;*********************************************************************** ; ; Windows NT 4 Network Setup File (for NDIS4) ; Xircom Cardbus Ethernet 10/100 Network Adapters ; (c) 1996-1999 Xircom, Inc. ; ; $Revision: 1.22 $ ; $Date: 14 Apr 2000 15:51:32 $ ; ;*********************************************************************** [Identification] OptionType = NetAdapter [PlatformsSupported] ISA EISA MCA PCI [Options] CBE [OptionsTextENG] CBE = "Xircom CardBus Ethernet 10/100 Adapter" [AllFileConstants] GenericInfVersion = " v3.10" ; File names, etc. ---------------------------------------- UtilityInf = "UTILITY.INF" ParamInf = "NCPARAM.INF" subroutineinf = "SUBROUTN.INF" SoftwareType = "driver" Exit_Code = 0 ; EventLog Message File ---------------------------------------- NetEventDLL = "%SystemRoot%\System32\netevent.dll" IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll" ; Product Info ---------------------------------------- Manufacturer = "Xircom" ; Flow control variables ---------------------------------------- ;DISABLEPCMCIASYS = "1" DISABLEPCMCIASYS = "0" [FileConstants-CBE] GenericAdapterName = "Xircom CardBus Ethernet 10/100" GenericDriverName = "Xircom CardBus Ethernet 10/100" GenericSysName = "CBEN4.sys" GenericName = "CBE" ; Product Info ---------------------------------------- ProductMajorVersion = "3" ProductMinorVersion = "10" ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion) ; Software ---------------------------------------- ProductSoftwareName = "CBE" ProductSoftwareDescription = "Xircom CardBus Ethernet 10/100" ProductSoftwareImagePath = "\SystemRoot\System32\drivers\"$(GenericSysName) NetRuleSoftwareType = "cbeSys ndisDriver cbeDriver" NetRuleSoftwareUse = $(SoftwareType) NetRuleSoftwareBindForm = """cbeSys"" yes no container" NetRuleSoftwareClass = {"cbeDriver basic"} NetRuleSoftwareBindable = {"cbeDriver cbeAdapter non exclusive 100"} ; Hardware ---------------------------------------- ProductHardwareName = "CBE" ProductHardwareDescription = "Xircom CardBus Ethernet 10/100" NetRuleHardwareType = "cbe cbeAdapter" NetRuleHardwareBindForm = " yes yes container" NetRuleHardwareClass = {"cbeAdapter basic"} ; Registry Key ---------------------------------------- ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion" ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters" ; Tuple Information ----------------------------------- VERS1Manufacturer = "Xircom" VERS1Product = "CardBus Ethernet 10/100" VERS1Product2 = "CardBus Ethernet II 10/100" VERS1Product3 = "RealPort2 CardBus Ethernet 10/100" VERS1Type = "CBE-10/100" PCMCIA = 0 PCIVendorID = 4445 [GeneralConstants] ; Program flow control variables. from = "" to = "" ; Return codes; Exit_Code is set to one of these ExitCodeOk = 0 ExitCodeCancel = 1 ExitCodeFatal = 2 KeyNull = "" MAXIMUM_ALLOWED = 33554432 RegistryErrorIndex = NO_ERROR KeyProduct = "" KeyParameters = "" TRUE = 1 FALSE = 0 NoTitle = 0 ExitState = "Active" OldVersionExisted = $(FALSE) DriverPath = $(!STF_NTPATH)\drivers ;--------------------------------- ; Default list choices ;--------------------------------- DEFAULT_MEMORY = 26 DEFAULT_IO = 30 DEFAULT_IRQ = 7 [date] ; Now is a list which contains { Sec from 1-1-1970, Year, Month, Day, Hour, ; Minute, Second } Now = {} ? $(!LIBHANDLE) GetSystemDate ;--------------------------------------------------------------------------- ; 1. Identify ; ; DESCRIPTION: To verify that this INF deals with the same type of options ; as we are choosing currently. ; ; INPUT: None ; ; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL ; $($R1): Option Type (COMPUTER ...) ; $($R2): Diskette description ;--------------------------------------------------------------------------- [Identify] ; ; read-syms Identification set Status = STATUS_SUCCESSFUL set Identifier = $(OptionType) set Media = #("Source Media Descriptions", 1, 1) Return $(Status) $(Identifier) $(Media) ;------------------------------------------------------------------------ ; 2. ReturnOptions: ; ; DESCRIPTION: To return the option list supported by this INF and the ; localised text list representing the options. ; ; ; INPUT: $($0): Language used. ( ENG | FRN | ... ) ; ; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL | ; STATUS_NOLANGUAGE ; STATUS_FAILED ; STATUS_NOTSUPPORTED ; ; $($R1): Option List ; $($R2): Option Text List ;------------------------------------------------------------------------ [ReturnOptions] ; ; set Status = STATUS_FAILED set OptionList = {} set OptionTextList = {} ; ; Check if the language requested is supported ; set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) in $(LanguageList) ; ; Check if the platforms requested is supported ; ifstr(i) $($1) == "" goto returnoptions endif set PlatformList = ^(PlatformsSupported, 1) Ifcontains(i) $($1) in $(PlatformList) goto returnoptions else set Status = STATUS_NOTSUPPORTED goto finish_ReturnOptions endif else set Status = STATUS_NOLANGUAGE goto finish_ReturnOptions endif ; ; form a list of all the options and another of the text representing ; returnoptions = + set OptionList = ^(Options, 1) set OptionTextList = ^(OptionsText$($0), 1) set Status = STATUS_SUCCESSFUL finish_ReturnOptions = + Return $(Status) $(OptionList) $(OptionTextList) ;------------------------------------------------------------------------ ; ; InstallOption: ; ; This section is shelled to by main installation processing ; or by NCPASHEL.INF during reconfig, removal, update, etc. ; ; ; FUNCTION: To copy files representing Options ; To configure the installed option ; To update the registry for the installed option ; ; INPUT: $($0): Language to use ; $($1): OptionID to install ; $($2): SourceDirectory ; $($3): AddCopy (YES | NO) ; $($4): DoCopy (YES | NO) ; $($5): DoConfig (YES | NO) ; ; OUTPUT: $($R0): STATUS: STATUS_SUCCESSFUL | ; STATUS_NOLANGUAGE | ; STATUS_USERCANCEL | ; STATUS_FAILED ; ;------------------------------------------------------------------------ [InstallOption] ; ; Set default values for ; set Status = STATUS_FAILED ; ; extract parameters ; set Option = $($1) set SrcDir = $($2) set AddCopy = $($3) set DoCopy = $($4) set DoConfig = $($5) Set !DebugOutputControl = 1 ; ; Check if the language requested is supported ; set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) NOT-IN $(LanguageList) Return STATUS_NOLANGUAGE endif set-subst LF = "\n" read-syms GeneralConstants read-syms AllFileConstants read-syms FileConstants"-"$(Option) read-syms DialogConstants$(!STF_LANGUAGE)"-"$(Option) ifstr(i) $(!NTN_Origination) == "NCPA" set Continue = $(OK) endif read-syms AllFileConstants$(!STF_LANGUAGE) read-syms FileConstants$(!STF_LANGUAGE)"-"$(Option) detect date set-title $(FunctionTitle) set to = Begin set from = Begin ; ; Assume all is well. ; set CommonStatus = STATUS_SUCCESSFUL EndWait ; ; Set up the operation-mode-based variables and gaily welcome ; the user. If the "install mode" variable is improperly set, ; assume this is a new installation. ; Begin = + Set ActivateDetection = FALSE Ifstr(i) $(!NTN_InstallMode) == deinstall set StartLabel = removeadapter else-Ifstr(i) $(!NTN_InstallMode) == Update set StartLabel = UpgradeSoftware else-Ifstr(i) $(!NTN_InstallMode) == bind set StartLabel = bindingadapter else-Ifstr(i) $(!NTN_InstallMode) == configure ; set ActivateDetection = TRUE set StartLabel = configureadapter ; ; You cannot config the software component ; Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) ;Debug-Output "Cannot configure the software." Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif set Error = $($R0) set from = end set to = end goto nonfatalinfo endif else ; set ActivateDetection = TRUE set StartLabel = installadapter set OEM_ABANDON_OPTIONS = {} set OEM_ABANDON_SOFTWARE = FALSE set OEM_ABANDON_ON = TRUE endif ; Set the Default values set MemoryAddrValue = *($(MemoryAddrList), $(DEFAULT_MEMORY)) ; Memory Address = 0x55B84000 set IOBaseAddrValue = *($(IOBaseAddrList), $(DEFAULT_IO)) ; IOBase Address = Default set IRQValue = *($(IRQList), $(DEFAULT_IRQ)) ; IRQ Level = Default set InterruptStyleValue = *($(InterruptStyleList), 1) ; InterruptStyle = Auto Detect set LineConfigValue = *($(LineConfigList), 1) ; LineConfig = Auto Detect set SocketValue = *($(SocketList), 1) ; Socket = Auto Detect set InitDelayValue = *($(InitDelayList), 1) ; InitDelay = 0 set NegotiationValue = "ON" ; Negotiation = on set LinkIntegrityValue = "ON" ; Link Integrity = Enabled set CableDetectValue = "ON" ; Cable(Energy) Detect = Enabled set AutoPolarityValue = "ON" ; Auto Polarity = Enabled set MemoryModeValue = "OFF" ; Memory Mode = off set DynamicLinkDetectValue = "ON" ; Dynamic Link Detection = on set NetworkAddressValue = "" ; Not used when Blank set TxBufferSizeValue = 10 ; Not shown on Dialog Box set RxBufferSizeValue = 30 ; Not shown on Dialog Box Set from = $(fatal) Set to = $(fatal) Goto $(StartLabel) ;----------------------------------------------- ; Installation Section ;----------------------------------------------- installadapter = + ; ; First, check whether the same version of the software exists ; OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) ; ; Same version already existed in the local machine ; Popup the dialog and ask the user whether he wants to continue ; CloseRegKey $(KeyProduct) ifstr(i) !(NTN_RegBase) == $(ProductKeyName) ; ; Cannot Install the same software again ; Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+ $(ProductVersion) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif goto end else ; ; Add a new adapter card? ; Shell $(UtilityInf), CardExistedDlg ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif ifstr(i) $($R1) != "OK" goto end endif set OldVersionExisted = $(TRUE) endif endif ; ; dll load addition ; Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) install "Install-Dll" goto adaptersetup ;----------------------------------------------- ; Configuration Section ;----------------------------------------------- ; ; Get the current values of all the parameters ; configureadapter = + Ifstr $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component product key" goto fatalregistry Endif Endif ; ; Get the other parameters; they're attached to the service parameters key ; Debug-Output "INF: Shelling to FindService" Shell $(UtilityInf) FindService, $(KeyProduct) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "INF: FindService shell failure" Goto ShellCodeError Endif Ifstr(i) $($R0) != NO_ERROR Debug-Output "INF: FindService Shell error: "$($R0) Goto fatalregistry endif Set KeyParameters = $($R2) ; ; We don't need the services key, so close it. ; CloseRegKey $($R1) Ifstr $(KeyParameters) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE Debug-Output "Cannot find component service" goto fatalregistry endif set OldVersionExisted = $(TRUE) set ValueName = "" set ValueData = "" set ValueStr = "" set ValueList = {} ; ; Get the old values from the Registry [Get Values] ; ********************************************************* EnumRegValue $(KeyParameters) ValueList ForListDo $(ValueList) set ValueItem = $($) set ValueName = *($(ValueItem),1) set ValueData = *($(ValueItem),4) ifstr(i) $(ValueName) == "MemoryBaseAddress" set MemoryAddrIndex = $(ValueData) else-ifstr(i) $(ValueName) == "IoBaseAddress" set IOBaseAddrIndex = $(ValueData) else-ifstr(i) $(ValueName) == "InterruptNumber" set IRQValueIndex = $(ValueData) else-ifstr(i) $(ValueName) == "InterruptStyle" set InterruptStyleIndex = $(ValueData) else-ifstr(i) $(ValueName) == "LineConfig" set LineConfigIndex = $(ValueData) else-ifstr(i) $(ValueName) == "SocketNumber" set SocketIndex = $(ValueData) else-ifstr(i) $(ValueName) == "InitDelay" set InitDelayIndex = $(ValueData) else-ifstr(i) $(ValueName) == "Negotiation" set NegotiationValue = $(ValueData) else-ifstr(i) $(ValueName) == "LinkIntegrity" set LinkIntegrityValue = $(ValueData) else-ifstr(i) $(ValueName) == "CableDetect" set CableDetectValue = $(ValueData) else-ifstr(i) $(ValueName) == "AutoPolarity" set AutoPolarityValue = $(ValueData) else-ifstr(i) $(ValueName) == "MemoryMode" set MemoryModeValue = $(ValueData) else-ifstr(i) $(ValueName) == "DynamicLinkDetect" set DynamicLinkDetectValue = $(ValueData) else-ifstr(i) $(ValueName) == "NetworkAddress" set NetworkAddressValue = $(ValueData) else-ifstr(i) $(ValueName) == "TxBufferSize" set TxBufferSizeValue = $(ValueData) else-ifstr(i) $(ValueName) == "RxBufferSize" set RxBufferSizeValue = $(ValueData) endif EndForListDo set MemoryAddrValue = *($(MemoryAddrList), ~($(MemoryAddrValues),$(MemoryAddrIndex))) ifstr(i) $(MemoryAddrValue) == "" set MemoryAddrValue = *($(MemoryAddrValues), $(DEFAULT_MEMORY)) endif set IOBaseAddrValue = *($(IOBaseAddrList), ~($(IOBaseAddrValues),$(IOBaseAddrIndex))) ifstr(i) $(IOBaseAddrValue) == "" set IOBaseAddrValue = *($(IOBaseAddrList), $(DEFAULT_IO)) endif set IRQValue = *($(IRQList), ~($(IRQValues),$(IRQValueIndex))) ifstr(i) $(IRQValue) == "" set IRQValue = *($(IRQList), $(DEFAULT_IRQ)) endif set InterruptStyleValue = *($(InterruptStyleList), ~($(InterruptStyleValues),$(InterruptStyleIndex))) ifstr(i) $(InterruptStyleValue) == "" set InterruptStyleValue = *($(InterruptStyleList), 0) endif set LineConfigValue = *($(LineConfigList), ~($(LineConfigValues),$(LineConfigIndex))) ifstr(i) $(LineConfigValue) == "" set LineConfigValue = *($(LineConfigValues), 1) endif set SocketValue = *($(SocketList), ~($(SocketValues),$(SocketIndex))) ifstr(i) $(SocketValue) == "" set SocketValue = *($(SocketValues), 1) endif set InitDelayValue = *($(InitDelayList), ~($(InitDelayValues),$(InitDelayIndex))) ifstr(i) $(InitDelayValue) == "" set InitDelayValue = *($(InitDelayValues), 1) endif ifstr(i) $(NegotiationValue) == "" set NegotiationValue = 1 endif ifstr(i) $(LinkIntegrityValue) == "" set LinkIntegrityValue = 1 endif ifstr(i) $(CableDetectValue) == "" set CableDetectValue = 1 endif ifstr(i) $(AutoPolarityValue) == "" set AutoPolarityValue = 1 endif ifstr(i) $(MemoryModeValue) == "" set MemoryModeValue = 0 endif ifstr(i) $(DynamicLinkDetectValue) == "" set DynamicLinkDetectValue = 1 endif ifint $(NegotiationValue) == 1 set NegotiationValue = "ON" else set NegotiationValue = "OFF" endif ifint $(LinkIntegrityValue) == 1 set LinkIntegrityValue = "ON" else set LinkIntegrityValue = "OFF" endif ifint $(CableDetectValue) == 1 set CableDetectValue = "ON" else set CableDetectValue = "OFF" endif ifint $(AutoPolarityValue) == 1 set AutoPolarityValue = "ON" else set AutoPolarityValue = "OFF" endif ifint $(MemoryModeValue) == 1 set MemoryModeValue = "ON" else set MemoryModeValue = "OFF" endif ifint $(DynamicLinkDetectValue) == 1 set DynamicLinkDetectValue = "ON" else set DynamicLinkDetectValue = "OFF" endif set CheckItemsIn = {$(NegotiationStr),$(LinkIntegrityStr),$(CableDetectStr),+ $(AutoPolarityStr),$(MemoryModeStr),$(DynamicLinkDetectStr)} ;set CheckItemsIn = {"OFF", "ON", "OFF"} ; Save the settings as they were read from the Registry. ; Shell $(ParamInf) Param_SaveValues ; Set CurrParamSettings = $($R0) ; ; Put up the adapter configuration dialog if necessary. ; ; Note that $(CurrParamSettings) has the old known parameter values. ; adaptersetup = + ;Shell "" DebugConfiguration "before displaying dialog" Set from = adapteroptions adapteroptions = + ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" goto skipoptions endif set CheckItemsIn = {$(NegotiationStr),$(LinkIntegrityStr),$(CableDetectStr),+ $(AutoPolarityStr),$(MemoryModeStr),$(DynamicLinkDetectStr)} LoadLibrary "disk 1" $(DialogDllName) hLib read-syms FileDependentDlg$(!STF_LANGUAGE)"-"$(Option) set ENABLER = 0 ;------------------------------------------------------ ui start "InputDlg" $(hLib) set ExitButton = $(ButtonPressed) FreeLibrary $(hLib) ifstr(i) $(DLGEVENT) == "CONTINUE" set MemoryAddrIndex = $(Combo1Out) set IOBaseAddrIndex = $(Combo2Out) set IRQValueIndex = $(Combo3Out) set InterruptStyleIndex = $(Combo4Out) set LineConfigIndex = $(Combo5Out) set SocketIndex = $(Combo6Out) set InitDelayIndex = $(Combo7Out) set NegotiationValue = *($(CheckItemsOut), 1) set LinkIntegrityValue = *($(CheckItemsOut), 2) set CableDetectValue = *($(CheckItemsOut), 3) set AutoPolarityValue = *($(CheckItemsOut), 4) set MemoryModeValue = *($(CheckItemsOut), 5) set DynamicLinkDetectValue = *($(CheckItemsOut), 6) set NetworkAddressValue = *($(EditTextOut), 1) set TxBufferSizeValue = *($(EditTextOut), 2) set RxBufferSizeValue = *($(EditTextOut), 3) set ExitButton = $(ButtonPressed) ui pop 1 else-ifstr(i) $(DLGEVENT) == "EXIT" set CommonStatus = STATUS_USERCANCEL ui pop 1 goto end else set CommonStatus = STATUS_USERCANCEL ui pop 1 Debug-Output "Action: unknown. Bye." goto end endif ; ; If installing, go create the necessary keys; ; if configuring, they're already open. ; skipoptions =+ ifint $(OldVersionExisted) == $(TRUE) ifstr(i) $(!NTN_InstallMode) == configure goto writeparameters endif endif StartWait ; ; Add Software Component ; ifint $(OldVersionExisted) == $(FALSE) ifstr(i) $(!NTN_InstallMode) == "install" Ifstr(i) $(DoCopy) == "YES" Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) Endif install "Install-Option" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal endif endif Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), + $(ProductSoftwareName), + $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), + $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+ $(NetEventDLL) Set OEM_ABANDON_SOFTWARE = TRUE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif ; ; At this point: ; $R1 contains the product version key handle; ; $R2 contains the NetRules subkey handle; ; $R3 contains the new Services key handle; and ; $R4 contains the Parameters key ; $R5 contains the Linkage Key ; set RegistryErrorIndex = $($R0) set KeyProduct = $($R1) Set SoftNetRulesKey = $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add software components" CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+ {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+ {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+ {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add value list." CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+ {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, + {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, + {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Resgitry error: add value list." goto fatalregistry endif endif ; ; Create the HARDWARE\Netcard region and its corresponding service ; Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName) ifint $($R4) != -1 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)) endif ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "Cannot add hardware component" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Registry error: add hardware component" CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) goto fatalregistry endif ; ; At this point: ; $R1 Registry key variable for HARDWARE\Netcard\(n) ; $R2 Registry key variable for HARDWARE\Netcard\(n)\\NetRules ; $R3 Registry key handle for <service>\Parameters key ; $R4 Adapter number assigned to adapter ; $R5 Service name generated by combining svc name with adapter number ; set KeyParameters = $($R3) set KeyAdapterRules = $($R2) set AdapterNumber = $($R4) set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+ {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareDescription)},+ {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $($R1), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif CloseRegKey $($R1) set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)"""" set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm) set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+ {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait Debug-Output "Resgitry error: add value list." CloseRegKey $(KeyParameters) CloseRegKey $(KeyAdapterRules) goto fatalregistry endif CloseRegKey $(KeyAdapterRules) goto writeparameters ; ; REQUIRED: $(KeyParameters) contains service Parameters key handle ; writeparameters = + Shell $(UtilityInf), GetBusTypeNum set BusTypeNum = $($R1) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif ; ; Add the rest of the parameters to the Services area ; ifstr(i) $(NegotiationValue) == "ON" set NegotiationValue = "1" else set NegotiationValue = "0" endif ifstr(i) $(LinkIntegrityValue) == "ON" set LinkIntegrityValue = "1" else set LinkIntegrityValue = "0" endif ifstr(i) $(CableDetectValue) == "ON" set CableDetectValue = "1" else set CableDetectValue = "0" endif ifstr(i) $(AutoPolarityValue) == "ON" set AutoPolarityValue = "1" else set AutoPolarityValue = "0" endif ifstr(i) $(MemoryModeValue) == "ON" set MemoryModeValue = "1" else set MemoryModeValue = "0" endif ifstr(i) $(DynamicLinkDetectValue) == "ON" set DynamicLinkDetectValue = "1" else set DynamicLinkDetectValue = "0" endif ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" set MemoryAddrValue = *($(MemoryAddrValues), $(DEFAULT_MEMORY)) set IOBaseAddrValue = *($(IOBaseAddrValues), $(DEFAULT_IO)) set IRQValue = *($(IRQValues), $(DEFAULT_IRQ)) set InterruptStyleValue = *($(InterruptStyleValues), 1) set LineConfigValue = *($(LineConfigValues), 1) set SocketValue = *($(SocketValues), 1) set InitDelayValue = *($(InitDelayValues), 1) else set MemoryAddrValue = *($(MemoryAddrValues),~($(MemoryAddrList), $(MemoryAddrIndex))) set IOBaseAddrValue = *($(IOBaseAddrValues),~($(IOBaseAddrList), $(IOBaseAddrIndex))) set IRQValue = *($(IRQValues), ~($(IRQList), $(IRQValueIndex))) set InterruptStyleValue = *($(InterruptStyleValues), ~($(InterruptStyleList), $(InterruptStyleIndex))) set LineConfigValue = *($(LineConfigValues),~($(LineConfigList), $(LineConfigIndex))) set SocketValue = *($(SocketValues), ~($(SocketList), $(SocketIndex))) set InitDelayValue = *($(InitDelayValues), ~($(InitDelayList), $(InitDelayIndex))) endif set NewValueList = {{AutoPolarity, $(NoTitle),$(!REG_VT_DWORD),$(AutoPolarityValue)},+ {BusNumber, $(NoTitle),$(!REG_VT_DWORD),0},+ {BusType, $(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+ {CableDetect, $(NoTitle),$(!REG_VT_DWORD),$(CableDetectValue)},+ {DynamicLinkDetect, $(NoTitle),$(!REG_VT_DWORD),$(DynamicLinkDetectValue)},+ {Negotiation, $(NoTitle),$(!REG_VT_DWORD),$(NegotiationValue)},+ {IoBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+ {InitDelay, $(NoTitle),$(!REG_VT_DWORD),$(InitDelayValue)},+ {InterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+ {InterruptStyle, $(NoTitle),$(!REG_VT_DWORD),$(InterruptStyleValue)},+ {LineConfig, $(NoTitle),$(!REG_VT_DWORD),$(LineConfigValue)},+ {LinkIntegrity, $(NoTitle),$(!REG_VT_DWORD),$(LinkIntegrityValue)},+ {MediaType, $(NoTitle),$(!REG_VT_DWORD),1},+ {MemoryBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(MemoryAddrValue)},+ {MemoryMode, $(NoTitle),$(!REG_VT_DWORD),$(MemoryModeValue)},+ {PCIVendorID, $(NoTitle),$(!REG_VT_DWORD),4445},+ {PCMCIA, $(NoTitle),$(!REG_VT_DWORD),0},+ {RXBUFFERSIZE, $(NoTitle),$(!REG_VT_DWORD),$(RxBufferSizeValue)},+ {SocketNumber, $(NoTitle),$(!REG_VT_DWORD),$(SocketValue)},+ {TXBUFFERSIZE, $(NoTitle),$(!REG_VT_DWORD),$(TxBufferSizeValue)},+ {NetworkAddress, $(NoTitle),$(!REG_VT_SZ) ,$(NetworkAddressValue)}+ } Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList) ifstr(i) $(!STF_GUI_UNATTENDED) == "YES" Shell $(UtilityInf), AddDefaultNetCardParameters, $(KeyParameters) endif CloseRegKey $(KeyParameters) ; -------------------------------------------------------------------------------- ; Version 1.0 of the driver requires that PCMCIA.sys be disabled to avoid ; contention problems with the cardbus controller chip. Should be fixed with ; updated PCMCIA.sys due from MS in Dec96 ; -------------------------------------------------------------------------------- ifint $(DISABLEPCMCIASYS) == 1 set PCMCIAKeyName = $(!NTN_ServiceBase)"\Pcmcia" OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIAKeyName) $(MAXIMUM_ALLOWED) PCMCIAKey ; Set the values -------------------------------------------------------------------------------------- SetRegValue $(PCMCIAKey) {Start, 0, $(!REG_VT_DWORD),4} ; '4' disables the driver CloseRegKey $(PCMCIAKey) endif ; -------------------------------------------------------------------------------- ; -------------------------------------------------------------------------------- ; -------------------------------------------------------------------------------- ; Write the parameters to the PCMCIA database section ; This is here for SystemSoft C&SSsupport ; First, do 1st Product (i.e. VERS1Product) ; -------------------------------------------------------------------------------- set PCMCIADatabaseKeyName = $(!NTN_ServiceBase)"\Pcmcia\DataBase" ; set PCMCIADatabaseMfgKeyName = $(PCMCIADatabaseKeyName)"\"$(VERS1Manufacturer) set PCMCIADatabaseMfgKeyName = $(PCMCIADatabaseKeyName)"\Xircom" OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName) $(MAXIMUM_ALLOWED) PCMCIADatabaseKey ifstr $(PCMCIADatabaseKey) == $(NULL) ;Debug-Output "Pcmcia\DataBase not present" else ; PCMCIA.sys is installed and registry has database section in it. ; Try to open Manufacturer section. Delete it if found ; OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName)"\"$(VERS1Manufacturer) $(MAXIMUM_ALLOWED) PCMCIADatabaseMfgKey OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName)"\Xircom" $(MAXIMUM_ALLOWED) PCMCIADatabaseMfgKey ifstr $(PCMCIADatabaseMfgKey) == $(NULL) ; open failed, so create Manufacturer subkey ; CreateRegKey $(PCMCIADatabaseKey) {$(VERS1Manufacturer), 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIADatabaseMfgKey CreateRegKey $(PCMCIADatabaseKey) {"Xircom", 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIADatabaseMfgKey endif ; Open Product Name aka $(VERS1Product) ---------------------------------------------------------------------- OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseMfgKeyName)"\"$(VERS1Product) $(MAXIMUM_ALLOWED) PCMCIADatabaseMfgC56Key ifstr $(PCMCIADatabaseMfgC56Key) == $(NULL) CreateRegKey $(PCMCIADatabaseMfgKey) {$(VERS1Product), 0, 0} "" $(MAXIMUM_ALLOWED) 0 PCMCIADatabaseMfgC56Key endif ; Set the values -------------------------------------------------------------------------------------- SetRegValue $(PCMCIADatabaseMfgC56Key) {Driver, 0, $(!REG_VT_SZ),"CBE"} ; SetRegValue $(PCMCIADatabaseMfgC56Key) {AttributeMemorySize, 0, $(!REG_VT_DWORD),8192} SetRegValue $(PCMCIADatabaseMfgC56Key) {DeviceType, 0, $(!REG_VT_SZ),"NET"} CloseRegKey $(PCMCIADatabaseMfgC56Key) CloseRegKey $(PCMCIADatabaseMfgKey) CloseRegKey $(PCMCIADatabaseKey) endif ; -------------------------------------------------------------------------------- ; Write the parameters to the PCMCIA database section ; This is here for SystemSoft C&SSsupport ; Second, do 2nd Product (i.e. VERS1Product2) ; -------------------------------------------------------------------------------- set PCMCIADatabaseKeyName = $(!NTN_ServiceBase)"\Pcmcia\DataBase" ; set PCMCIADatabaseMfgKeyName = $(PCMCIADatabaseKeyName)"\"$(VERS1Manufacturer) set PCMCIADatabaseMfgKeyName = $(PCMCIADatabaseKeyName)"\Xircom" OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName) $(MAXIMUM_ALLOWED) PCMCIADatabaseKey ifstr $(PCMCIADatabaseKey) == $(NULL) ;Debug-Output "Pcmcia\DataBase not present" else ; PCMCIA.sys is installed and registry has database section in it. ; Try to open Manufacturer section. Delete it if found ; OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName)"\"$(VERS1Manufacturer) $(MAXIMUM_ALLOWED) PCMCIADatabaseMfgKey OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName)"\Xircom" $(MAXIMUM_ALLOWED) PCMCIADatabaseMfgKey ifstr $(PCMCIADatabaseMfgKey) == $(NULL) ; open failed, so create Manufacturer subkey ; CreateRegKey $(PCMCIADatabaseKey) {$(VERS1Manufacturer), 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIADatabaseMfgKey CreateRegKey $(PCMCIADatabaseKey) {"Xircom", 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIADatabaseMfgKey endif ; Open Product Name aka $(VERS1Product2) ---------------------------------------------------------------------- OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseMfgKeyName)"\"$(VERS1Product2) $(MAXIMUM_ALLOWED) PCMCIADatabaseMfgC56Key ifstr $(PCMCIADatabaseMfgC56Key) == $(NULL) CreateRegKey $(PCMCIADatabaseMfgKey) {$(VERS1Product2), 0, 0} "" $(MAXIMUM_ALLOWED) 0 PCMCIADatabaseMfgC56Key endif ; Set the values -------------------------------------------------------------------------------------- SetRegValue $(PCMCIADatabaseMfgC56Key) {Driver, 0, $(!REG_VT_SZ),"CBE"} ; SetRegValue $(PCMCIADatabaseMfgC56Key) {AttributeMemorySize, 0, $(!REG_VT_DWORD),8192} SetRegValue $(PCMCIADatabaseMfgC56Key) {DeviceType, 0, $(!REG_VT_SZ),"NET"} CloseRegKey $(PCMCIADatabaseMfgC56Key) CloseRegKey $(PCMCIADatabaseMfgKey) CloseRegKey $(PCMCIADatabaseKey) endif ; -------------------------------------------------------------------------------- ; Write the parameters to the PCMCIA database section ; This is here for SystemSoft C&SSsupport ; Third, do 3rd Product (i.e. VERS1Product3) ; -------------------------------------------------------------------------------- set PCMCIADatabaseKeyName = $(!NTN_ServiceBase)"\Pcmcia\DataBase" ; set PCMCIADatabaseMfgKeyName = $(PCMCIADatabaseKeyName)"\"$(VERS1Manufacturer) set PCMCIADatabaseMfgKeyName = $(PCMCIADatabaseKeyName)"\Xircom" OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName) $(MAXIMUM_ALLOWED) PCMCIADatabaseKey ifstr $(PCMCIADatabaseKey) == $(NULL) ;Debug-Output "Pcmcia\DataBase not present" else ; PCMCIA.sys is installed and registry has database section in it. ; Try to open Manufacturer section. Delete it if found ; OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName)"\"$(VERS1Manufacturer) $(MAXIMUM_ALLOWED) PCMCIADatabaseMfgKey OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseKeyName)"\Xircom" $(MAXIMUM_ALLOWED) PCMCIADatabaseMfgKey ifstr $(PCMCIADatabaseMfgKey) == $(NULL) ; open failed, so create Manufacturer subkey ; CreateRegKey $(PCMCIADatabaseKey) {$(VERS1Manufacturer), 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIADatabaseMfgKey CreateRegKey $(PCMCIADatabaseKey) {"Xircom", 0, 0} "" $(MAXIMUM_ALLOWED) "" PCMCIADatabaseMfgKey endif ; Open Product Name (i.e. VERS1Product3) ---------------------------------------------------------------------- OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIADatabaseMfgKeyName)"\"$(VERS1Product3) $(MAXIMUM_ALLOWED) PCMCIADatabaseMfgC56Key ifstr $(PCMCIADatabaseMfgC56Key) == $(NULL) CreateRegKey $(PCMCIADatabaseMfgKey) {$(VERS1Product3), 0, 0} "" $(MAXIMUM_ALLOWED) 0 PCMCIADatabaseMfgC56Key endif ; Set the values -------------------------------------------------------------------------------------- SetRegValue $(PCMCIADatabaseMfgC56Key) {Driver, 0, $(!REG_VT_SZ),"CBE"} ; SetRegValue $(PCMCIADatabaseMfgC56Key) {AttributeMemorySize, 0, $(!REG_VT_DWORD),8192} SetRegValue $(PCMCIADatabaseMfgC56Key) {DeviceType, 0, $(!REG_VT_SZ),"NET"} CloseRegKey $(PCMCIADatabaseMfgC56Key) CloseRegKey $(PCMCIADatabaseMfgKey) CloseRegKey $(PCMCIADatabaseKey) endif ; -------------------------------------------------------------------------------- ; -------------------------------------------------------------------------------- ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error." goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR Debug-Output "Registry error: Add value list" goto fatalregistry endif EndWait goto successful ;----------------------------------------------- ; Binding section ;----------------------------------------------- bindingadapter =+ set Error = "Binding: Sorry, not yet implemented." goto fatal ;----------------------------------------------- ; Removeadapter section ;----------------------------------------------- removeadapter = + Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) ; Remove Software Component Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif else Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $(!NTN_RegBase) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif ;----------------------------------------------- ; Remove Manufacturer Key ;----------------------------------------------- OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_SoftwareBase) $(MAXIMUM_ALLOWED) KeyManf Ifstr $(KeyManf) == $(KeyNull) Debug-Output "INF: Could not open HKLM\SOFTWARE registry key" else DeleteRegKey $(KeyManf) $(Manufacturer) Ifint $(RegLastError) != $(!REG_ERROR_SUCCESS) Debug-Output "INF: Could not delete Manufacturer registry key" else Debug-Output "INF: Deleted Manufacturer registry key" Endif CloseRegKey $(KeyManf) endif ;----------------------------------------------- ; From version 1.0 of the driver, re-enable the PCMCIA.sys driver ; when removing this adapter from the system. ;----------------------------------------------- ifint $(DISABLEPCMCIASYS) == 1 set PCMCIAKeyName = $(!NTN_ServiceBase)"\Pcmcia" OpenRegKey $(!REG_H_LOCAL) "" $(PCMCIAKeyName) $(MAXIMUM_ALLOWED) PCMCIAKey ; Set the values -------------------------------------------------------------------------------------- SetRegValue $(PCMCIAKey) {Start, 0, $(!REG_VT_DWORD),0} ; '0' restores the driver to "BOOT" CloseRegKey $(PCMCIAKey) endif goto end ;----------------------------------------------- ; Upgrade Software section ;----------------------------------------------- UpgradeSoftware = + ; ; First determine whether we want to do upgrade or update for software ; or hardware component. Then we will determine whether the Mode is ; update or upgrade. ; ; If the same version of the product existed in the registry, we do ; update. Otherwise, we will do a upgrade ; ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) ; Upgrade software component ; ; see whether the same version exist or not ; OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) GetRegValue $(KeyProduct),"MajorVersion", VersionInfo set Version = *($(VersionInfo), 4) ; ; Update the binaries ; Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set !UG_Filename = $($R0) ifstr(i) $(!UG_Filename) != "" install "Install-Update" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS goto fatal endif endif ; Upgrade the version number ; SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)} SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)} ; ; do nothing for update ; ifint $(Version) != $(ProductVersion) ; ; If the major version number is not the same, ; it is major upgrade. So let Upgrade the product ; ; ; make other upgrade change if necessary ; endif CloseRegKey $(KeyProduct) else ; ; Cannot Open software key, goto ERROR ; goto fatalregistry endif else ; ; upgrade/update hardware component ; There is no different between upgrade and update for hardware ; component ; ; 1. Get the Service Name ; 2. Change the NetRule section if necessary ; OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) + $(MAXIMUM_ALLOWED) NetworkCardKey Ifstr(i) $(NetworkCardKey) != $(KeyNull) ; ; Get Service name ; GetRegValue $(NetworkCardKey),"ServiceName", ServiceNameInfo set ServiceName = *($(ServiceNameInfo), 4) ; ; Change the NetRule if necessary ; OpenRegKey $(NetworkCardKey) "" "NetRules" + $(MAXIMUM_ALLOWED) NetRuleKey Ifstr(i) $(NetRuleKey) != $(KeyNull) ; ; Make the change.... ; else ; ; Error, cannot open net rules key ; goto fatalregistry endif CloseRegKey $(NetRules) CloseRegKey $(NetworkCardKey) else ; ; Error, cannot open network card key ; goto fatalregistry endif ; ; 3. Change the service section of the hardware. i.e., ; ParameterName change, value change, etc. ; OpenRegKey $(!REG_H_LOCAL) "" + $(!NTN_ServiceBase)"\"$(ServiceName) + $(MAXIMUM_ALLOWED) ServiceKey Ifstr(i) $(ServiceKey) != $(KeyNull) ; ; Get the ServiceKey to change the Start value ; or Type value. Or open Parameters key to ; change the hardware parameters if necessary. ; CloseRegKey $(ServiceKey) else ; ; Error, cannot open network card key ; goto fatalregistry endif endif goto end ; ; End of Upgrade Software ; ; ; Escape hatches ; successful = + goto end abandon = + ForListDo $(OEM_ABANDON_OPTIONS) Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $($) ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif EndForListDo Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE ; Remove Software Component Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), FALSE ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error" goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end ; ; warning display ; warning = + Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(to) else-ifstr(i) $($R1) == "CANCEL" goto $(from) else goto "end" endif ; ; non fatal error display ; nonfatalinfo = + Set Severity = STATUS Set CommonStatus = STATUS_USERCANCEL goto nonfatalmsg nonfatal = + Set Severity = NONFATAL goto nonfatalmsg nonfatalmsg = + ifstr(i) $(Error) == "" Set Severity = NONFATAL Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(from) else goto "end" endif ; ; Registry is broken ; fatalregistry = + Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal ; ; Netcard detection failure ; fataldetect = + Shell $(UtilityInf),RegistryErrorString,CANNOT_DETECT ifint $($ShellCode) != $(!SHELL_CODE_OK) Debug-Output "ShellCode error: cannot get an error string." goto ShellCodeError endif set Error = $($R0) Goto fatal ; ; fatal error display ; fatal = + ifstr(i) $(Error) == "" Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto setfailed ; ; Shelling error ; ShellCodeError = + set DlgType = "MessageBox" set STF_MB_TITLE = $(ShellCodeErrorTitle) set STF_MB_TEXT = $(ShellCodeErrorText) set STF_MB_TYPE = 1 set STF_MB_ICON = 3 set STF_MB_DEF = 1 ui start "Error Message" goto setfailed setfailed = + set CommonStatus = STATUS_FAILED ; ; if OEM_ABANDON_ON == TRUE, then remove the registry entries ; ifstr(i) $(OEM_ABANDON_ON) == TRUE set OEM_ABANDON_ON = FALSE goto abandon endif goto end end = + goto term term = + Return $(CommonStatus) [DebugConfiguration] Set InfName = "OEMSETNT.INF" ;Debug-Output $(InfName)" **CONFIGURATION STATE: "$($0) ;Debug-Output $(InfName)" IRQ_Level is "$(!p:IRQ_Level) ;Debug-Output $(InfName)" IOBaseAddrValue is "$(!p:IOBaseAddrValue) ;Debug-Output $(InfName)" TransceiverValue is "$(!p:TransceiverValue) ;Debug-Output $(InfName)" MemoryAddr is "$(!p:MemoryAddr) ;Debug-Output $(InfName)" MappedValue is "$(!p:MappedValue) return ;*************************************************************** ; INSTALL SECTIONS ;*************************************************************** [Install-Option] set STF_VITAL = "" ifstr(i) $(AddCopy) == "YES" AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers endif ifstr(i) $(DoCopy) == "YES" ; ; Copy files in the copy list ; set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList endif Exit [Install-Update] set STF_VITAL = "" set STF_OVERWRITE = "VERIFYSOURCEOLDER" ;set STF_VERSION = "YES" AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exit [Install-Dll] set STF_VITAL = "" AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH) set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exit [Source Media Descriptions] 1 = "Xircom Setup Disk for NT" [ProductType] STF_PRODUCT = Winnt STF_PLATFORM = I386 [Files-Inf] 1, OEMSETNT.INF, SIZE=58000, RENAME=$(!UG_Filename) [Files-Dll] 1, CBE.DLL, SIZE=21000 [Files-CBE] 1, CBEN4.SYS, SIZE=53000 [LanguagesSupported] ENG [AllFileConstantsENG] ProCaption = "Windows NT Setup" ProCancel = "Cancel" ProCancelMsg = "Windows NT Networking is not correctly installed. "+ "Are you sure you want to cancel copying files?" ProCancelCap = "Network Setup Message" ProText1 = "Copying:" ProText2 = "To:" DialogDllName = "CBE.DLL" ; START CBE ------------------------------------------------------------------------------------------- [FileConstantsENG-CBE] FunctionTitle = $(GenericAdapterName)" Setup"$(GenericInfVersion) ProductSoftwareTitle = $(GenericDriverName) ProductHardwareTitle = $(GenericAdapterName) MemoryAddrList = ^(MemoryAddrChoices,1) MemoryAddrValues = ^(MemoryAddrChoices,2) IOBaseAddrList = ^(IOBaseAddrChoices, 1) IOBaseAddrValues = ^(IOBaseAddrChoices, 2) IRQList = ^(IRQChoices, 1) IRQValues = ^(IRQChoices, 2) InterruptStyleList = ^(InterruptStyleChoices, 1) InterruptStyleValues = ^(InterruptStyleChoices, 2) LineConfigList = ^(LineConfigChoices, 1) LineConfigValues = ^(LineConfigChoices, 2) SocketList = ^(SocketChoices, 1) SocketValues = ^(SocketChoices, 2) InitDelayList = ^(InitDelayChoices, 1) InitDelayValues = ^(InitDelayChoices, 2) [DialogConstantsENG-CBE] Help = "&Help" Exit = "Cancel" OK = "OK" HelpContext = "" Continue = "Continue" Cancel = "Cancel" [FileDependentDlgENG-CBE] DlgType = "RadioCombination" DlgTemplate = "CBE" Caption = $(FunctionTitle) HelpContext = $(!IDH_DB_OEMNADE2_INS) CBOptionsGreyed = {} NotifyFields = {NO, NO, NO, NO, NO, NO, NO, NO} Combo1Label = "Memory Address:" Combo2Label = "I/O Port:" Combo3Label = "Interrupt:" Combo4Label = "Interrupt Style:" Combo5Label = "Line Configuration:" Combo6Label = "PCCard Socket:" Combo7Label = "Initialization Delay:" Check1 = "Line &Negotiation" Check2 = "Link &Integrity" Check3 = "Cable &Detect" Check4 = "Auto &Polarity" Check5 = "&Memory Mode" Check6 = "Dynamic &Link Detect" Edit1Label = "Network Address" Edit2Label = "Tx Buffer Size" Edit3Label = "Rx Buffer Size" Combo1List = $(MemoryAddrList) Combo1Out = $(MemoryAddrValue) Combo2List = $(IOBaseAddrList) Combo2Out = $(IOBaseAddrValue) Combo3List = $(IRQList) Combo3Out = $(IRQValue) Combo4List = $(InterruptStyleList) Combo4Out = $(InterruptStyleValue) Combo5List = $(LineConfigList) Combo5Out = $(LineConfigValue) Combo6List = $(SocketList) Combo6Out = $(SocketValue) Combo7List = $(InitDelayList) Combo7Out = $(InitDelayValue) ComboListItemsIn = {Combo1List,Combo2List,Combo3List, Combo4List, Combo5List, Combo6List, Combo7List} ComboListItemsOut = {Combo1Out, Combo2Out, Combo3Out, Combo4Out, Combo5Out, Combo6Out, Combo7Out} CheckItemsIn = {$(NegotiationValue),$(LinkIntegrityValue),$(CableDetectValue),+ $(AutoPolarityValue),$(MemoryModeValue),$(DynamicLinkDetectValue)} CheckItemsOut = {Check1Out, Check2Out, Check3Out, Check4Out, Check5Out, Check6Out} EditTextIn = {$(NetworkAddressValue), $(TxBufferSizeValue), $(RxBufferSizeValue)} EditTextLim = {"","",""} EditTextOut = {Edit1Out, Edit2Out, Edit3Out} ; END CBE ------------------------------------------------------------------------------------------- [MemoryAddrChoices] MA_1 = "0xC0000", 786432 MA_2 = "0xC4000", 802816 MA_3 = "0xC8000", 819200 MA_4 = "0xCC000", 835584 MA_5 = "0xD0000", 851968 MA_6 = "0xD4000", 868352 MA_7 = "0xD8000", 884736 MA_8 = "0xDC000", 901120 MA_9 = "0xE0000", 917504 MA_10 = "0xE4000", 933888 MA_11 = "0xE8000", 950272 MA_12 = "0xEC000", 966656 MA_13 = "0x5B80000", 95944704 MA_14 = "0x5B84000", 95961088 MA_15 = "0x5B88000", 95977472 MA_16 = "0x5B8C000", 95993856 MA_17 = "0x10000000", 268435456 MA_18 = "0x10004000", 268451840 MA_19 = "0x10008000", 268468224 MA_20 = "0x1000C000", 268484608 MA_21 = "0x50000000", 1342177280 MA_22 = "0x50004000", 1342193664 MA_23 = "0x50008000", 1342210048 MA_24 = "0x5000C000", 1342226432 MA_25 = "0x55B80000", 1438121984 MA_26 = "0x55B84000", 1438138368 MA_27 = "0x55B88000", 1438154752 MA_28 = "0x55B8C000", 1438171136 MA_29 = "0xB0000000", 2952790016 MA_30 = "0xB0004000", 2952806400 MA_31 = "0xB0008000", 2952822784 MA_32 = "0xB000C000", 2952839168 [IRQChoices] IRQ_1 = "3", 3 IRQ_2 = "4", 4 IRQ_3 = "5", 5 IRQ_4 = "7", 7 IRQ_5 = "9", 9 IRQ_6 = "10", 10 IRQ_7 = "11", 11 IRQ_8 = "12", 12 IRQ_9 = "13", 13 IRQ_10 = "14", 14 IRQ_11 = "15", 15 [SocketChoices] S_0 = "Auto Detect",0 S_1 = "1",1 S_2 = "2",2 S_3 = "3",3 S_4 = "4",4 [InterruptStyleChoices] IS_1 = "Auto Detect", 0 IS_2 = "PCI IRQ", 1 IS_3 = "ISA IRQ", 2 [LineConfigChoices] LC_1 = "Auto Detect", 0 LC_2 = "10 Mbps/Half Duplex", 1 LC_3 = "10 Mbps/Full Duplex", 2 LC_4 = "100 Mbps/Half Duplex", 3 LC_5 = "100 Mbps/Full Duplex", 4 [IOBaseAddrChoices] IOBase_1 = "0x1000",4096 IOBase_2 = "0x1800",6144 IOBase_3 = "0x2000",8192 IOBase_4 = "0x2800",10240 IOBase_5 = "0x3000",12288 IOBase_6 = "0x3800",14336 IOBase_7 = "0x4000",16384 IOBase_8 = "0x4800",18432 IOBase_9 = "0x5000",20480 IOBase_10 = "0x5800",22528 IOBase_11 = "0x6000",24576 IOBase_12 = "0x6800",26624 IOBase_13 = "0x7000",28672 IOBase_14 = "0x7800",30720 IOBase_15 = "0x8000",32768 IOBase_16 = "0x8800",34816 IOBase_17 = "0x9000",36864 IOBase_18 = "0x9800",38912 IOBase_19 = "0xA000",40960 IOBase_20 = "0xA800",43008 IOBase_21 = "0xB000",45056 IOBase_22 = "0xB800",47104 IOBase_23 = "0xC000",49152 IOBase_24 = "0xC800",51200 IOBase_25 = "0xD000",53248 IOBase_26 = "0xD800",55296 IOBase_27 = "0xE000",57344 IOBase_28 = "0xE800",59392 IOBase_29 = "0xF000",61440 IOBase_30 = "0xF500",62720 IOBase_31 = "0xF800",63488 [InitDelayChoices] InitD_0 = "0",0 InitD_1 = "1",1 InitD_2 = "2",2 InitD_3 = "3",3 InitD_4 = "4",4 InitD_5 = "5",5 InitD_6 = "10",10 InitD_7 = "20",20 InitD_8 = "30",30 InitD_9 = "40",40 InitD_10 = "50",50 InitD_11 = "60",60Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.