GARMIN eTrex Summit Software Upgrade Information ------------------------------------------------------------ WARNINGS: If this software is uploaded to a GPS unit other than the product for which it is designed, you will not be able to operate that unit. If the upload software fails, verify that you have good batteries installed and try again. If repeated upload attempts fail, you may need to return the unit to GARMIN for service. ------------------------------------------------------------ Instructions for uploading the new software to your eTrex Summit using Microsoft Windows 95/98/NT: 1. Download the appropriate self-extracting archive file for your eTrex Summit onto your hard drive. 2. Unzip the files in the archive by running the downloaded executable file. 3. Connect your eTrex Summit to a free serial port (Com 1, 2, 3, or 4) on your PC with a PC interface cable. 4. Turn on your eTrex Summit and ensure the Serial Data Format is set to "GARMIN". You can find this setting in Menu Page -> Setup -> Interface. 5. Change to the directory in which you unzipped the files, (i.e., C:\GARMIN), and run the update program, updater.exe. Select the appropriate serial port and click "OK" to begin the software upload. During the upload, the eTrex Summit's display will indicate "SWT LOADING" The upload process should take 3-10 minutes to complete. When the upload is completed, the eTrex Summit will reset itself and turn on normally. ------------------------------------------------------------ Changes Made from Versions 2.40 to 2.50: 1. Removed potential shutdown when navigating route points placed close to one another. 2. Updated French translations. ------------------------------------------------------------ Changes Made from Versions 2.30 to 2.40: 1. Corrected problem with Sight N Go shutdown. ------------------------------------------------------------ Changes Made from Versions 2.20 to 2.30: 1. Added Indian grid support. 2. Added distance in Yard support. ------------------------------------------------------------ Changes Made from Versions 2.13 to 2.20: 1. Corrected problem that could potentially split tracklog into many small segments. The tracklog will still segment each time unit enters or leaves poor coverage and plot elevation points when it does not have a lock on satellites. ------------------------------------------------------------ Changes Made from Versions 2.12 to 2.13: 1. Changed tracklog operation to break track line segments between power cycles. ------------------------------------------------------------ Changes Made from Versions 2.11 to 2.12: 1. Corrected problem assigning the selected map datum. 2. Changed operation to continue updating elevation related data when satellite reception has been lost. ------------------------------------------------------------ Changes Made from Versions 2.10 to 2.11: 1. Added RT 90 position format. 2. Corrected the output of the heading NMEA sentence. ------------------------------------------------------------ Changes Made from Versions 2.07 to 2.10: 1. No users visible change. Added software compatibility for alternative hardware configurations. ------------------------------------------------------------ Changes Made from Versions 2.06 to 2.07: 1. Fixed distortion detection algorithm so that the "HOLD LEVEL" message will work properly in high declination areas of the world. 2. Added Czech and Polish languages. 3. Corrected some translations for the Dutch language. 4. Prevented selecting Sight 'N Go option from the Compass page when the compass is not calibrated or if the unit does not have a good position fix. 5. Corrected New Zealand position format selection. 6. Changed UTC offset for the Moscow time zone to +3:00. 7. Removed UTC and LCL labels from sunrise and sunset times. 8. When selecting a route to follow, the first and last waypoint names, used to determine which direction to navigate, are displayed correctly for all languages. ------------------------------------------------------------ Changes Made from Versions 2.05 to 2.06: 1. Added an Advanced Skyview mode on the GPS page that displays the location in the sky of each satellite that the unit is tracking. Along with this skyview is the signal strength for each satellite. To get to this new mode press the ENTER key while on the GPS page and an option menu will appear. This option menu contains two items: SETUP DISPLAY and ADVANCED SKYVIEW. The SETUP DISPLAY option will take you to the Display Setup page for adjusting contrast and light controls. Selecting the ADVANCED SKYVIEW option will switch the GPS page to display the advanced skyview information. 2. User now has the option to display the normalized pressure or local ambient pressure on the Elevation page cycle field. The option to switch between these displays is on the System Setup page. The normalized pressure is referenced against the last calibrated altitude or pressure and is not referenced against GPS altitude. 3. Added multiple language support. From the System Setup page you can select from 12 different languages. 4. Fixed the save track bug that was introduced in version 2.05. 5. Fixed the elevation profile of saved tracks to display the correct distance. 6. Fixed Max/Min elevation recording. ------------------------------------------------------------ Changes Made from Versions 2.04 to 2.05: 1. Allow display of speed and track when velocity is below 1.0 MPH and selective availability is off. 2. Fixed altimeter Auto Calibration so that it can be turned off and on correctly. 3. Fixed altimeter calibration problem where the new setting did not always get saved between power cycles. 4. Fixed route leg distance calculation that occurred when the unit did not have a fix. 5. Prevent rare occurrences of showing Compass heading when set to GPS only. 6. Removed local pressure from the cycle field on the Elevation page since it was causing confusion. 7. Added Vertical Speed to the cycle field on the Elevation page. 8. When GPS and Compass are off, the Map page will no longer display invalid characters under the directional symbol. 9. Fixed Dutch grid conversions and added new Dutch map datum to accompany the Dutch grid. 10. The map datum list on the Units Setup page is now displayed alphabetically. 11. Added an angle setup on the Units Setup page that allows you to display angles in Degrees or Mils. ------------------------------------------------------------ Changes Made from Versions 2.03 to 2.04: 1. Improvements in positioning to fix erroneous track logs. 2. Improved the arrival alarm. 3. Changed the meter unit symbol from 'mt' to 'm' to be consistent with international standards. ------------------------------------------------------------ Changes Made from Versions 2.02 to 2.03: 1. The UTC label is no longer displayed on the time when the UTC offset is zero. 2. The user selected north reference offset is saved correctly. 3. The restore defaults button on the units setup page saves the defaults correctly. 4. Shortened the Australian grid abbreviations in the map datum list. 5. Added Support for NMEA magnetic heading sentence $HCHDG -- Heading, Deviation, and Variation sentence with HEADING SENSORS: Compass, Magnetic talker ID. ------------------------------------------------------------ Changes Made from Versions 2.01 to 2.02: 1. Added multiple routes (up to 20 routes with 50 waypoints per route). NOTE: THE CURRENT ROUTE IN THE ETREX SUMMIT WILL BE DELETED! To save the current route, transfer the route to a PC before performing the upgrade, then transfer back to the eTrex Summit after performing the upgrade. 2. Editing the location of a waypoint is now displayed correctly. 3. Altimeter calibration using GPS is improved to get a smoother, more accurate vertical reference.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.