10/100 Fast Ethernet PCI Adapter
User's Manual
Thank you for purchasing our product!
This guide contains information to install and configure the 10/100 Fast
Ethernet PCI Adapter for proper operation. The 10/100 Fast Ethernet PCI
Adapter is a 32-bit 10/100 Mbps Ethernet network interface card for PCI
local bus-compliant PCs. It supports bus mastering architecture and
auto-negotiation which make it possible to use one common RJ-45 port and
standard twisted-pair cabling for both 10 Mbps and 100 Mbps connection.
Extensive driver support for commonly used network operating systems is
also provided.
Package Contents
Carefully unpack the contents of the package and verify them against the
checklist below.
10/100 Fast Ethernet PCI Adapter
10/100 Fast Ethernet PCI Adapter
Driver Diskette (included User's Manual)
Please inform your dealer immediately should there be any incorrect, missing
or damaged parts.
If possible, retain the carton, including the original packing materials.
Use them again to repack the product in case there is a need to return it
for repair.
Back up your Driver Diskette and use the copy as the working diskette. Do
this to protect the original from accidental damage.
Hardware Description
The 10/100 Fast Ethernet PCI Adapter has a RJ-45 connector and two LED
indicators.
LED Indicators
The adapter provides LED indicators for monitoring network conditions.
This section describes the function of each LED.
100BASE-TX Status Indicator (100)
Color : Green
Function : Network connection indicator for 100 Mbps port
This LED is used with 100BASE-TX only.
It lights up to indicate that the port is operating at 100 Mbps.
10BASE-T Status LED Indicator (10)
Color : Green
Function : Network connection indicator for 10Mbps port
This LED is used with 10Base-T only.
If lights up to indicate that the port is operating at 10Mbps.
Summary of LED Display
During normal network operation, the adapter's LEDs display the
following indications:
Table 1.1 Summary of LED Indicators
Media Type 10(Green) 100(Green)
100BASE-TX off on
10BASE-T on off
Hardware Installation
1. Power off the PCI Local bus PC and remove its cover.
Please refer to your computer's Installation Manual for instructions on
how to remove the cover.
2. Select an available slot and plug in the adapter.
The adapter provides a 32-bit bus interface.
It plugs into any available PCI bus slot that supports Bus Master mode.
Remove the bracket on the slot you've selected, then insert the adapter
into the slot. Carefully push the adapter into the slot until all the edge
connectors are firmly in place. Screw the adapter's face plate onto the
opening in the back of the computer to secure the connection. Then replace
the PC's cover.
3. Connect your adapter to the network.
Connect the adapter to the network using twisted-pair cabling with an
RJ-45 connector.
4. Power on the PC.
After hardware installation has been completed, power on the computer.
5. Change your computer's BIOS setup to enable Bus Master mode and select an
IRQ setting.
The setup procedure and the terminology used when referring to Bus Master
mode and IRQ parameters may vary with your computer's BIOS. Some BIOS have
Bus Master mode enabled for all the motherboard's PCI expansion slots,
while others provide the option to turn this feature on or off. Refer to
your computer's installation manual for more information. Please see the
following section on Adapter Configuration for related information.
6. Install the software driver.
For related topics see the section on Software Drivers later in this
chapter.
Adapter Configuration
The adapter is configured using the host PCI computer's BIOS setup program.
This is done by changing the computer's BIOS setting to enable bus master
mode, and then setting up the IRQ. The procedure to implement this and the
terminology used depend on the BIOS you are using.
Some BIOS have Bus Master mode enabled for all the motherboard's PCI
expansion slots; others provide the option of turning this feature on or off.
For example, if your computer uses the Phoenix BIOS, there is a "Device
Select" field where you should input the slot number of the PCI slot where
the adapter is installed, say "Slot 3 Device." Then for the fields that read
as "Enable Device" and "Enable Master" you should change the settings to
"Enabled." The same is true for the adapter's IRQ setting, which is mapped
to the BIOS IRQ setup of the host PCI computer.
Finally, you need to set the Trigger/Routing field to select the Trigger
method by which the IRQ is assigned or routed to the PCI slot. There are
three types of settings to choose from:
* Level/Auto - This is usually the default. Choosing this option leaves
the assigned IRQ free for other use if the installed card
does not use it.
* Level/Forced - If you are not able get the PCI card to work properly,
choose this option. This will assign the specified IRQ
permanently to the card.
* Edge/Auto - Some PCI boards support this option. Do not use it for
this card.
Note : The PCI adapters can only function with the EMM386.exe memory
manager program version 4.49 or later. You can verify its version
number by entering EMM386 at the DOS Prompt.
Do not specify the "highscan" option with the EMM386.exe statement
in your config.sys file or your system will hang.
If you run MEMMAKER and select Custom Setup, do not specify
"Aggressively scan upper memory", or it will automatically insert
the HIGHSCAN flag into the EMM386 command line. This parameter
cannot be manually removed once it's installed, doing so will
cause the extended memory manager to malfunction.
Specifications
System Configuration
Transmission Technique : Baseband
Topology : Star
Transmission Rate : 10 Mbps and 100 Mbps
(Auto-negotiation)
Full-Duplex Operation : 10 Mbps and 100 Mbps
Media Type Supported : Cat. 3, 4 and 5 UTP for 10BASE-T
Cat. 5 UTP for 100BASE-TX
Hub-to-Workstation Distance : 100m
Cable Connections : One RJ-45 (socket) for 100BASE-TX and 10BASE-T
Standards Conformance : IEEE 802.3 10BASE-T, and
IEEE 802.3u 100BASE-TX
End-User Devices Supported : PCI local bus-compliant PCs
Data Bus Width : 32-bit
Bus Access : Bus Master
I/O Address : Automatically determined by configuration space
Interrupt : INT A on PCI slot pin assignment, which is mapped to the BIOS IRQ setup
Operating Environment
Power Consumption : 100BASE-TX
+5V/360mA (maximum)
10BASE-T
+5V/350mA (maximum)
Temperature : 0C to 55C/32F to 131F
Humidity : 10% to 90% (Non-condensing)
Size : 123mm x 65mm
Hardware Certification
Certification : CE Mark
Emissions : FCC Class B, VCCI Class 2, CISPR22 Class B
Immunity : IEC 1000-4-2,3,4
Software Driver Support
NetWare ODI Drivers
Novell NetWare 3.12, 4.1, 4.11, NetWare LAN WorkPlace TCP/IP,
Novell LAN Analyzer for NetWare
Packet Drivers
FTP PC/TCP, NCSA TCP/IP
NDIS 2.0 Drivers
Microsoft LAN Manager V2.x, IBM LAN Server 4.0, IBM LAN Support,
DEC PATHWORKS V.50
NDIS 3.0 Drivers
Windows for Workgroups 3.11, Windows 95,
Windows NT 3.50,3.51,4.0
NDIS 5.0 Drivers
Windows 98, Windows 2000
The publisher assumes no responsibility for errors that may appear in this
document. Nor does it make any commitment to update the information it
contains.
All brand and product names mentioned are trademarks or registered trademarks
of their respective companies.
*This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)this device must accept any interference received,
including interference that may cause undesired operation.
This Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouranged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by
the party responsible for campliance could void your authority to operate
the equipment.
SAFETY INSTRUCTIONS
1. Please read these safety instructions carefully.
2. Please keep this User's Manual for later reference.
3. Please disconnect this equipment from AC outlet before cleaning.
Don't use liquid or sprayed detergent for cleaning.
Use moisture sheet or cloth for cleaning.
4. For pluggable equipment, the socket-outlet shall be installed near
the equipment and shall be easily accessible.
5. Please keep this equipment from humidity.
6. Lay this equipment on a reliable surface when install.A drop or fall
could cause injury.
7. The openings on the enclosure are for air convection hence protect
the equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source when connect the
equipment to the power outlet.
9. Place the power cord such a way that people can not step on it. Do
not place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not use for long time, disconnect the equipment
from mains to avoid being damaged by transient overvoltage.
12. Never pour any liquid into opening, this could cause fire or electrical shock.
13. Never open the equipment. For safety reason, the equipment should only
be opened by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by a
service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment has not work well or you can not get it work
according to user's manual.
e. The equipment has dropped and damaged.
f. If the equipment has obvious sign of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT
UNCONDITIONED: STORAGE TEMPERATURE ABOVE60(140),IT
MAY DAMAGE THE EQUIPMENT.
16. The sound pressure level at the operators position according to IEC 704-1:
1982 is equal or less then 70dB(A).
Wichtige Sicherheitshinweise (Germany)
1. Bitte lesen Sie diese Hinweise sorgf„ltig durch.
2. Heben Sie diese Anleitung fr den sp„teren Gebrauch auf.
3. Vor jedem Reinigen ist das Ger„t vom Stromnetz zu trennen. Verwenden Sie keine
Flssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung.
4. Die Netzanschlu ásteckdose soll nahe dem Ger„t angebracht und leicht zug„nglich sein.
5. Das Ger„t ist vor Feuchtigkeit zu schtzen.
6. Bei der Aufstellung des Ger„tes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen
k”nnte Besch„digungen hervorrufen.
7. Die Belftungs”ffnungen dienen der Luftzirkulation, die das Ger„t vor šberhitzung schtzt.
Sorgen Sie dafr, daá diese ™ffnungen nicht abgedeckt werden.
8. Beachten Sie beim Anschluá an das Stromnetz die Anschluáwerte.
9. Verlegen Sie die Netzanschluáleitung so, daá niemand darber fallen kann. Es sollte auch
nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen, die sich am Ger„t befinden, sind zu beachten.
11. Wird das Ger„t ber einen l„ngeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz
trennen. Somit wird im Falle einer šberspannung eine Besch„digung vermieden.
12. Durch die Lftungs”ffnungen drfen niemals Gegenst„nde oder Flssigkeiten in das Ger„t
gelangen. Dies k”nnte einen Brand bzw. elektrischen Schlag ausl”sen.
13. ™ffnen sie niemals das Ger„t. Das Ger„t darf aus Grnden der elektrischen Sicherheit nur
von authorisiertem Servicepersonal ge”ffnet werden.
14. Wenn folgende Situationen auftreten ist das Ger„t vom Stromnetz zu trennen und von einer
qualifizierten Servicestelle zu berprfen:
a. Netzkabel oder Netzstecker sind besch„digt.
b. Flssigkeit ist in das Ger„t eingedrungen.
c. Das Ger„t war Feuchtigkeit ausgesetzt.
d. Wenn das Ger„t nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe
dieser Anleitung keine Verbesserung erzielen.
e. Das Ger„t ist gefallen und/oder das Geh„use ist besch„digt.
f. Wenn das Ger„t deutliche Anzeichen eines Defektes aufweist.
15. Zum Netzanschluá dieses Ger„tes ist eine geprfte Leitung zu verwenden. Fr einen
Nennstrom bis 6A und einem Ger„tegewicht gr”áer 3kg ist eine Leitung nicht leichter als
H05VV-F, 3G, 0.75mm 2 einzusetzen.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betr„gt 70dB(A)
oder weniger.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.