ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Compex USB 10/100Base-TX Fast Ethernet Adapter º º CopyRight(c) 2000 Compex Inc. º º All rights reserved º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ----------------- BEFORE YOU BEGIN ----------------- Your computer must meet the following requirements to be compatible with Compex USB 10/100Base-TX Fast Ethernet Adapter: 1. In order to use this device, you must have a copy of Microsoft Windows 98 operating system installed on your PC. Some versions of Windows 95 version B (OSR2) support USB port. This Windows version and UBS support may not work properly with this driver. It is designed specifically and tested for Windows 98 only. 2. Also, the device requires that a USB port is installed and enabled on your PC. Some PCs have a USB port, but it is disabled. Usually there is a toggle switch on the motherboard that will enable a PC's USB port. Consult your computer's user guide. Some motherboards have USB interfaces, but no ports. You should be able to install your own USB port and attach it to your PC's motherboard using hardware purchased at any computer store. Please refer to A:\README.TXT if you have not read it. ---------------------------------------------------------------------------- DRIVER INSTALLATION ---------------------------------------------------------------------------- Follow the instructions below to install the adapter's driver. 1. Install the Compex USB 10/100Base-TX Fast Ethernet Adapter to your PC or notebook or USB hub if you haven't already done so. (See A:\README.TXT in Hardware setup) 2. Turn ON your PC or notebook and boot up Windows 98. 3. Windows 98 will display, "USB 10/100 Adapter" in "New Hardware Found" dialog box and "Add New Hardware Wizard" dialog box. If the Wizard does not appear, please refer the section "Is USB port device correctly installed" below. 4. Click "Next >" button when "Search for the best for your device. [Recommended]" is on. 5. Insert the USB Adapter Driver Diskette in your floppy drive. 6. Enable the "Floppy disk drives" check box and then click "Next >" button. 7. Windows 98 will display, "Compex USB 10/100Base-TX Fast Ethernet Adapter" in "Add New Hardware Wizard" dialog box. 8. Click "Next >" button and Windows starts to copy files from Windows 98 CD-ROM to your hard disk. 9. When the Insert Disk message appears, click OK. When the Copying Files ... window appears, type A:\ into the box displayed and click OK. 10. Click "Finish" button from "Add New Hardware Wizard" dialog box. 11. Remove the USB Adapter Driver Diskette from your floppy drive. 12. Restart your computer to take effect the network function. Uninstalling Compex USB 10/100Base-TX Faet Ethernet Adapter Driver ------------------------------------------------------------------ 1. Close all active windows. 2. Click Settings, click on Setting then Control Panel. Double-click on the select Network icon. 3. Under the configuration tab highlight, "Compex USB 10/100Base-TX Fast Ethernet Adapter" Click Remove then select OK. 4. If you are prompted to restart your computer click NO. 5. Start the Windows Explorer and go to Windows\System folder. 6. Delete the file AN986N.SYS. 7. Go to Windows\Inf folder. Delete the file AN986.inf. Go to Windows\Inf\Other folder. Delete the file CompexAN986N.inf. 8. Shut down the computer completely. Driver is removed from the computer. Is USB port device correctly installed ? ---------------------------------------- If the Wizard does not appear when you plug in the adapter, go to "Device Manager" to check whether "Universal Serial Bus controllers" exists. You can do this to go to "Device Manager" : Right click on the "My Computer" icon on your desktop, then select "Properties" or Double click on the "System" icon in Control Panel. Select the "Device Manager" tab. Select and expand "Universal Serial Bus controllers". For example, you will see Universal Serial Bus controllers Intel 82371AB/EB PCI to USB Universal Host Controller USB Root Hub Make sure that there is no red "X" sign or "!" mark on them. Thus, USB is correctly installed.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.