ERROR MESSAGE:
****************************************
* ASPI Manager Not Installed. *
* Driver Unloaded. *
****************************************
Possible Cause:
KMECD.SYS could not start because the ASPI Manager (ASPIOMGR.SYS,
ASPIO365.SYS) has not started yet.
Solution:
Reinstall the Software.
ERROR MESSAGE:
****************************************
* Card Information Not Found. *
* Driver Unloaded. *
****************************************
Possible Cause:
* The supplied Interface Card is not properly inserted into the
PC card slot.
* Wrong memory base address which is specified at "/MEM=".
(ASPIO365.SYS only)
Solution:
* Insert the supplied Interface Card.
* Try to change the value of "X" option in EMM386.EXE.
* Make sure the value specified in "/MEM=" option agrees with the
area specified in "X" option of EMM386.EXE.(ASPIO365.SYS only)
* Try to change the value of "/MEM=" option and "X" option in
EMM386.EXE.(ASPIO365.SYS only)
ERROR MESSAGE:
****************************************
* Card Services Program Not Loaded. *
* Driver Unloaded. *
****************************************
Possible Cause:
The ASPIOMGR.SYS couldn't start because the Card Service program
did not load.
Solution:
* Reinstall the Card Service Program supplied with your computer.
If your computer did not come with a Card Service program,
a program is supplied with this Player that will operate your
CD-ROM.
* Confirm the description in the CONFIG.SYS.
Check the CONFIG.SYS to make sure that the ASPIOMGR.SYS is
located after the Card Service. If not, please edit and correct
the placement of the device drivers.
* Edit the CONFIG.SYS to change the value of "X" at EMM386.EXE
(EMS driver).
ERROR MESSAGE:
****************************************
* CD-ROM Drive Not Found. *
* Driver Unloaded. *
****************************************
Possible Cause:
This message tells you that the CD-ROM player does not respond.
1. Hardware trouble such as improper connection between the
Player and your computer (-> Solution 1).
2. Software trouble such as improper running of the ASPI Manager
(-> Solution 2).
3. Card Services and Socket Service that are not supported are being
used (-> Solution 3).
Solution:
1. Check whether the Player is connected properly and if the
power is turned on.
Confirm that the SCSI ID is set properly.
2. Reinstall the software.
3. If the message still appears, copy ASPIO365.SYS from your Setup
disk to your hard disk (copy A:\DOS\ASPIO365.SYS C:\CDRM8).
Edit the CONFIG.SYS file (refer to your DOS manual) from
DEVICE=C:\CDRM8\ASPIOMGR.SYS to DEVICE=C:\CDRM8\ASPIO365.SYS.
ERROR MESSAGE:
************************************************
* Device Driver not found: 'PCMCIACD'. *
* No valid CDROM device driver selected *
************************************************
Possible Cause:
1. The KMECD.SYS is not confirmed, or it is unloaded because of
errors.
2. The CD-ROM driver name specified on the (/D) option of KMECD.SYS
must match with the one specified on the (/D) option of
MSCDEX.EXE.
Solution:
1. Edit the CONFIG.SYS to
DEVICE=C:\CDRM8\KMECD.SYS /D:PCMCIACD
(refer to your DOS manual for instructions on how to edit).
2. Edit the AUTOEXEC.BAT to
C:\CDRM8\MSCDEX.EXE /D:PCMCIACD
3. Restart your computer.
ERROR MESSAGE:
****************************************
* Invalid Base Address. *
* Driver Unloaded. *
****************************************
Possible Cause:
Wrong base address of I/O port which is specified at "/PORT=".
Solution:
* Reinstall the software.
* Edit the CONFIG.SYS. Change the "/PORT=" option to confirm to
the base address of I/O port.
* Specify one of the following addresses at "/PORT=".
(140, 180, 220, 230, 240, 250, 260, 270, 280, 290, 300, 320)
ERROR MESSAGE:
************************************************
* Not enough drive letters available *
************************************************
Possible Cause:
Insufficient drive letter (such as N:) is assigned to the CD-ROM
player.
Solution:
When a drive letter other than A-M is assigned to the CD-ROM
player, the display shows the above message.
In this case, follow the instructions below.
1. Edit the CONFIG.SYS to LASTDRIVE=R, for example.
(refer to your DOS manual for instructions on how to edit).
2. Restart your computer.
ERROR MESSAGE:
****************************************
* Unable to get I/O Window. *
* Driver Unloaded. *
****************************************
Possible Cause:
I/O window which is specified at "/PORT=" is already being used.
Solution:
1. Edit the CONFIG.SYS to change the I/O base address which was
specified at "/PORT=" option. Available addresses are 140,
180, 220, 230, 240, 250, 260, 270, 280, 290, 300, 320.
2. Then, restart your computer.
ERROR MESSAGE:
****************************************
* Unable to get IRQ Vector. *
* Driver Unloaded. *
****************************************
Possible Cause:
The IRQ vector which is specified at default is already being
used.
Solution:
Edit the CONFIG.SYS. Add "/INT=" option and specify a suitable
IRQ number.
If you're using SystemSoft Card Service, choose a number from the
"IRQ=" entries in the CSALLOC.INI file.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.