z = Socket (0 to 7).
Note: if the /SKT parameter is omitted, DIRECTEN.OS2 will
automatically detect the socket where the card is inserted.
4.0 Manually Installing and Configuring the Network Drivers
You can find additional information about network device drivers in
the README.TXT files located in each of the respective
subdirectories.
5.0 Diagnostic --- DIAG.EXE
DIAG.EXE will run the following test to make sure the hardware
components of your Relia RE2408 PC Card are functional:
I/O Port Assignment
NIC Register Access
On-board RAM Buffer Test
Lookback through ENC
Lookback through ENA
Lookback to UTP
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
Technical Support
===================
If you have any questions about installing or using the adapter
drivers, check the README.TXT in the directory corresponding to your
installed driver.
If you need further assistance or technical support, please contact
your dealer or the following Relia Technologies office:
Taiwan Address: 1F, No. 24, Industry E. 9th Road
Science-Based Industrial Park
Hsinchu, Taiwan, R.O.C.
E-Mail: support@relia1.relia.com.tw
Fax: +886-3-5774-220
BBS: +886-3-5788-086 (14400bps/8/N/1)
TEL: +886-3-5774-222
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.