----------------------------------------------- SiS 900/7016 PCI Fast Ethernet Adapter Installation Remote boot to Windows NT Server ----------------------------------------------- Install the NT server 3.5, 3.51, 4.0 RPL server: ------------------------------------------------ 1. Install the Remoteboot Service on the NT Server. 1.1 Choose Control Panel, Network, Add Software, Remoteboot Service, put NT server CD into CD-ROM drive, to install Remoteboot Service. [Note] To install RPL server, you must install DLC and NetBEUI protocols in your NT server first. 2. Install MS-DOS Files for Remoteboot workstation. Copy all the MS-DOS 6.22 files to ----> \\systemroot\RPL\RPLFILES\BINFILES\DOS622 copy c:\dos\*.* \\systemroot\RPL\RPLFILES\BINFILES\DOS622 attrib -s -h c:\io.sys attrib -s -h c:\msdos.sys copy c:\io.sys \\systemroot\RPL\RPLFILES\BINFILES\DOS622 copy c:\msdos.sys \\systemroot\RPL\RPLFILES\BINFILES\DOS622 attrib +s +h c:\io.sys attrib +s +h c:\msdos.sys 3. Create Remoteboot configuration for new adapter 3.1 Copy the MS-DOS device driver(NDIS2) for the Ethernet adapter to the \\systemroot\RPL\BBLOCK\NDIS directory. for example: SIS900.DOS NDIS2 driver for the PCI adapter. copy Bootrom\NDIS2drv\*.* \\systemroot\RPL\BBLOCK\NDIS 3.2 Create the directory \\systemroot\RPL\BBLOCK\NETBEUI\SIS900. Copy DOSBB.CNF, PROTOCOL.INI files from directory \\systemroot\RPL\BBLOCK\NETBEUI\NE2000. Modify DOSBB.CNF and PROTOCOL.INI. The templates for DOSBB.CNF and PROTOCOL.INI are stored at the \BOOTROM directory in this driver diskette. Sample for DOSBB.CNF: ; DOS on SiS900 PCI Fast Ethernet BASE D0H RPL BBLOCK\RPLBOOT.SYS LDR BBLOCK\RPLSTART.COM ~ DAT BBLOCK\NETBEUI\SIS900\PROTOCOL.INI DRV BBLOCK\RPLDISK.SYS ~ ~ ~ EXE BBLOCK\RPLPRO1.COM ~ 2 ~ EXE BBLOCK\I13.COM ~ ~ ~ EXE BBLOCK\RPLBIND2.EXE ~ ~ EXE BBLOCK\PROTMAN.EXE ~ ~ EXE BBLOCK\RPLBIND1.EXE ~ ~ ;DRV BBLOCK\IPXNDIS.DOS ~ ~ ~ ;DRV BBLOCK\TCPDRV.DOS /I:C:\LANMAN.DOS ~ ~ EXE BBLOCK\NETBEUI\NETBEUI.EXE ~ 10 ~ DRV BBLOCK\NDIS\SIS900.DOS ~ ~ ~ DRV BBLOCK\PROTMAN.DOS /I:C:\LANMAN.DOS ~ M Sample for PROTOCOL.INI: [protman] drivername = protman$ dynamic = yes priority = netbeui [netbeui_xif] drivername = netbeui$ bindings = sis900_nif names = 6 ncbs = 12 packets = 20 pipeline = 10 sessions = 6 stacksize = 512 lanabase = 0 [xnsnb_xif] drivername = xnsnb$ bindings = SIS900_nif load = xnsnb[cbr] lanabase = 1 [xnstp_xif] drivername = xnstp$ bindings = sis900_nif load = xnstp[ub] lanabase = 1 [tcpip_xif] drivername = TCPIP$ disabledhcp = (TCPIP_NO_DHCP) ipaddress0 = (TCPIP_ADDRESS) subnetmask0 = (TCPIP_SUBMASK) defaultgateway0 = (TCPIP_GATEWAY) tcpsegmentsize = 1450 tcpwindowsize = 1450 nbsessions = 6 load = tcptsr[c],tinyrfc[c],emsbfr[cr] unload = "unloadt /notsr[dc]" bindings = sis900_nif lanabase = 1 [ipx_xif] drivername = ipx$ load = ipxmark[u],ipx[u] unload = ipxrel[c] bindings = sis900_nif lanabase = 1 [msdlc_xif] drivername = msdlc$ bindings = sis900_nif load = msdlc[ub] unload = msdlc[u] [sis900_nif] drivername = SIS900$ 3.3 Use RPLCMD utility to add a bblock record for new adapter. Under MS-DOS Prompt, type <1>. NET START RemoteBoot <2>. RPLCMD 3.4 You should follow the direction displayed on the screen. ;;; Add a new boot Block: Adapter Boot Config Profile Service Vendor Wksta [Quite] B Add Del Enum:A BootName=DOSX ; VendorName=00E006 ;for SiS900 VendorName=002642 ;for SiS630E BbcFile=BBLOCK\NETBEUI\SIS900\DOSBB.CNF ; BootCommet=DOS SiS900 Fast Ethernet ;SiS900 BootComment=DOS SiS630E Onboard Lan ;SiS630E WindowsSize=0 ;;; Add a new config: Adapter Boot Config Profile Service Vendor Wksta [Quite] C Add Del Enum:A ; ConfigName=DOS622X ;SiS900 ConfigName=DOS622XX ;SiS630E BootName=DOSX DirName=DOS DirName2=DOS622 FitShared=FITS\DOS622.FIT FitPersonal=FITS\DOS622P.FIT ; ConfigComment=DOS 6.22 SiS900 Fast Ethernet ;SiS900 ConfigComment=DOS SiS630E Onboard Lan ;SiS630E DirName3= DirName4= ;;; Add new vendor ID: Adapter Boot Config Profile Service Vendor Wksta [Quite] V Add Del Enum: A ; VendorName=00E006 ;SiS900 VendorName=002642 ;SiS630E ; VendorComment=SiS900 Fast Ethernet ;SiS900 VendorComment=SiS630E Onboard Lan ;SiS630E [Note] VendorName is OUI Number -- the first six digit of the MAC address on your card. e.g. 1)SiS900: MAC address is 00E006000001 VendorName is 00E006 2)SiS630E:MAC address is 002642060008 VendorName is 002642 3.5 Shutdown Windows NT server, and reboot it. 4. Login to NT server as Administrator. 5. Install BootROM on remote client and power on remote client. 6. Start RemoteBoot service and Remoteboot manager. 6.1 Under MS-DOS Prompt, type "NET START Remoteboot" 6.2 In Network administrator, Remoteboot Manager 1.Choose Remoteboot, New Profile, to create an SiS900 Profile Name or SiS630E Profile Name. 2.Add new workstation for this Ethernet adapter and choose SiS900 or SiS630E Profile file. [Note] If the Node ID of workstation does not match with your Profile file, you can use "Convert Adapters" in Remoteboot menu of Remoteboot Manager to configure or cteate the Profile file.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.