; OEMSETUP FILE FOR OSITECH CardBus Ethernet Adapters
;
; Copyright (c) Ositech Communications, Inc. 1997-1999
; All rights reserved.
;
; Ositech Communications, Inc.
; 679 Southgate Drive,
; Guelph, Ontario N1G 4S2
; CANADA
;
; fwbent@ositech.com
;
; Supported adapters:
; Seven of Spades Trumpcard
; Queen of Spades Trumpcard
; Jack of Spades Trumpcard
;
; Usage:
;
; This file is the installation/configuration/deinstallation
; procedure of the OTCCBDRV driver for Windows NT. It can be
; called from Windows Setup directly, or via the Windows NT
; Networks Control Program Applet (NCPA) from inside the Windows
; Control Panel.
;
;
; $Date: 5/08/99 10:26a $
; $Revision: 48 $
;
;----------------------------------------------------------------------------------------
[Identification]
OptionType = NetAdapter
[PlatformsSupported]
PCI
PCMCIA
[LanguagesSupported]
ENG
[Options]
OTCCB61
OTCCB62
[ConnectionChoicesOTCCB61]
Connect_0 = "Auto Select", 0
Connect_1 = "10BASE-T (10Mbps)", 2
Connect_2 = "10BASE-T Full Duplex", 32770
Connect_3 = "100BASE-TX (100Mbps)", 8
Connect_4 = "100BASE-TX Full Duplex", 32776
Connect_5 = "PowerSave Auto Select", 65535
[ConnectionChoicesOTCCB62]
Connect_0 = "Auto Select", 0
Connect_1 = "10BASE-T (10Mbps)", 2
Connect_2 = "10BASE-T Full Duplex", 32770
Connect_3 = "100BASE-TX (100Mbps)", 8
Connect_4 = "100BASE-TX Full Duplex", 32776
Connect_5 = "PowerSave Auto Select", 65535
[OptionsTextENG]
OTCCB61 = "Ositech Seven Of Spades Trumpcard"
OTCCB62 = "Ositech Jack Of Spades Trumpcard"
[FileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. "+
"Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
ProductSoftwareDescription = "OTCCB61TX CardBus 10/100 Adapter Driver"
FunctionOTCCB61Title = "OTCCB61TX CardBus 10/100 Adapter Card Setup"
FunctionOTCCB62Title = "OTCCB62TX CardBus 10/100 Adapter Card Setup"
ProductHardwareOTCCB61Description = "Seven of Spades CardBus 10/100"
ProductHardwareOTCCB62Description = "Jack of Spades CardBus 10/100"
ConnectionList = ^(ConnectionChoices$(Option), 1)
ConnectionValues = ^(ConnectionChoices$(Option), 2)
NoList = ^(NoChoices, 1)
NoValues = ^(NoChoices, 2)
ShellCodeErrorTitle = "Error: "$(Function$(Option)Title)
ShellCodeErrorText = "Shell Code Error."
CANNOT_FIND_ANY_CARD = "Supported network card is not present in the system."
[DialogConstantsENG]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"
[FileDependentDlgENG]
DlgText = "Choose the proper cable type for the "+
"network adapter. Select [Help] for a detailled "+
"description of the available options of the list."
DlgTemplate = "ADAP_PROTO_COMBO"
DlgType = "Combination"
Caption = $(Function$(Option)Title)
Combo1Label = "Network &Media Type:"
Combo1List = $(ConnectionList)
Combo1Out = $(ConnectionValue)
ComboListItemsIn = {Combo1List}
ComboListItemsOut = {Combo1Out}
EditTextLim = ""
CBOptionsGreyed = {}
MinHelpId = 10
MaxHelpId = 1140
HelpContext = $(Help$(Option)Id)
[FileConstantsEpic]
UtilityInf = "UTILITY.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
NetEventDLL = "%SystemRoot%\System32\netevent.dll"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
Manufacturer = "OsitechCommunicationsInc"
ProductMajorVersion = "1"
ProductMinorVersion = "01"
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
VendorID = 4280 ;; 10b8 (SMC)
; VendorID = 5026 ;; 13a2 (OSITECH)
ProductSoftwareName = "OTCETHCB"
ProductSoftwareTitle = "OTCETHCB Adapter Driver"
ProductSoftwareImagePath = "\SystemRoot\System32\drivers\OTCETHCB.sys"
NetRuleSoftwareType = "OTCCB61Sys ndisDriver OTCCB61Driver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """OTCCB61Sys"" yes no container"
NetRuleSoftwareClass = {"OTCCB61Driver basic"}
NetRuleSoftwareSWBindable = {+
"OTCCB61Driver OTCCB61Adapter non exclusive 100"}
ProductHardwareName = "OTCETHCB"
ProductHardwareOTCCB61Title = "Seven of Spades CardBus 10/100"
ProductHardwareOTCCB62Title = "Jack of Spades CardBus 10/100"
NetRuleHardwareOTCCB61Type = "OTCCB61 OTCCB61Adapter"
NetRuleHardwareOTCCB62Type = "OTCCB61 OTCCB61Adapter"
NetRuleHardwareOTCCB61Class = {"OTCCB61Adapter basic"}
NetRuleHardwareOTCCB62Class = {"OTCCB61Adapter basic"}
AdapterOTCCB61Type = 5 ;; PCI board
AdapterOTCCB62Type = 5 ;; PCI board
HelpOTCCB61Id = 30
HelpOTCCB62Id = 40
OTCCB61CFID = 397496 ;; 0x000610B8
OTCCB62CFID = 397496 ;; 0x000610B8
OTCCB61SYSID = 2147619746 ;; 0x800213A2
OTCCB62SYSID = 2147881890 ;; 0x800613A2
BurstLength = 0 ;; BurstLength = 0 unlimited
OptionHelpFile = "OTCETHCB.hlp"
NetRuleHardwareBindForm = " yes yes container"
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
KeyJoSEth = "VEN_10B8&DEV_0006&SSVEN_13A2&SSDEV_8006"
KeyJoSMdm = "VEN_10B8&DEV_0006&SSVEN_13A2&SSDEV_8007"
Key7oSEth = "VEN_10B8&DEV_0006&SSVEN_13A2&SSDEV_8002"
KeyPointJoS = "Trumpcard:JoS Ethernet"
KeyPoint7oS = "Trumpcard:7oS Ethernet"
CardWizKeyName = $(!NTN_ServiceBase)"\resman\Database"
CardExecKeyName = $(!NTN_ServiceBase)"\CardS\Parameters"
CardWareKeyName = $(!NTN_ServiceBase)"\PCCS\Options"
TrayIconExe = "osigui.exe -port COM5"
[GeneralConstants]
from = ""
to = ""
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
[date]
Now = {} ? $(!LIBHANDLE) GetSystemDate
[Identify]
Debug-Output "otcinf-[Identify]"
read-syms Identification
set Status = STATUS_SUCCESSFUL
set Identifier = $(OptionType)
set Media = #("Source Media Descriptions", 1, 1)
Return $(Status) $(Identifier) $(Media)
[ReturnOptions]
Debug-Output "otcinf-[ReturnOptions]"
set Status = STATUS_FAILED
set OptionList = {}
set OptionTextList = {}
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) in $(LanguageList)
ifstr(i) $($1) == ""
goto returnoptions
endif
set PlatformList = ^(PlatformsSupported, 1)
Ifcontains(i) $($1) in $(PlatformList)
goto returnoptions
else
set Status = STATUS_NOTSUPPORTED
goto finish_ReturnOptions
endif
else
set Status = STATUS_NOLANGUAGE
goto finish_ReturnOptions
endif
returnoptions = +
set OptionList = ^(Options, 1)
set OptionTextList = ^(OptionsText$($0), 1)
set Status = STATUS_SUCCESSFUL
finish_ReturnOptions = +
Return $(Status) $(OptionList) $(OptionTextList)
[InstallOption]
Set !DebugOutputControl = 1
Debug-Output "otcinf-[InstallOption]"
set Option = $($1)
set SrcDir = $($2)
set AddCopy = $($3)
set DoCopy = $($4)
set DoConfig = $($5)
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) NOT-IN $(LanguageList)
Return STATUS_NOLANGUAGE
endif
set-subst LF = "//n"
read-syms GeneralConstants
read-syms FileConstantsEpic
set NetRuleSoftwareBindable = $($R1)
Debug-Output "otcinf-[InstallOption] R1:"$($R1)
read-syms DialogConstants$(!STF_LANGUAGE)
ifstr(i) $(!NTN_Origination) == "NCPA"
set Continue = "OK"
endif
read-syms FileConstants$(!STF_LANGUAGE)
detect date
set-title $(Function$(Option)Title)
set to = Begin
set from = Begin
set CommonStatus = STATUS_SUCCESSFUL
EndWait
Begin = +
Ifstr(i) $(!NTN_InstallMode) == deinstall
set StartLabel = removeadapter
else-Ifstr(i) $(!NTN_InstallMode) == Update
set StartLabel = UpgradeSoftware
else-Ifstr(i) $(!NTN_InstallMode) == bind
set StartLabel = bindingadapter
else-Ifstr(i) $(!NTN_InstallMode) == configure
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
else
set StartLabel = configureadapter
endif
else
set StartLabel = installadapter
set OEM_ABANDON_OPTIONS = {}
set OEM_ABANDON_SOFTWARE = FALSE
set OEM_ABANDON_ON = TRUE
endif
set from = $(fatal)
set to = $(fatal)
goto $(StartLabel)
installadapter = +
Debug-Output "otcinf- Installadapter-"
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
CloseRegKey $(KeyProduct)
ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
$(ProductVersion)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto end
else
Shell $(UtilityInf), CardExistedDlg
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) != "OK"
set CommonStatus = STATUS_USERCANCEL
goto end
endif
set OldVersionExisted = $(TRUE)
endif
Endif
ifstr(i) $(DoCopy) == "YES"
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
install "Install-Hlp"
endif
Goto installproduct
configureadapter = +
Debug-Output "otcinf- configureadapter- "
Ifstr(i) $(KeyProduct) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) == $(KeyNull)
Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Goto fatalregistry
Endif
Endif
Shell $(UtilityInf) FindService, $(KeyProduct)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Endif
Ifstr(i) $($R0) != NO_ERROR
Goto fatalregistry
endif
set KeyParameters = $($R2)
CloseRegKey $($R1)
Ifstr $(KeyParameters) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
goto fatalregistry
endif
set OldVersionExisted = $(TRUE)
set ValueName = ""
set ValueData = ""
set ValueStr = ""
set ValueList = {}
EnumRegValue $(KeyParameters) ValueList
ForListDo $(ValueList)
set ValueItem = $($)
set ValueName = *($(ValueItem),1)
set ValueData = *($(ValueItem),4)
Ifstr(i) $(ValueName) == "LineSpeed"
set ConnectionIndex = $(ValueData)
endif
ifstr(i) $(ValueName) == "AdapterName"
set OSISVC_Name = $(ValueData)
endif
EndForListDo
set ConnectionValue = *($(ConnectionList), ~($(ConnectionValues),$(ConnectionIndex)))
ifstr(i) $(ConnectionValue) == ""
set ConnectionValue = *($(ConnectionList), 2)
endif
adapteroptions = +
Debug-Output "otcinf- adapteroptions-"
set from = adapteroptions
read-syms FileDependentDlg$(!STF_LANGUAGE)
;+++
; Sept 12 1998
;
ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
ifstr(i) $(!AutoNetInterfaceType) != ""
set BusInterfaceType = $(!AutoNetInterfaceType)
else
set BusInterfaceType = 1
endif
ifstr(i) $(!AutoNetBusNumber) != ""
set BusNumber = $(!AutoNetBusNumber)
else
set BusNumber = 0
endif
goto UnattendBypass
endif
;
; Sept 12 1994
;---
SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId) $(Help$(Option)Id)
;+++
;09/24/98
OpenRegKey $(!REG_H_LOCAL) "" $(CardWizKeyName) $(MAXIMUM_ALLOWED) CardWizKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardExecKeyName) $(MAXIMUM_ALLOWED) CardExecKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardWareKeyName) $(MAXIMUM_ALLOWED) CardWareKey
Set DoOsiCBEna = "Yes"
Ifstr $(CardWizKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardWizKey)
Endif
Ifstr $(CardExecKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardExecKey)
Endif
Ifstr $(CardWareKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardWareKey)
Endif
Ifstr(i) $(DoOsiCBEna) == "Yes"
Debug-Output "otcinf- running configurator 2-"
RunProgram ProgramExitCode "" "" $(!STF_WINDOWSSYSPATH)"\otccbcfg.exe" $(OSISVC_Name)
ifint $(ProgramExitCode) == 0
set CommonStatus = STATUS_USERCANCEL
goto end
endif
Else
ui start "InputDlg"
ifstr(i) $(DLGEVENT) == "CONTINUE"
set ConnectionIndex = $(Combo1Out)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "BACK"
set CommonStatus = STATUS_USERCANCEL
ui pop 1
goto end
else
ui pop 1
goto end
endif
Endif
set ConnectionValue = *($(ConnectionValues), ~($(ConnectionList),$(ConnectionIndex)))
UnattendBypass =+
ifstr(i) $(ConnectionValue) == ""
set ConnectionValue = *($(ConnectionList), 2)
endif
ifstr(i) $(!NTN_InstallMode) == configure
goto updateparameters
endif
installproduct =+
Debug-Output "otcinf- installproduct-"
Ifint $(OldVersionExisted) == $(TRUE)
Ifstr(i) $(!NTN_InstallMode) == configure
Goto updateparameters
Endif
Endif
StartWait
set-div DeviceID = $($(Option)CFID) 65336
; Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(DeviceID)
; ifint $($ShellCode) != $(!SHELL_CODE_OK)
; goto ShellCodeError
; endif
; ifstr(i) $($R0) == {}
; set Error = $(CANNOT_FIND_ANY_CARD)
; set CommonStatus = USER_CANCEL
; set from = end
; goto nonfatal
; endif
set AdapterList = $($R0)
ifint $(OldVersionExisted) == $(FALSE)
ifstr(i) $(!NTN_InstallMode) == "install"
Ifstr(i) $(DoCopy) == "YES"
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
; install "Install-Hlp"
Endif
OpenRegKey $(!REG_H_LOCAL) "" $(CardWizKeyName) $(MAXIMUM_ALLOWED) CardWizKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardExecKeyName) $(MAXIMUM_ALLOWED) CardExecKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardWareKeyName) $(MAXIMUM_ALLOWED) CardWareKey
Set DoOsiCBEna = "Yes"
Ifstr $(CardWizKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardWizKey)
install "Install-Option"
Endif
Ifstr $(CardExecKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardExecKey)
install "Install-Softex"
Ifcontains(i) $(Option) in {"OTCCB62"}
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows\CurrentVersion\Run" $(!REG_KEY_ALL_ACCESS) KeyNt
Set TrayIconList = {OSIGUIEXE,$(NoTitle),$(!REG_VT_SZ),$(TrayIconExe)}
SetRegValue $(KeyNt) $(TrayIconList)
CloseRegKey $(KeyNt)
Endif
Endif
Ifstr $(CardWareKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardWareKey)
install "Install-Option"
Endif
ifstr(i) $(DoOsiCBEna) == "Yes"
install "Install-Option"
endif
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
endif
endif
;+++
;09/24/98
OpenRegKey $(!REG_H_LOCAL) "" $(CardWizKeyName) $(MAXIMUM_ALLOWED) CardWizKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardExecKeyName) $(MAXIMUM_ALLOWED) CardExecKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardWareKeyName) $(MAXIMUM_ALLOWED) CardWareKey
Set DoOsiCBEna = "Yes"
Ifstr $(CardWizKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardWizKey)
Endif
Ifstr $(CardExecKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardExecKey)
install "Install-Softex"
Ifcontains(i) $(Option) in {"OTCCB62"}
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows\CurrentVersion\Run" $(!REG_KEY_ALL_ACCESS) KeyNt
Set TrayIconList = {OSIGUIEXE,$(NoTitle),$(!REG_VT_SZ),$(TrayIconExe)}
SetRegValue $(KeyNt) $(TrayIconList)
CloseRegKey $(KeyNt)
Endif
Endif
Ifstr $(CardWareKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardWareKey)
Endif
ifstr(i) $(DoOsiCBEna) == "Yes"
install "Install-Hlp"
; CardWizard is not installed, well need to use Ositech enabler
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernel", "NDIS", {"osicbena"}, "",+
$(NetEventDLL)
else
; CardWizard is installed
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
$(NetEventDLL)
endif
;09/24/98
;---
Set OEM_ABANDON_SOFTWARE = TRUE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
CloseRegKey $($R4)
CloseRegKey $($R5)
goto fatalregistry
endif
Set SoftProductKey = $($R1)
Set SoftNetRuleKey = $($R2)
Set SoftServiceKey = $($R3)
Set SoftParameterKey = $($R4)
Set SoftLinkageKey = $($R5)
;+++
; 09/21/98
OpenRegKey $(!REG_H_LOCAL) "" $(CardWizKeyName) $(MAXIMUM_ALLOWED) CardWizKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardExecKeyName) $(MAXIMUM_ALLOWED) CardExecKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardWareKeyName) $(MAXIMUM_ALLOWED) CardWareKey
Set DoOsiCBEna = "Yes"
Ifstr $(CardWizKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardWizKey)
Endif
Ifstr $(CardExecKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardExecKey)
Endif
Ifstr $(CardWareKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardWareKey)
Endif
ifstr(i) $(DoOsiCBEna) == "Yes"
;
; CardWizard is not installed, well need to use Ositech enabler
;
; Create the OsiCBEna service
;
Debug-Output "otcinf- Add OSICBENA.SYS service"
Shell $(UtilityInf), CreateService,+
"osicbena",+
"OsiCBEna CardBus Enabler",+
"\SystemRoot\System32\drivers\osicbena.sys",+
"kernelauto",+
"System Bus Extender",+
{},+
""
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "otcinf- ShellCode error from CreateService"
goto ShellCodeError
endif
;
; Set the Start to 'Manual' from 'System', since kernelauto only sets Start to 1
;
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\osicbena" $(MAXIMUM_ALLOWED) MyOsicbenaHandle
Ifstr $(MyOsicbenaHandle) == $(KeyNull)
Debug-Output "otcinf- FAILURE to open osicbena key after creation!"
else
Set NewValueList = {{Start, $(NoTitle), $(!REG_VT_DWORD), 3}} ; "Start=0x00000003"
Shell $(UtilityInf), AddValueList, $(MyOsicbenaHandle), $(NewValueList)
CloseRegKey $(MyOsicbenaHandle)
Endif
; CardWizard is not installed, well need to use Ositech enabler
SetRegValue $(SoftLinkageKey) {OtherDependencies, 0, +
$(!REG_VT_MULTI_SZ), {"osicbena"}}
endif
; 09/21/98
;---
set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
{MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
{MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
{Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
goto fatalregistry
endif
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
{use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
{bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
{bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareSWBindable)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
goto fatalregistry
endif
endif
; ForListDo $(AdapterList)
; set BusNum = *($($),1)
; set DeviceNum = *($($),2)
; set FunctionNum = *($($),3)
;
; Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(BusNum), +
; $(DeviceNum), $(ProductHardware$(Option)Description), $(ProductHardwareName) "YES"
;
; ifint $($ShellCode) != $(!SHELL_CODE_OK)
; goto ShellCodeError
; endif
;
; ifstr $($R0) != "NO_ERROR"
; set Error = $($R0)
; goto fatal
; endif
;
; ifstr(i) $($R1) != "YES"
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
read-syms FileDependentDlg$(!STF_LANGUAGE)
;+++
; Sept 14 1998
;
ifstr(i) $(!STF_GUI_UNATTENDED) != "YES"
SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId) $(Help$(Option)Id)
ifstr(i) $(DoOsiCBEna) == "Yes"
Debug-Output "otcinf- running configurator 1-"
RunProgram ProgramExitCode "" "" $(!STF_WINDOWSSYSPATH)"\otccbcfg.exe" $(ProductSoftwareName)$(AdapterNumber)
ifint $(ProgramExitCode) == 0
set CommonStatus = STATUS_USERCANCEL
goto abandon
endif
else
ui start "InputDlg"
ifstr(i) $(DLGEVENT) == "CONTINUE"
set ConnectionIndex = $(Combo1Out)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "BACK"
set CommonStatus = STATUS_USERCANCEL
ui pop 1
goto abandon
else
ui pop 1
goto abandon
endif
set ConnectionValue = *($(ConnectionValues), ~($(ConnectionList),$(ConnectionIndex)))
endif
endif
;
; Sept 14 1994
;---
Set HardNetCardKey = $($R1)
Set HardNetRuleKey = $($R2)
Set HardParameterKey = $($R3)
set AdapterNumber = $($R4)
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set BusTypeNum = 5
Ifstr $(OldAdapterName) == ""
set OldAdapterName = $(ProductHardwareName)$(AdapterNumber)
Endif
set NewValueList = {{AdapterType,$(NoTitle),$(!REG_VT_DWORD),$(Adapter$(Option)Type)},+
{AdapterName,$(NoTitle),$(!REG_VT_SZ),$(OldAdapterName)},+
{MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
{BurstLength,$(NoTitle),$(!REG_VT_DWORD),$(BurstLength)},+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
{ProductId,$(NoTitle),$(!REG_VT_DWORD),$($(Option)CFID)},+
{SystemId,$(NoTitle),$(!REG_VT_DWORD),$($(Option)SYSID)},+
{MaxTransmits,$(NoTitle),$(!REG_VT_DWORD),8},+
{MaxReceives,$(NoTitle),$(!REG_VT_DWORD),64},+
{ExtraReceives,$(NoTitle),$(!REG_VT_DWORD),64},+
; {IpgDelay,$(NoTitle),$(!REG_VT_DWORD),3},+
{BurstLength,$(NoTitle),$(!REG_VT_DWORD),0},+
{EarlyTXOff,$(NoTitle),$(!REG_VT_DWORD),1},+
{EarlyRXOff,$(NoTitle),$(!REG_VT_DWORD),0},+
{ReadMultiple,$(NoTitle),$(!REG_VT_DWORD),1},+
; {PciLatencyTimer,$(NoTitle),$(!REG_VT_DWORD),64},+
; {InterruptMitigation,$(NoTitle),$(!REG_VT_DWORD),0},+
{TransmitThreshold10,$(NoTitle),$(!REG_VT_DWORD),64},+
{TransmitThreshold100,$(NoTitle),$(!REG_VT_DWORD),256},+
{ReceiveThreshold,$(NoTitle),$(!REG_VT_DWORD),128},+
{Pcmcia,$(NoTitle),$(!REG_VT_DWORD),1},+
{ScrambleOn,$(NoTitle),$(!REG_VT_DWORD),0}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
; ifint $($(Option)CFID) == $(DC21041CFID)
;
; set NewValueList = {{SnoozeMode,$(NoTitle),$(!REG_VT_DWORD),0}}
;
; Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
; ifint $($ShellCode) != $(!SHELL_CODE_OK)
; goto ShellCodeError
; endif
; endif
;
; ifint $($(Option)CFID) == $(DC21140CFID)
;
; set NewValueList = {{StoreAndForward,$(NoTitle),$(!REG_VT_DWORD),1},+
; {TransmitThreshold,$(NoTitle),$(!REG_VT_DWORD),512}}
;
; Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
;
; ifint $($ShellCode) != $(!SHELL_CODE_OK)
; goto ShellCodeError
; endif
; endif
;
; OTCETHCB: add the comm port info to the SYSTEM\CurrentControlSet\Services\Serial\Parameters section of the registry
;
; +++ -fwb-
Set ComPortValue = "COM5" ;
Set COMInterruptNumber = 10 ;
Set COMIoBaseAddrValue = 4352 ; 0x1100
Ifcontains(i) $(Option) in {"OTCCB62"}
Debug-Output "otcinf- addserialport-"
Ifstr(i) $(ComPortValue) != "None"
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters\SerialOsitechJOS" $(MAXIMUM_ALLOWED) MyNewSerialHandle
Ifstr $(MyNewSerialHandle) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialKey
CreateRegKey $(SerialKey) {"SerialOsitechJOS",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyNewSerialHandle
CloseRegKey $(SerialKey)
Endif
Set NewValueList = {{DosDevices, $(NoTitle), $(!REG_VT_SZ), $(ComPortValue)},+ ; "COMx"
{ForceFifoEnable,$(NoTitle), $(!REG_VT_DWORD), 1},+ ; Always true for JOS
{BusType, $(NoTitle), $(!REG_VT_DWORD), 5},+ ; PCIBus
{BusNumber, $(NoTitle), $(!REG_VT_DWORD), 0},+ ; Must be zero for WinNT
{InterruptMode, $(NoTitle), $(!REG_VT_DWORD), 0},+ ; Shareable
{ProductId,$(NoTitle),$(!REG_VT_DWORD),$($(Option)CFID)},+
{SystemId,$(NoTitle),$(!REG_VT_DWORD),$($(Option)SYSID)}}
Shell $(UtilityInf), AddValueList, $(MyNewSerialHandle), $(NewValueList)
Ifstr(i) $(DoOsiCBEna) != "Yes"
Set NewValueList = {{Interrupt, $(NoTitle), $(!REG_VT_DWORD), $(COMInterruptNumber)},+ ; Interrupt for JOS modem/network
{PortAddress, $(NoTitle), $(!REG_VT_DWORD), $(COMIoBaseAddrValue)}} ; I/O Base address for JOS
Shell $(UtilityInf), AddValueList, $(MyNewSerialHandle), $(NewValueList)
Endif
CloseRegKey $(MyNewSerialHandle)
; JOSNT: add comm port info to HARDWARE\DEVICEMAP\SERIALCOMM section
OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP\SERIALCOMM" $(MAXIMUM_ALLOWED) MyNewSerialHandle
Ifstr $(MyNewSerialHandle) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP" $(MAXIMUM_ALLOWED) SerialKey
CreateRegKey $(SerialKey) {"SERIALCOMM",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyNewSerialHandle
CloseRegKey $(SerialKey)
Endif
SetRegValue $(MyNewSerialHandle) {"SerialOsitechJOS",$(NoTitle),$(!REG_VT_SZ),$(ComPortValue)}
CloseRegKey $(MyNewSerialHandle)
; JOSNT: add comm port info to SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports section
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports" $(MAXIMUM_ALLOWED) MyNewSerialHandle
Ifstr $(MyNewSerialHandle) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(MAXIMUM_ALLOWED) SerialKey
CreateRegKey $(SerialKey) {"Ports",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyNewSerialHandle
CloseRegKey $(SerialKey)
Endif
SetRegValue $(MyNewSerialHandle) {$(ComPortValue)":",$(NoTitle),$(!REG_VT_SZ),"9600,n,8,1"}
CloseRegKey $(MyNewSerialHandle)
Else
;
; Remove the COM port
;
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) MyNewSerialHandle
DeleteRegTree $(MyNewSerialHandle) "SerialOsitechJOS"
CloseRegKey $(MyNewSerialHandle)
OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP\SERIALCOMM" $(MAXIMUM_ALLOWED) MyNewSerialHandle
DeleteRegValue $(MyNewSerialHandle) "SerialOsitechJOS"
CloseRegKey $(MyNewSerialHandle)
Endif
Endif
; --- -fwb-
; +++ -drd-
OpenRegKey $(!REG_H_LOCAL) "" $(CardWizKeyName) $(MAXIMUM_ALLOWED) CardWizKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardExecKeyName) $(MAXIMUM_ALLOWED) CardExecKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardWareKeyName) $(MAXIMUM_ALLOWED) CardWareKey
Set DoOsiCBEna = "Yes"
Ifstr $(CardWizKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardWizKey)
Endif
Ifstr $(CardExecKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardExecKey)
DeleteRegValue $(HardParameterKey) "Pcmcia"
Ifstr $(OldAdapterName) == ""
set OldAdapterName = $(ProductHardwareName)$(AdapterNumber)
Endif
Set NewValueList = {{SoftexPcmcia,$(NoTitle),$(!REG_VT_DWORD),1},+
{AdapterName,$(NoTitle),$(!REG_VT_SZ),$(OldAdapterName)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
Endif
Ifstr $(CardWareKey) != $(KeyNull)
Set DoOsiCBEna = "No"
CloseRegKey $(CardWareKey)
Endif
Ifstr(i) $(DoOsiCBEna) == "Yes"
;
; CardWizard is not installed, well need to use Ositech enabler
;
; Create the OsiCBEna service
;
Debug-Output "otcinf- Add OSICBENA.SYS service"
Shell $(UtilityInf), CreateService,+
"osicbena",+
"OsiCBEna CardBus Enabler",+
"\SystemRoot\System32\drivers\osicbena.sys",+
"kernelauto",+
"System Bus Extender",+
{},+
""
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "otcinf- ShellCode error from CreateService"
goto ShellCodeError
endif
;
; Set the Start to 'Manual' from 'System', since kernelauto only sets Start to 1
;
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\osicbena" $(MAXIMUM_ALLOWED) MyOsicbenaHandle
Ifstr $(MyOsicbenaHandle) == $(KeyNull)
Debug-Output "otcinf- FAILURE to open osicbena key after creation!"
else
Set NewValueList = {{Start, $(NoTitle), $(!REG_VT_DWORD), 3}} ; "Start=0x00000003"
Shell $(UtilityInf), AddValueList, $(MyOsicbenaHandle), $(NewValueList)
CloseRegKey $(MyOsicbenaHandle)
Endif
else
;
; Set the Start to 'Disabled' since Card and Socket Services
;
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\osicbena" $(MAXIMUM_ALLOWED) MyOsicbenaHandle
Ifstr $(MyOsicbenaHandle) == $(KeyNull)
Debug-Output "otcinf- FAILURE to open osicbena key after creation!"
else
Set NewValueList = {{Start, $(NoTitle), $(!REG_VT_DWORD), 4}} ; "Start=0x00000004"
Shell $(UtilityInf), AddValueList, $(MyOsicbenaHandle), $(NewValueList)
CloseRegKey $(MyOsicbenaHandle)
Endif
endif
;
; Try to start the service to update the parameters.
;
; Can not do this yet, when config is ready this may be done through it.
;
; Add the PCMCIA DataBase Entries for the JoS and 7oS
;
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia" $(MAXIMUM_ALLOWED) PcmciaKey
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase" $(MAXIMUM_ALLOWED) PcmciaDBKey
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase\Ositech" $(MAXIMUM_ALLOWED) OsitechKey
Ifstr $(PcmciaKey) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services" $(MAXIMUM_ALLOWED) ServicesKey
CreateRegKey $(ServicesKey) {"Pcmcia",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" PcmciaKey
Endif
CloseRegKey $(ServicesKey)
Ifstr $(PcmciaDBKey) == $(KeyNull)
CreateRegKey $(PcmciaKey) {"DataBase",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" PcmciaDBKey
Endif
CloseRegKey $(PcmciaKey)
Ifstr $(OsitechKey) == $(KeyNull)
CreateRegKey $(PcmciaDBKey) {"Ositech",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" OsitechKey
Endif
CloseRegKey $(PcmciaDBKey)
;
; The ...\Pcmcia\DataBase\Ositech Key is created and Open in OsitechKey
;
; Create the JoS Ethernet Device Key and add values, if it already exists do nothing
CreateRegKey $(OsitechKey) {$(KeyJoSEth),0,GenericClass} "" $(MAXIMUM_ALLOWED) "" CBDevKey
Ifstr $(CBDevKey) != $(KeyNull)
Set DevValueList = {{DeviceType, $(NoTitle), $(!REG_VT_SZ), "NET"},+
{Driver,$(NoTitle), $(!REG_VT_SZ), $(ProductSoftwareName)}}
Shell $(UtilityInf), AddValueList, $(CBDevKey), $(DevValueList)
CloseRegKey $(CBDevKey)
Endif
; Create the JoS Modem Device Key and add values, if it already exists do nothing
CreateRegKey $(OsitechKey) {$(KeyJoSMdm),0,GenericClass} "" $(MAXIMUM_ALLOWED) "" CBDevKey
Ifstr $(CBDevKey) != $(KeyNull)
Set DevValueList = {{DeviceType, $(NoTitle), $(!REG_VT_SZ), "MODEM"},+
{Driver,$(NoTitle), $(!REG_VT_SZ), "Serial"}, +
{ParamSubKey,$(NoTitle), $(!REG_VT_SZ), "SerialOsitechJoS"}}
Shell $(UtilityInf), AddValueList, $(CBDevKey), $(DevValueList)
CloseRegKey $(CBDevKey)
Endif
; Create the 7oS Ethernet Device Key and add values, if it already exists do nothing
CreateRegKey $(OsitechKey) {$(Key7oSEth),0,GenericClass} "" $(MAXIMUM_ALLOWED) "" CBDevKey
Ifstr $(CBDevKey) != $(KeyNull)
Set DevValueList = {{DeviceType, $(NoTitle), $(!REG_VT_SZ), "NET"},+
{Driver,$(NoTitle), $(!REG_VT_SZ), $(ProductSoftwareName)}}
Shell $(UtilityInf), AddValueList, $(CBDevKey), $(DevValueList)
CloseRegKey $(CBDevKey)
Endif
; To get the point enablers to work properly ...
; Create the JoS Ethernet Device Key
CreateRegKey $(OsitechKey) {$(KeyPointJoS),0,GenericClass} "" $(MAXIMUM_ALLOWED) "" CBDevKey
Ifstr $(CBDevKey) != $(KeyNull)
Set DevValueList = {{DeviceType, $(NoTitle), $(!REG_VT_SZ), "NET"},+
{Driver,$(NoTitle), $(!REG_VT_SZ), $(ProductSoftwareName)},+
{InfFileName,$(NoTitle),$(!REG_VT_SZ), $(CONTEXTINFNAME)},+
{Option,$(NoTitle),$(!REG_VT_SZ), "OTCCB62"}}
Shell $(UtilityInf), AddValueList, $(CBDevKey), $(DevValueList)
CloseRegKey $(CBDevKey)
Endif
;+++
; CardWizard 4.10
CreateRegKey $(OsitechKey) {$(KeyPointJoS)"\0",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" CBDevKey
Ifstr $(CBDevKey) != $(KeyNull)
Set DevValueList = {{DeviceType, $(NoTitle), $(!REG_VT_SZ), "NET"},+
{Driver,$(NoTitle), $(!REG_VT_SZ), $(ProductSoftwareName)},+
{InfFileName,$(NoTitle),$(!REG_VT_SZ), $(CONTEXTINFNAME)},+
{Option,$(NoTitle),$(!REG_VT_SZ), "OTCCB62"}}
Shell $(UtilityInf), AddValueList, $(CBDevKey), $(DevValueList)
CloseRegKey $(CBDevKey)
Endif
CreateRegKey $(OsitechKey) {$(KeyPointJoS)"\1",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" CBDevKey
Ifstr $(CBDevKey) != $(KeyNull)
Set DevValueList = {{DeviceType, $(NoTitle), $(!REG_VT_SZ), "MODEM"},+
{Driver,$(NoTitle), $(!REG_VT_SZ), "Serial"},+
{ParamSubKey,$(NoTitle), $(!REG_VT_SZ), "SerialOsitechJoS"}}
Shell $(UtilityInf), AddValueList, $(CBDevKey), $(DevValueList)
CloseRegKey $(CBDevKey)
Endif
;---
; CardWizard 4.10.xx
; Create the 7oS Ethernet Device Key
CreateRegKey $(OsitechKey) {$(KeyPoint7oS),0,GenericClass} "" $(MAXIMUM_ALLOWED) "" CBDevKey
Ifstr $(CBDevKey) != $(KeyNull)
Set DevValueList = {{DeviceType, $(NoTitle), $(!REG_VT_SZ), "NET"},+
{Driver,$(NoTitle), $(!REG_VT_SZ), $(ProductSoftwareName)},+
{InfFileName,$(NoTitle),$(!REG_VT_SZ), $(CONTEXTINFNAME)},+
{Option,$(NoTitle),$(!REG_VT_SZ), "OTCCB61"}}
Shell $(UtilityInf), AddValueList, $(CBDevKey), $(DevValueList)
CloseRegKey $(CBDevKey)
Endif
CloseRegKey $(OsitechKey)
; --- -drd-
Ifstr(i) $(DoOsiCBEna) != "Yes"
set NewValueList = {{LineSpeed,$(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
Endif
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(HardNetCardKey)
CloseRegKey $(HardNetRuleKey)
set NewValueList = {{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNum)},+
{SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(DeviceNum)},+
{FunctionNumber,$(NoTitle),$(!REG_VT_DWORD),$(FunctionNum)}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
;+++
; Sept 12 1998
;
Ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
Shell $(UtilityInf),AddDefaultNetCardParameters,$(HardParameterKey)
Endif
;
; Sept 12 1998
;---
CloseRegKey $(HardParameterKey)
; endif
;
; EndForListDo
EndWait
goto successful
updateparameters =+
Debug-Output "otcinf- updateparameter-"
OpenRegKey $(!REG_H_LOCAL) "" $(CardWizKeyName) $(MAXIMUM_ALLOWED) CardWizKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardExecKeyName) $(MAXIMUM_ALLOWED) CardExecKey
OpenRegKey $(!REG_H_LOCAL) "" $(CardWareKeyName) $(MAXIMUM_ALLOWED) CardWareKey
Set DoOsiCBEna = "Yes"
Ifstr $(CardWizKey) != $(KeyNull)
set NewValueList = {{Pcmcia,$(NoTitle),$(!REG_VT_DWORD),1}}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
Set DoOsiCBEna = "No"
CloseRegKey $(CardWizKey)
Endif
;
; For Softex we will request that Card and Socket Services provide resources
; so we use "0" for IRQ and I/O address.
;
Ifstr $(CardExecKey) != $(KeyNull)
set NewValueList = {{SoftexPcmcia,$(NoTitle),$(!REG_VT_DWORD),1},+
{IoBaseAddress,$(NoTitle),$(!REG_VT_DWORD),0},+
{IoLength,$(NoTitle),$(!REG_VT_DWORD),256},+
{InterruptNumber,$(NoTitle),$(!REG_VT_DWORD),0}}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
DeleteRegValue $(KeyParameters) "Pcmcia"
Set DoOsiCBEna = "No"
CloseRegKey $(CardExecKey)
Endif
Ifstr $(CardWareKey) != $(KeyNull)
set NewValueList = {{Pcmcia,$(NoTitle),$(!REG_VT_DWORD),1}}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
Set DoOsiCBEna = "No"
CloseRegKey $(CardWareKey)
Endif
ifstr(i) $(DoOsiCBEna) == "Yes"
set NewValueList = {{Pcmcia,$(NoTitle),$(!REG_VT_DWORD),1}}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
endif
set HardParameterKey = $($R3)
set BusTypeNum = 5
set NewValueList = {{AdapterType,$(NoTitle),$(!REG_VT_DWORD),$(Adapter$(Option)Type)},+
{MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
{BurstLength,$(NoTitle),$(!REG_VT_DWORD),$(BurstLength)},+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
{ProductId,$(NoTitle),$(!REG_VT_DWORD),$($(Option)CFID)},+
{SystemId,$(NoTitle),$(!REG_VT_DWORD),$($(Option)SYSID)},+
{MaxTransmits,$(NoTitle),$(!REG_VT_DWORD),8},+
{MaxReceives,$(NoTitle),$(!REG_VT_DWORD),64},+
{ExtraReceives,$(NoTitle),$(!REG_VT_DWORD),64},+
; {IpgDelay,$(NoTitle),$(!REG_VT_DWORD),3},+
{BurstLength,$(NoTitle),$(!REG_VT_DWORD),0},+
{EarlyTXOff,$(NoTitle),$(!REG_VT_DWORD),1},+
{EarlyRXOff,$(NoTitle),$(!REG_VT_DWORD),0},+
{ReadMultiple,$(NoTitle),$(!REG_VT_DWORD),1},+
; {PciLatencyTimer,$(NoTitle),$(!REG_VT_DWORD),64},+
; {InterruptMitigation,$(NoTitle),$(!REG_VT_DWORD),0},+
{TransmitThreshold10,$(NoTitle),$(!REG_VT_DWORD),64},+
{TransmitThreshold100,$(NoTitle),$(!REG_VT_DWORD),256},+
{ReceiveThreshold,$(NoTitle),$(!REG_VT_DWORD),128},+
; {Pcmcia,$(NoTitle),$(!REG_VT_DWORD),1},+
{ScrambleOn,$(NoTitle),$(!REG_VT_DWORD),0}}
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
Ifstr(i) $(DoOsiCBEna) != "Yes"
set NewValueList = {{LineSpeed,$(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)}}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
Endif
;+++
; Sept 12 1998
;
Ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
Shell $(UtilityInf),AddDefaultNetCardParameters,$(HardParameterKey)
Endif
;
; Sept 12 1998
;---
CloseRegKey $(KeyParameters)
goto successful
bindingadapter =+
Debug-Output "otcinf- bindingadapter-"
set Error = "Binding: Sorry, not yet implemented."
goto fatal
removeadapter = +
Debug-Output "otcinf- removeadapter-"
Set TrayKeyName = $(!NTN_SoftwareBase)"\Microsoft\Windows\CurrentVersion\Run"
OpenRegKey $(!REG_H_LOCAL) "" $(TrayKeyName) $(MAXIMUM_ALLOWED) TrayKey
Ifstr $(TrayKey) != $(KeyNull)
DeleteRegValue $(TrayKey) "OSIGUIEXE"
CloseRegKey $(TrayKey)
Endif
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
else
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $(!NTN_RegBase)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
UpgradeSoftware = +
Debug-Output "otcinf- UpgradeSoftware-"
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
Endif
set !UG_Filename = $($R0)
install "Install-Update"
Ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
goto fatal
Endif
SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
CloseRegKey $(KeyProduct)
Else
goto fatalregistry
Endif
goto end
successful = +
Debug-Output "otcinf- successful-"
goto end
abandon = +
Debug-Output "otcinf- abandon-"
ForListDo $(OEM_ABANDON_OPTIONS)
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $($)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
EndForListDo
Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), FALSE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
warning = +
Debug-Output "otcinf- warning-"
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(to)
else-ifstr(i) $($R1) == "CANCEL"
goto $(from)
else
goto "end"
endif
nonfatalinfo = +
Debug-Output "otcinf- nonfatalinfo-"
Set CommonStatus = STATUS_USERCANCEL
Set Severity = STATUS
goto nonfatalmsg
nonfatal = +
Debug-Output "otcinf- nonfatal-"
Set Severity = NONFATAL
goto nonfatalmsg
nonfatalmsg = +
Debug-Output "otcinf- nonfatalmsg-"
ifstr(i) $(Error) == ""
Set Severity = NONFATAL
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(from)
else
goto "end"
endif
fatalregistry = +
Debug-Output "otcinf- fatalregistry-"
Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
fatal = +
Debug-Output "otcinf- fatal-"
ifstr(i) $(Error) == ""
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto setfailed
ShellCodeError = +
Debug-Output "otcinf- ShellCodeError-"
set DlgType = "MessageBox"
set STF_MB_TITLE = $(ShellCodeErrorTitle)
set STF_MB_TEXT = $(ShellCodeErrorText)
set STF_MB_TYPE = 1
set STF_MB_ICON = 3
set STF_MB_DEF = 1
ui start "Error Message"
goto setfailed
setfailed = +
Debug-Output "otcinf- setfailed-"
set CommonStatus = STATUS_FAILED
ifstr(i) $(OEM_ABANDON_ON) == TRUE
set OEM_ABANDON_ON = FALSE
goto abandon
endif
goto end
end = +
Debug-Output "otcinf- end-"
goto term
term = +
Debug-Output "otcinf- term-"
Return $(CommonStatus)
[Install-Option]
Debug-Output "otcinf- [Install-Option]-"
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
Ifcontains(i) $(Option) in {"OTCCB62"}
AddSectionFilesToCopyList Files-Modem $(SrcDir) $(!STF_WINDOWSPATH)\inf
endif
; AddSectionFilesToCopyList Files-Enabler $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
; AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH)
endif
ifstr(i) $(DoCopy) == "YES"
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
endif
Exit
[Install-Hlp]
Debug-Output "otcinf- [Install-Hlp]-"
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
ifstr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-Enabler $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
endif
; ifstr(i) $(DoCopy) == "YES"
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
; endif
Exit
[Install-Update]
Debug-Output "otcinf- [Install-Update]-"
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
AddSectionFilesToCopyList Files-Enabler $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
Ifcontains(i) $(Option) in {"OTCCB62"}
AddSectionFilesToCopyList Files-Modem $(SrcDir) $(!STF_WINDOWSPATH)\inf
Endif
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Install-Softex]
Debug-Output "otcinf- [Install-Softex]-"
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
AddSectionFilesToCopyList Files-Softex $(SrcDir) $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-Softex$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
Ifcontains(i) $(Option) in {"OTCCB62"}
AddSectionFilesToCopyList Files-Modem $(SrcDir) $(!STF_WINDOWSPATH)\inf
Endif
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Source Media Descriptions]
1 = "Ositech SuperDisk"
[ProductType]
Debug-Output "otcinf- [ProductType]-"
STF_PRODUCT = Winnt
STF_PLATFORM = I386
[Files-Inf]
1, OEMSETNT.INF, SIZE=10000, RENAME=OEMNADOT.INF ; RENAME=$(!UG_Filename)
[Files-Modem]
1, MDMOSICB.INF, SIZE=10000, BACKUP=*
[Files-OTCCB61]
1, OTC06X4.SYS, SIZE=29999, RENAME=OTCETHCB.SYS
[Files-OTCCB62]
1, OTC06X4.SYS, SIZE=29999, RENAME=OTCETHCB.SYS
1, SERIAL.SYS, SIZE=29999, BACKUP=*
[Files-Enabler]
1, OSICBENA.SYS, SIZE=44999
[Files-Hlp]
1, OTCETHCB.HLP, SIZE=19999
1, OTCCBCFG.EXE, SIZE=29999
[Files-SoftexOTCCB61]
1, OTC06X4S.SYS, SIZE=29999, RENAME=OTCETHCB.SYS
[Files-SoftexOTCCB62]
1, OTC06X4S.SYS, SIZE=29999, RENAME=OTCETHCB.SYS
[Files-Softex]
1, OSIGUI.EXE, SIZE=54999
[LanguagesSupported]
ENG
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.