INSTALLATION INSTRUCTIONS FOR
16-BIT NDIS 2.01 DRIVER FOR DOS/WINDOWS AND OS/2 WITH
HP DeskDirect PCI LAN ADAPTER
The Network Driver Interface Specification (NDIS) 2.01 is a 16-bit driver
used by many DOS and OS/2 networking products to gain access to the LAN.
The HP NDIS 2.01 drivers are self-configuring, which means the driver will
automatically locate and read the HP DeskDirect PCI LAN card's configuration.
Only the DRIVERNAME parameter needs to be present under the [HPFEND] section
in the PROTOCOL.INI file.
The 16-bit NDIS 2.01 drivers are located on the HP Support Disk:
\IBMLS\DOS\HPFEND.DOS - 16-bit NDIS 2.01 driver for DOS and Windows
\IBMLS\OS2\HPFEND.OS2 - 16-bit NDIS 2.01 driver for OS/2
To install the HP DeskDirect PCI LAN Card and its 16-bit NDIS 2.01 DOS or
OS/2 driver, follow the instructions below:
NOTE: Throughout these instructions, the term 'HP LAN Card' will be used to
refer to the HP DeskDirect PCI LAN Adapter.
1. Install the HP LAN Card, and optionally, run HPVGSET.
Follow instructions in the 'Setting Up Your Card and LAN Connection'
chapter of the Installation Guide.
2. Install the networking product onto the PC.
Completely install the networking product.
NOTE: If the product requires that a driver be given and it cannot
read the HP NDIS 2.01 driver off this disk, then pick any other
driver to install. In steps 4 and 5 below, when editing the
PROTOCOL.INI and CONFIG.SYS files, change all occurances of that
driver's name to HPFEND.
3. Copy the NDIS 2.01 driver from the HP Support Disk.
Create a directory on the computer. For example,
C:
MKDIR \NDIS2
Copy the NDIS 2.01 driver file from HP Support Disk this directory.
For DOS computers with the HP Support Disk in floppy drive A:
COPY A:\IBMLS\DOS\HPFEND.DOS C:\NDIS2
For OS/2 computers with the HP Support Disk in floppy drive A:
COPY A:\IBMLS\OS2\HPFEND.OS2 C:\NDIS2
4. Edit the PROTOCOL.INI file with a text editor.
Locate the PROTOCOL.INI file within the networking product's directory
created in step two.
The PROTOCOL.INI file must include a section describing the LAN adapter
(i.e. a [HPFEND] section) and a section describing each of the network
products being run. Each network product section must include a
a BINDINGS statement.
For a complete description of all the parameters used by the HP
DeskDirect PCI NDIS 2.01 driver, refer to the PROTOCOL.TXT file
under \NDIS2 directory of the HP Support Disk.
Here is an example section for the HP DeskDirect PCI LAN Adapter card
shown below:
; HP DeskDirect PCI LAN Adapter
[HPFEND_PCI]
drivername = HPFEND$
; adaptertype = 3
; adapterslot =
; ioaddress =
; memorymapbase =
; maxhwtrans = 10
; maxswtrans = 2
; maxmulticast = 5
; maxicnest = 1
; priority = no
; usebootrom = no
; busmaster = yes
; netaddress = "080009010203"
All the optional parameters have been commented out (using the ';'
character) and are shown here only to illustrate the defaults.
Only the DRIVERNAME parameter is mandatory.
The PROTOCOL.INI file must be merged with the networking product's
PROTOCOL.INI. BINDINGS statements must be created to identify the
HP DeskDirect PCI NDIS 2.01 driver to the networking product's
protocol modules.
An example PROTOCOL.INI file that supports FTP PC/TCP might look like
the following:
; FTP's software
[PKTDRV]
drivername = PKTDRV$
intvec = 0x65
bindings = HPFEND <--- Add this line
; HP DeskDirect PCI LAN Adapter
[HPFEND] <--- Add this line
DRIVERNAME = HPFEND$ <--- Add this line
5. Edit the CONFIG.SYS file.
The CONFIG.SYS file must be modified to include DEVICE statements
for the PROTMAN.DOS (or PROTMAN.OS2) driver, for the HPFEND driver,
and any of the drivers for the networking product being used.
An example portion of a DOS CONFIG.SYS file that supports the HP
DeskDirect PCI LAN card and FTP PC/TCP version 2.2 is shown below:
REM************************************************
REM FTP software, run startftp after bootup ***
REM************************************************
DEVICE = C:\FTP\PROTMAN.DOS /I:C:\FTP
DEVICE = c:\FTP\DIS_PKT.GUP
REM***********************************************
REM HP DeskDirect PCI LAN NDIS 2.01 DRIVER ***
REM***********************************************
DEVICE = C:\NDIS2\HPFEND.DOS
Please refer to FTP PC/TCP's Installation Manual for details.
Notes on the PROTMAN driver:
- PROTMAN must be loaded before the adapter driver and the networking
drivers; that is, the DEVICE statement for the PROTMAN driver must be
located before the other network DEVICE statement.
- The "/I:" parameter in the DEVICE statement for the PROTMAN driver
identifies the path to the PROTOCOL.INI file. In the example above,
PROTOCOL.INI is located in the directory C:\FTP.
6. Reboot the computer and execute NETBIND.EXE
To activate the modified PROTOCOL.INI and CONFIG.SYS files, reboot
the computer. When the boot process is complete, run NETBIND.EXE.
This file is included with the networking product software. NETBIND
must be run each time the system is booted, so it is recommended
NETBIND.EXE be added to the AUTOEXEC.BAT file.
<End of File>
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.