Retech8139D Fast Ethernet 10/100 Adapter
Novell ODI Server Driver
Contents:
---------
1. File Description
2. Driver Installation for NetWare Server
3. Parameters Description
1. File Description
-------------------
Filename Description
================= =====================================================
README.TXT Presents a summary of the contents for NetWare Server
driver installation.
IP100.LAN IP100 based 32-bit ODI Driver
This driver complies with NetWare ODI Server driver
SPEC 3.31.
IP100.LDI The IP100 driver installation file for Netware 6.x/
Netware 5.x/Netware 4.x.
4.X\NBI.NLM NetWare Server 4.X Bus Interface module.
4.X\MSM.NLM NetWare Server 4.X LAN driver Media Support
Module (MSM).
4.X\ETHERTSM.NLM NetWare Server 4.X LAN driver Topology Specific Module
(TSM) for Ethernet.
2. Driver Installation for NetWare Server
-----------------------------------------
** Driver Installation for NetWare Server 4.X **
a. Update Netware Server to 4.2 .
(If dont update to 4.2, use diskette update file "MSM.NLM,
ETHERTSM.NLM")
b. Run NetWare Server System .
c. When the Server prompt appears, load the NetWare Server
Installation Utility ==> "LOAD INSTALL"
d. Select "Driver options" from the "Installtion Options" menu.
e. Select "Configure network drivers" from the "Driver Options" menu.
f. Select "Select a driver" from the "Additional Driver Actions" menu
g. Press <Ins> to install a unlisted driver, then press <F3> to
specify a different path.
h. Insert Driver Diskette in your PC's floppy drive and specify
the path A:\NETWARE\SERVER.
i. Select "Retech8139D Fast Ethernet 10/100 Driver" from
the "Select a driver to install:" menu.
j. If necessary, select "Select/Modify driver parameters and
protocols" from the "Board IP100_1 (Driver IP100) Actions" memu.
k. Follow instructions to complete driver installation.
** Driver Installation for NetWare Server 5.X/6.X **
a. Run NetWare Server System .
b. When the Server prompt appears, load the NetWare Server
Installation Utility ==> "LOAD NWCONFIG"
c. Select "Driver options" from the "Installtion Options" menu.
d. Select "Configure network drivers" from the "Driver Options" menu.
e. Select "Select a driver" from the "Additional Driver Actions" menu
f. Press <Ins> to install a unlisted driver, then press <F3> to
specify a different path.
g. Insert Driver Diskette in your PC's floppy drive and specify
the path A:\NETWARE\SERVER.
h. Select "Retech8139D Fast Ethernet 10/100 Driver" from the
"Select a driver to install:" menu.
i. If necessary, select "Select/Modify driver parameters and
protocols" from the "Board IP100_1 (Driver IP100) Actions" memu.
j. Follow instructions to complete driver installation.
Sample AUTOEXEC.NCF for NetWare Server
AUTOEXEC.NCF (one board)
========================
LOAD IP100 SLOT=2 FRAME=ETHERNET_802.2 NAME=IP100_8022
BIND IPX IP100_8022 NET=10
LOAD IP100 SLOT=2 FRAME=ETHERNET_802.3 NAME=IP100_8023
BIND IPX IP100_8023 NET=20
LOAD IP100 SLOT=2 FRAME=ETHERNET_II NAME=IP100_II
BIND IPX IP100_II NET=30
LOAD IP100 SLOT=2 FRAME=ETHERNET_SNAP NAME=IP100_SNAP
BIND IPX IP100_SNAP NET=40
3. Parameter Description
------------------------
The following parameters are used in IP100.LAN.
a. SLOT : Specifies which adapter is enabled when multiple IP100 based
adapters are found in your computer.
Ex: LOAD IP100 SLOT=3 FRAME=ETHERNET_802.2
LOAD IP100 SLOT=4 FRAME=ETHERNET_II
b. FRAME : Specifies which frame type is used by the driver. Accepted
values are Ethernet_802.2, Ethernet_802.3, Ethernet_II and
Ethernet_SNAP.
Ex: LOAD IP100 FRAME=ETHERNET_802.2
LOAD IP100 FRAME=ETHERNET_802.3
LOAD IP100 FRAME=ETHERNET_II
LOAD IP100 FRAME=ETHERNET_SNAP
c. NODE : Use a different address to replace the node address burned
in EEPROM.
Ex: LOAD IP100 NODE=004095888888
4. SPEED : Specifies which medium type is used by the driver.
Accepted vaules are AUTOSENSE, 10BASET_NWAY, 10BASETFD_NWAY,
100BASETX_NWAY, 100BASETXFD_NWAY.
Ex: LOAD IP100 AUTOSENSE
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.