DEVAPPS1.INF Driver File Contents (6133.zip)

[Identification]
      OptionType = TAPE
  [SystemVariables]
         STF_WINDOWSSYSPATH = "" ? $(!LIBHANDLE) GetWindowsNtSysDir
     STF_NTPATH = "" ? $(!LIBHANDLE) GetWindowsNtSysDir
     STF_WINDOWSPATH = "" ? $(!LIBHANDLE) GetWindowsNtDir
 [ExternalInstallOption]
      Debug-Output "Entering ExternalInstallOption"
     Set !G:DebugOutputControl = 1
      set Exit_Code   = $(!SETUP_ERROR_GENERAL)
     install LoadSetupLibrary
     LoadLibrary "x" $(!STF_CWDDIR)setupdll.dll !LIBHANDLE
     set STF_CONTROLSET = CurrentControlSet
     read-syms SystemVariables
     Detect    SystemVariables
     ifstr(i)      $(INF_SECTION)  == ""
      Debug-Output "INF_SECTION is empty"
      goto end
     else-ifstr(i)      $(STF_LANGUAGE)  == ""
         Debug-Output "STF_LANGUAGE is empty"
    goto end
     else-ifstr(i) $(INFFILE)       == ""
         Debug-Output "INIFILE  is empty"
         goto end
     endif
     ifstr(i)      $(INF_SECTION)  == "InstallOption"
         Debug-Output "InstallOption section"
         ifstr(i) $(OPTION)        == ""
           Debug-Output "OPTION  is empty"
           goto end
         else-ifstr(i) $(INITSRC)       == ""
           Debug-Output "INITSRC  is empty"
           goto end
         else-ifstr(i) $(ADDCOPY)       == ""
           Debug-Output "ADDCOPY  is empty"
           goto end
         else-ifstr(i) $(DOCOPY)        == ""
           Debug-Output "DOCOPY  is empty"
           goto end
         else-ifstr(i) $(DOCONFIG)        == ""
           Debug-Output "DOCONFIG  is empty"
           goto end
endif 
          Debug-Output "Before Shel command"
          shell $(INFFILE) $(INF_SECTION) $(STF_LANGUAGE) $(OPTION) $(INITSRC) $(ADDCOPY) $(DOCOPY) $(DOCONFIG)
          Debug-Output "After Shel command"
       else-ifstr(i)      $(INF_SECTION)  == "NetInstallOption"
         Debug-Output "Entering NetInstallOption"
         Set !STF_CWDIR = $(!STF_WINDOWSSYSPATH)
          Shell NCPARAM.INF Param_SetGlobals
          LoadLibrary "x" $(!STF_CWDIR)\ncpa.cpl !NCPA_HANDLE
 	      LoadLibrary "x" $(!STF_CWDIR)\setupdll.dll !LIBHANDLE
          Shell "NCPARAM.INF" Param_ControlDetection DTSTART
 	      set !NTN_RegBase      = $(INF_NET_REG_BASE)
 	      set !NTN_SoftwareBase = "Software"
 	      set !NTN_ServiceBase  = "System\CurrentControlSet\Services"
          set !STF_HWND = $(MY_APP_WHND)
	      Debug-Output "Setting default net option"
          set !NTN_InstallMode  = install
          SET !STF_INSTALL_MODE = install
          ifstr(i) $(INF_SECTION_OP) == "R"
            Debug-Output "Removing net option"
            set !NTN_InstallMode  = deinstall
          else-ifstr(i)  $(INF_SECTION_OP)  == "C"
            Debug-Output "Config net option"
            set !NTN_InstallMode  = configure
          endif
          Debug-Output "Before Shel command"
          set !STF_BUSTYPELIST = {PCMCIA} 
          Shell $(INFFILE) InstallOption $(STF_LANGUAGE) $(OPTION) $(!STF_CWDIR) "YES" "YES" "NO"
          ifstr(i) $($R0) == STATUS_SUCCESSFUL
            set Exit_Code = $(!SETUP_ERROR_SUCCESS)
          else-ifstr(i) $($R0) == STATUS_USERCANCEL
            set Exit_Code = $(!SETUP_ERROR_USERCANCEL)
           goto end
         endif
          Set NCPA_CMD_LINE = " /t STF_INSTALL_MODE = EXPRESS"
         Set NCPA_FUNC = NCPA
          LibraryProcedure NCPA_RESULT $(!NCPA_HANDLE),CPlSetup $(!STF_HWND), $(NCPA_FUNC), $(NCPA_CMD_LINE) 
          Debug-Output "Before end"
 Debug-Output "After Shel command"
     else-ifstr(i)      $(INF_SECTION)  == "DeInstallOption"
          Debug-Output "DeInstallOption"
          ifstr(i) $(OPTION)        == ""
            Debug-Output "OPTION"
            goto end
          endif
          shell $(INFFILE) $(INF_SECTION) $(STF_LANGUAGE) $(OPTION)
     else-ifstr(i)      $(INF_SECTION)  == "GetInstalledOptions"
          shell $(INFFILE) GetInstalledOptions $(STF_LANGUAGE)
          endif
     ifint $($ShellCode) != $(!SHELL_CODE_OK)
          Debug-Output "Execing Configuring hardware fail"
         goto finish_InstallOption
     endif
     Debug-Output "Before end"
     ifstr(i) $($R0) == STATUS_SUCCESSFUL
         set Exit_Code = $(!SETUP_ERROR_SUCCESS)
     else-ifstr(i) $($R0) == STATUS_USERCANCEL
         set Exit_Code = $(!SETUP_ERROR_USERCANCEL)
     endif
 end =+
     Debug-Output "IN END"
     install   FreeSetupLibrary
     FreeLibrary $(!LIBHANDLE)
     exit
 [Source Media Descriptions]
     1  = "Windows NT Workstation Setup Disk #1"  , TAGFILE = disk1
     2  = "Windows NT Workstation Setup CD-ROM"  , TAGFILE = disk2
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web1, load: 0.77