CNET PRO200WL PCI Fast Ethernet Adapter NDIS MAC Driver for LAN Manager 2.x Workstation/Server Installation Guide ========================================================= Installation Procedure ====================== 1. Introduction =============== This document describes the procedure to setup LAN Manager 2.1 Workstation/Server driver for the PCI Fast Ethernet Adapter. 2. Location of Driver ===================== (DOS) \NDIS20\DOS\DM9PCI.DOS (OS/2)\NDIS20\OS2\DM9PCI.OS2 3. Sample Configuration Files ============================= CONFIG.SYS (for DOS will contain) %%% DEVICE=C:\LANMAN.DOS\DRIVERS\PROTMAN\PROTMAN.DOS /I:C:\LANMAN.DOS DEVICE=C:\LANMAN.DOS\DRIVERS\ETHERNET\DM9PCI\DM9PCI.DOS CONFIG.SYS (for OS/2 will contain) %%% DEVICE=C:\LANMAN.OS2\DRIVERS\PROTMAN\PROTMAN.OS2 /I:C:\LANMAN.OS2 DEVICE=C:\LANMAN.OS2\DRIVERS\ETHERNET\DM9PCI\DM9PCI.OS2 PROTOCOL.INI (will contain) %%% [DM9PCI_NIF] ; PROTOCOL.INI SAMPLE DriverName = DM9PCI$ ; ; SLOT = 1 ; This parameter specifies the slot number used for notifications. ; For PCI slot , you can specify from 1 to 16. ; ; MEDIA_TYPE = AUTODETECT ; MEDIA_TYPE = FM_100M_FULL ; MEDIA_TYPE = FM_100M_HALF ; MEDIA_TYPE = FM_10M_FULL ; MEDIA_TYPE = FM_10M_HALF ; Note: ; AUTODETECT ; --> Auto detect the data rate and duplex mode ; FM_100M_FULL ; --> Forced 100M Full Duplex Mode ; FM_100M_HALF ; --> Forced 100M Half Duplex Mode ; FM_10M_FULL ; --> Forced 10M Full Duplex Mode ; FM_10M_HALF ; --> Forced 10M Half Duplex Mode ; ; This parameter specifies the connector type configuration ; (data rate and duplex mode) of the network adapter card. 4. NDIS Driver Installation on LAN Manager v2.1 =============================================== Before you start with the installation process, make sure that the adapter is properly installed and configured. Besides, make sure your Microsoft LAN Manager is properly installed too. a. Run the appropriate Microsoft LAN Manager of SETUP.EXE for computer you are setting up.(DOS, OS/2 or OS/2 Server). Select "Configuration" item since the adapter driver isn't included on the LAN Manager disk, insert the adapter driver diskette, select the item "PCI Fast Ethernet Adapter NDIS2 MAC Driver" and follow the directions. b. When completed, reboot your computer. 5. NDIS Driver Installation on LAN Manager v2.2x ================================================ a. Type setup in the LAN Manager directory and press <Enter>. The Microsoft LAN Manager Setup screen should appear. b. Choose "Network Drivers" from the "Configuration" field. Press <Enter> to confirm your choice. c. Choose <Add New Config> and press <Enter> to display a list of Network Adapter Drivers. d. Choose <Other Driver> and press <Enter>. e. Insert the Driver Diskette into drive A: or B: of your PC. Indicate the drive location A: or B: of the diskette and select <OK> to proceed. f. Select the appropriate Network Adapter Driver from the list. For example, select "CNET PRO200WL PCI Fast Ethernet Adapter", Select <OK> to confirm your choice. g. Select an appropriate protocol. Use the <Space bar> to mark your choice. If you select TCP/IP protocol, you will be prompted to issue the IP address, the subnet mask, and the default gateway (router). By default, the workstation number of NetBIOS session is set to 6. Please consult Microsoft LAN Manager Installation Manual for more detail or check the online help. h. Select <OK> to confirm your choice. A "Configuration Complete" message should appear on the screen. i. Save the configuration. Select <Save>. j. Press <F3> to exit.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.