GPS 17N Software Version 2.60
------------------------------------------------------------
The software version is available via the PGRMT NMEA sentence
The PGRMT sentence can be enabled by transmitting the following
command string the to GPS17N using a terminal program:
$PGRMO,PGRMT,1<CR><LF>
If the GPS 17N is installed with a GMAP 2006/2010, the software
version can be obtained by completing the following steps:
1.Press the MENU key to access the Main Menu.
2.Press the DOWN ARROW key until the System tab is selected.
3.Press the key below the "System Inf" caption.
4.The GPS 17N software version will be displayed on the
screen labeled "Antenna:.
------------------------------------------------------------
Warnings:
If this software is uploaded to a unit other than the product for
which it is designed, you will not be able to operate that unit.
If repeated software upload attempts fail, you may need to return
the unit to GARMIN for service.
------------------------------------------------------------
Notes:
Version 2.04 is the first widespread release software version.
Version 2.04 was released in tandem with the GPS 2006/2010
products.
Version 2.07 is the first widespread release software version
for standalone GPS17N sales.
Any units with software version 2.03 or lower will have
all nonvolatile memory erased when version 2.04 or later is
loaded.
------------------------------------------------------------
Change History
Version 2.60 to 2.70:
1. Improved SBAS search and selection process.
2. Changed software version to 2.70.
------------------------------------------------------------
Change History
Version 2.40 to 2.60:
1. Updated for use with Garmin marine products.
2. Changed software version to 2.60.
------------------------------------------------------------
Change History
Version 2.30 to 2.40:
1. Validate altitude during first-fix processing.
2. Improved EPH during transition from non-differential fix
to a differential fix.
3. Added ability to turn position averaging on and off via a
Garmin or NMEA command.
4. Allow vertical filter to be disabled via the PGRMC
sentence.
5. Enhanced first fix processing.
6. Changed software version to 2.40.
------------------------------------------------------------
Change History
Version 2.20 to 2.30:
1. Improved non-volatile memory storage of WAAS/EGNOS
ionospheric mask corrections.
2. Changed software version to 2.30.
------------------------------------------------------------
Change History
Version 2.11 to 2.20:
1. Improved WAAS/EGNOS satellite selection algorithm to
select the satellite with the most beneficial
corrections given the unit's current position. Units
will not use a WAAS/EGNOS satellite if the unit's current
position is outside of a given WAAS/EGNOS satellite's
service volume.
2. Changed software version to 2.20.
------------------------------------------------------------
Change History
Version 2.10 to 2.11:
1. Obsoleted position pinning. Position pinning remains off
regardless of the PGRMC1 sentence command.
2. Fixed problem with saving unit position in nonvol upon
first fix.
3. Changed software version to 2.11.
------------------------------------------------------------
Change History
Version 2.09 to 2.10:
1. Added automatic position averaging when stopped.
2. Changed software version to 2.10.
------------------------------------------------------------
Version 2.08 to 2.09:
1. Added support for ephemeris download.
2. Fixed problems where leading zeros were not being transmitted
in certain fields of GPRMC and GPVTG.
3. Improve eph estimate for WAAS DGPS fixes.
4. Changed software version to 2.09.
------------------------------------------------------------
Version 2.07 to 2.08:
1. Made improvements to alleviate the "LOST GPS FIX" messages
that were occurring on the West Coast.
2. Changed software version to 2.09.
---------------------
Version 2.06 to 2.07:
1. Fix problem where WAAS processing could cause the unit to
lock up.
2. Changed software version to 2.07.
---------------------
Version 2.05 to 2.06:
1. Fixed problem on where WAAS processing could cause the unit
to lock up if tracking more than one WAAS satellite.
2. Changed software version number to 2.06.
---------------------
Version 2.04 to 2.05:
1. Implement better validity checking on dates to prevent the
date from being incorrectly set far in the future.
2. Improved NMEA sentence processing to prevent long dropouts
in the NMEA sentence stream.
3. Changed software version number to 2.05.
------------------------------------------------------------
Upload Instructions - Serial Port Update:
Instructions for uploading the new software to your GPS17N using Microsoft
Windows 95 or later:
1. Download the appropriate self-extracting archive file onto your hard drive.
2. Unzip the files in the archive by running the downloaded executable file.
3. Connect your unit to a free serial port (Com 1, 2, 3, or 4) on your PC. The
user will need to build an appropriate cable to accomplish this.
4. Power up the unit. Use a terminal program on your PC and connect to the
serial port. NMEA sentences should begin streaming by in the terminal
program.
5. The unit will need to be changed from NMEA mode to a programming mode. To
do this, transmit the following string using the terminal program:
$PGRMO,,G<CR><LF>
The unit will stop transmitting NMEA sentences and switch to the programming
mode. At this point, disconnect the terminal program from the serial port.
6. Change to the directory in which you unzipped the files, (i.e., C:\GARMIN),
and run the update program, updater.exe. Select the appropriate serial
port and click "OK" to begin the software upload.
During the upload, the display will indicate "Software Loading...."
The upload process should take 1-3 minutes to complete. When the upload
is completed, the unit will reset itself and turn on normally. At this
point, connect the terminal program to the serial port and NMEA sentences
should be streaming by.
------------------------------------------------------------
Upload Instructions - USB Card Programmer Update. The GPS 17N
can be programmed in-situ via a GMAP 2006 or GMAP 2010 data
card
Instructions for uploading the new software using a USB Card Programmer:
1. Download the appropriate self-extracting archive file onto your hard drive.
2. Unzip the files in the archive by running the downloaded executable file.
3. Make sure a USB Card Programmer is connected to your computer, and that a
data card is inserted into the programmer.
4. Change to the directory in which you unzipped the files, (i.e., C:\GARMIN),
and run the update program, program_card.exe. Select "Card Programmer"
and click "OK" to begin the software upload.
5. Remove the data card from the USB Card Programmer. Make sure that your GPS
unit is powered on and insert the data card into the unit to begin
uploading the software to the unit. During the upload, the display will
indicate "Software Loading...". The upload process should take 1-5 minutes
to complete. When the upload is completed, the unit will reset itself and
turn on normally.
------------------------------------------------------------
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.