Linksys EtherFast Series LAN Cards README File
for Windows 95
Copyright (C) 1997 Linksys, All Rights Reserved
------------------------------------------------
CONTENTS:
Before You Begin
Setup
Enabling File & Printer Sharing
Technical Support
Before You Begin
----------------------------------------------------------------------
Thank you for purchasing your EtherFast 10/100 LAN Card from Linksys.
The instructions below explain how to set up the card's network
software drivers for use with your particular network operating system
like Windows 95, Novell, Unix, etc.
The EtherFast card is built for use in 32-bit, Plug-and-Play desktop
computers with auto-configuring PCI slots. It must be used in your
PC's bus master PCI slot. For further information, see the User Guide
that came with the card.
When a PCI card is used in a computer that has a Plug-and-Play BIOS
(Basic Input/Output System), the card is automatically configured by
the PC each time the machine is booted. The card's IRQ, memory address,
and other operating parameters are automatically assigned. There is
no way to change a Plug-and-Play card's IRQ and other settings outside
of the BIOS menu(s) that your computer providse. If the resources that
are assigned to your EtherFast card seem to conflict with other devices
in your computer, you will need to use your system's BIOS to resolve
the conflicts.
If you have problems configuring your BIOS or resolving IRQ or other
hardware conflicts, consult your computer manual or contact your PC's
manufacturer for BIOS setup & configuration directions.
Here are some general guidelines to follow when installing a PCI card
(like the EtherFast card) into your computer:
* If you need to configure your PC's BIOS in order to resolve an
IRQ or other conflict with the EtherFast card, there are a few
possibilities:
- Your PCI may not allow you to change the IRQ value(s) of
the PCI slot(s). In this case, you will ONLY be able to
use the IRQ & MEM values that have been pre-assigned to
each slot. The popular BIOS from Phoenix, for example,
does not allow you to modify BIOS-assigned IRQ settings.
- You may be able to change the IRQ & MEM values for a given
PCI slot by setting jumpers on your PC's mother board.
Please refer to your PC's motherboard user guide for
specific instructions.
- Your PC may allow you to change the IRQ & MEM values for
a given PCI slot by accessing the PC's BIOS setup menu.
Please refer to your PC's user guide for specific details.
The BIOSs from companies like AMI and Award are fully
customizable from their BIOS menus, for example.
* When loading the EMM386.EXE program in your computer's CONFIG.SYS,
you MUST use version MS-DOS 6.22 or above. If you load an older
EMM386.EXE program (below DOS 6.22), your computer will hang up while
loading the network driver.
* The EtherFast LAN adapter should be used in a 32-bit PCI slot that
supports PCI Local Bus Mastering. It cannot be plugged into a PCI
Bus Slave slot. Consult your motherboard's documentation for more
information on master & slave slots.
* When using NT, set your BIOS PCI settings, and the PCI settings
within NT itself, to MANUAL. NT is *not* a Plug-and-Play BIOS,
and will not usually recognize LAN cards if they are set to be
automatically detected & configured.
------------------------------------------------
SETUP
------------------------------------------------
Follow the instructions below. Do *not* insert your EtherFast
card until told to do so.
Setup
-----------------------------------------------------------------
1. Turn your computer off. Insert the EtherFast 10/100 LAN Card
into one of your computer's motherboard slots. See the User Guide
if you want step-by-step instructions. Turn your computer back
on when you're finished and start Windows 95.
2. Windows 95 will detect your new hardware. When the New Hardware
menu appears, choose "Select driver disk provided by manufacturer"
and click OK. When 95 asks for the path where the driver is
located, put the EtherFast 10/100 disk into drive A and
press Enter. When "Linksys" appears in the box, press Enter. A window
may appear asking you to insert the EtherFast 10/100 disk. When this
appears, type A:\WIN95 and press Enter. If it appears again, type A:\Win95
and press Enter again. Windows 95 will begin copying files to your
system. You may need your original Windows 95 disks or CD-ROM
to complete the setup. A window may appear requesting your Windows 95
CD-ROM; at this point insert the disk into your CD-ROM Drive and type
the corresponding drive letter (for example D:\WIN95 where (D) is the
drive letter of your CD-ROM drive. Windows may also ask you to supply the
name of your computer and/or workgroup. Enter them. If you don't have
names yet, make up new ones.
Finally, when 95 asks if you want to restart your computer,
click on Yes. Continue with the directions below after
95 starts back up.
3. Click on My Computer, followed by Control Panel. Select the
Network icon. Make sure that the following network protocols
are installed:
4. Upon booting back up, 95 will automatically detect the presence
of the EtherFast card. Follow the instructions on your screen
to complete install it. Then, *before* restarting your computer,
do the following:
5. Click on My Computer, followed by Control Panel. Select the
Network icon. Make sure that the following network protocols
are installed:
Client for Microsoft Networks
Client for NetWare Networks
Linksys EtherFast 10/100 LAN Card
IPX/SPX compatible Protocol
NetBEUI
If any protocols are missing, click on the Add button and add
them in.
6. Click on My Computer, followed by Control Panel. Select the
Network icon. Make sure that the following network protocols
are installed:
Client for Microsoft Networks
Client for NetWare Networks
Linksys EtherFast 10/100 LAN Card
IPX/SPX compatible Protocol
NetBEUI
If any protocols are missing, click on the Add button and add
them in.
7. If you are *not* using Windows 95 with an NT or NetWare file server,
skip the two paragraphs below.
Otherwise:
Using the Card with a NetWare File Server
Click on My Computer, Control Panel, and Network. Change the
Network Logon to Client for NetWare Network. Next, double-click
on the client for NetWare networks. Put your server's name in
the Preferred Server box. Click in the Enable logon script
processing box. Click on OK.
Using the Card with a Windows NT File Server
Click on My Computer, Control Panel, and Network. Change the
Primary Logon to Client for Microsoft Networks. Double-click on
the client for Microsoft networks. Check the Log into Windows NT
domain box. Put your NT domain name in the Windows NT domain
area. Continue with the installation, following any directions
that appear on your screen.
When the setup is complete, choose to restart your computer.
Follow the File & Printer Sharing instructions below. They
explain how to turn on Windows 95 sharing so that other
computers can see your PC and vice-versa.
--------------------------------------------------------------------------
ENABLING FILE & PRINTER SHARING UNDER WINDOWS 95
--------------------------------------------------------------------------
The instructions below explain how to turn on file & printer sharing in
Windows 95. Before following them, make sure that you have already
installed & configured your Linksys network adapter(s).
Getting Started
------------------------------------------------------------------------
1. Start up Windows 95 if you haven't already. Click on the Start button,
followed by Settings, Control Panel, and the Network icon.
2. Click on the Configuration window tab. If you see File and printer
sharing for Microsoft Networks in the list of items that appears,
close the Control Panel and go to Enabling File Sharing or How to
Share Printers below. Otherwise, go to step 3.
3. Click on the File and Print Sharing button.
4. If you want other users to be able to access your files, use your
mouse to put a checkmark next to the I want to be able to give others
access to my files option. If you want others to be able to use
printer(s) that are plugged into your computer, put a checkmark next
to the I want to allow others to print to my printers option.
When you're finished, click on OK. You'll now see a text line that
reads File and printer sharing for Microsoft Networks in the
Configuration list box. (If you don't see it, you might need to use
the scroll bars to scroll through the list). Click on OK. When 95
asks if you want to restart your computer, click on Yes.
Enabling File Sharing
------------------------------------------------------------------------
After following steps 1-4 above, double-click on your My Computer icon.
A window of available disk drives will appear. Using your right mouse
button, click once on the drive that you want to make available to other
users. Click on Sharing, followed by the Sharing tab. Click on Share As.
In the Share Name box, give your computer a name (you can call it whatever
you want--Mary's Computer, etc.).
Next, decide on the type of access that you want to give other users.
* Read-Only access lets other users view the files on your PC.
* Full access lets users create, change, or delete files on your system.
* Depends on Password lets users have Read-Only and/or Full access,
depending on the password that you decide to share with them.
Use your mouse to select the type of file sharing access that you want
other users to have. If you want to assign access password(s), type them
into the Password box(es). When you're done, click on the Apply button,
followed by OK. Your drive(s) can now be accessed from other users
whenever they click on their Windows 95 Network Neighborhood icons. If a
user tries to access one of your drives that's password-protected, he or
she will be asked for the appropriate Read-Only or Full access password.
How to Share Printers
------------------------------------------------------------------------
After following steps 1-4 above, double-click on your My Computer icon.
Click on the Printers folder. A window of available printers will appear.
Using your right mouse button, click once on the printer that you want to
share with other users. Click on Sharing, followed by the Sharing tab.
Click on Share As. In the Share Name box, give a name to the printer
you're about to share (Jack's HP4, for example). If you want to assign a
password to the printer so only certain users can access it, type a
password in the Password box. When you're done, click on the Apply
button, followed by OK. Your printer(s) are now shared.
HOW TO GET TECHNICAL SUPPORT
------------------------------------------------------------------------
There are a variety of methods that you can use to get FREE technical help
or sales information about Linksys products.
Voice & FAX
------------
The Linksys voice line is open during normal business hours, 7-5 p.m.,
Pacific Standard Time. The fax line is available 24 hours a day. When
sending a fax, be sure to include a detailed description of any
problem(s) that you are experiencing.
Technical Support Hotline (714) 261-1288
Fax (714) 261-8868
E-mail
------
To get technical or sales information bounced back to you from Linksys
automatically, send some e-mail to the address below. Include the
name of the product that you want help with, along with the word
HELP, in the subject line of your e-mail. Example: HELP ME WITH THIS
PRODUCT. (If requesting sales information, use the word SALES instead
of HELP).
E-mail Address info@linksys.com
Internet Access
---------------
You can also use your World Wide Web or FTP browser to visit Linksys on
the Internet.
Web Site http://www.linksys.com
FTP File Transfer Site ftp.linksys.com
Bulletin Board System (BBS)
---------------------------
To access the Linksys Bulletin Board System (BBS), set your modem to
8 bits, No parity, 1 stop bit, and call (714) 261-2888. Use a speed
setting of 33.6bps or slower. When downloading files, use the "Z-modem"
download protocol for best results.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.