#Generated by UJ Circuit AnalyzerMonday, August 11, 2003 - 1:03:28 AM # Modified by Ron Lisle 8/15/03 to correct BiosAddress and EAPD. # StacSrv version 4152 # Driver version 4152 # 08/20/03 RJL manual edit - swapped Jacks 1<->2, 3<->4. # 08/25/03 RJL Add PolicyHPMuteSpkrs # 11/20/03 RJL Added MicBiasChargeDelay to front jacks, 30 seconds (starting point). # # 12/02/03 RJL Phase 2 changes: # Jack Pins Loc Color Mic Default Desc # ---- ----- ----- ----- --- -------- --------------- # 1 35/36 Front Green 0 Auto Mic & HP & Line-Out # 2 39/41 Front Pink 2 Auto Mic & HP # 3 23/24 Rear Blue 1 Surround LineIn or Surround or Mic # 4 35/36 Rear Green 0 Off Mic & HP & Line-Out (=J1) # 5 43/44 Rear Pink 3 C/LFE Mic or CLFE # 6 21/22 Int - Line-Out Disabled by HP # # All jacks except Int utilize GpioX jack switch. [Models] ;all MODEL files (except perhaps STAC97.ini) should have a self-reference here. ;self-reference: #MANUAL EDIT: Change ID number to proper value PCI\VEN_8086&DEV_24D5&subsys_2017107B= this [DelRegKeys] # Specify the registry keys to be deleted during Uninstall HKCU\Software\Sigmatel\Settings=Yes ; Delete the current user's settings subkey HKCU\Software\Sigmatel\JackSense=Yes ; Delete the current user's jacksense subkey HKCU\Software\Sigmatel\JackSense2=Yes ; Delete new user key HKLM\Software\Sigmatel\JackSense2=Yes ; both of them HKR\Settings=Yes ; Delete the driver's settings subkey HKR\JackSense=Yes ; Delete the driver's jacksense subkey # The following 2 keys cause the volume settings to be 'forgotten' during Uninstall HKCU\Software\Microsoft\Windows\CurrentVersion\Applets\Volume Control\SigmaTel Audio=Yes HKU\Software\Microsoft\Windows\CurrentVersion\Applets\Volume Control\SigmaTel Audio=Yes [Apps] # Specify the application software to install TinyUJ2 = No SSWiz = YesInvisible StacSysTrayHidden = YesInvisible StacIt = YesInvisible PassThru= YesInvisible # The following keys are used by StacSrv.application [HKLM\Software\SigmaTel\Jacksense2] RegistryVersionNum = dword: 0x1 ; Newer registry format based on jacks, not pins ;Mode = dword: 0x0 ; Reserved. Leave 0 DefaultSpeakerConfig = dword: 0x0004 ; Default MS Spkr Config set by StacApp PollingPeriod = dword: 333 ; 333 millliseconds JSOscFreq = dword: 16000 ; Set jacksense oscillator frequency to 16kHz #----------------------------------------------------------------------------------------- # NOTE: manually removed. There is no dock 2nd codec on p865g #DockSupport = dword: 1 ; Bios Interface dock support (none on p865g) #----------------------------------------------------------------------------------------- PolicyHPMuteSpkrs = dword: 0x3f ; Plugging in headphones mutes any speaker output # Specify whether to route Line-Out/Front directly from Dac A or from the Analog Mixer # The JackSense registry key “DigitalModel” should always be specified and set to Dword:1 # in harmony w/ the driver setting EmulateAllMasters (binary) 01 DisableAnalogMixer = dword: 1 ; 1 = Dac A, 0 = mixer # The following keys specify the number of different setups displayed # by the Jack Sharing applet, and the mode that they support. This will # subsequently effect the menu item displayed by the Jack Sharing applet. # Typically 4 modes used are 2 (Headphones), 4 (Stereo Speakers), 5 (Quad), and 7 (5.1) # 0 = None # 1 = Mono Speaker # 2 = Headphones # 3 = Stereo Speakers (narrow) # 4 = Stereo Speakers (wide) # 5 = Quadraphonic (4 channel) # 6 = Surround (4 channel) # 7 = 5.1 Surround (6 channel) # All other values are invalid NumSpkrSetups = dword: 0x0000 ; The number of setups defined. # The following sections define which pins are connected to jacks # Each pin will have properties associated with it such as the color of the jack, # where it is located, and which mode (front, rear, center/lfe) to select when a # speaker is plugged in and autoconfigure is set. # DefaultSpeakerMode specifies which channels to configure if JackSense is # active and AutoConfigure is set and speakers are plugged into the jack # [HKLM\Software\Sigmatel\JackSense2\Jack1] ; 0: 1 - Front Panel Green Jack JackColor = dword: 5 ; Green JackLocation = dword: 1 ; Front Panel JackPanelOrder = dword: 1 ; # 0 ParentCodecIndex = dword: 0 ; Codec 0 PinIndex = dword: 0 ; Pins35/36 GpioSwitch = dword: 6 ; JackSwitch GPIO = GPIO X JSGpioMuxState = dword: -1 ; No GPIO Crosspoint Mux GpioPolarity = dword: 0 ; Inverted MicBias = dword: 0 ; Mic Bias GPIO = GPIO 0 MicBiasPolarity = dword: 0 ; Open-Drain Output Driver MicBiasChargeDelay = dword: 30000 ; 30 seconds. # SupportedDevices, AutoConfigure, and Notify specify bitmaps of which devices to allow: # 1 = empty jack ; if specified causes autoconfigure to disable when empty # 2 = Microphone # 4 = Powered speakers # 8 = Headphones # 0x10 = Line-In # 0x20 = Rear/Surround speakers # 0x40 = Center/LFE speakers # 0x80 = SPDIF-In to Ring of Jack # 0x100 = SPDIF-Out from Tip of Jack SupportedDevices = dword: 0x007F ; - jsNone - jsMic - jsSpkr - jsHeadphone - jsLineIn - jsSurround - jsCenterLFE Notify = dword: 0x0001 ; - jsNone AutoConfigure = dword: 0x000b ; - jsNone - jsMic - jsHeadphone AutoConfigSupport= dword: 0x000b ; - jsNone - jsMic - jsHeadphone DefaultSpeakerMode = dword: 2 ; jsSpkr (Front) # Set calibration so anything above a HP detects as a Mic HPLo = dword: 100 HPHi = dword: 999 MicLo = dword: 1000 MicHi = dword: 63999 SpkrLo = dword: 64000 SpkrHi = dword: 64001 Jack sense algorith controls JSAlgorithm = dword: 1 ; jsaGood JSReadingsTotal = dword: 30 ; 30 JSReadingsGood = dword: 5 ; 5 # Items directly derived from schematic review DaisyChain = dword: 0 ; Jack closest to Codec OutputCapSize = dword: 3 ; 100 uF 25V Alum DirectConnect = dword: 1 ; True FiveOhmResistorPresent = dword: 0 ; False HasIntelFrontPanelHeader = dword: 0 ; False ImpedanceGtrThan16k = dword: 1 ; True IsDeviceSupported = dword: 0 ; False IsolatedSwitch = dword: -1 ; True LowXtalkBias = dword: 0 ; False NotCrossconnected = dword: 1 ; True SameCapOnBothChannels = dword: 1 ; True # [HKLM\Software\Sigmatel\JackSense2\Jack2] ; 0: 2 - Front Panel Pink Jack JackColor = dword: 10 ; Pink JackLocation = dword: 1 ; Front Panel JackPanelOrder = dword: 2 ; # 1 ParentCodecIndex = dword: 0 ; Codec 0 PinIndex = dword: 1 ; Pins39/41 GpioSwitch = dword: 6 ; JackSwitch GPIO = GPIO X JSGpioMuxState = dword: -1 ; No GPIO Crosspoint Mux GpioPolarity = dword: 0 ; Inverted MicBias = dword: 2 ; Mic Bias GPIO = GPIO 2 MicBiasPolarity = dword: 0 ; Open-Drain Output Driver MicBiasChargeDelay = dword: 30000 ; 30 seconds. # SupportedDevices, AutoConfigure, and Notify specify bitmaps of which devices to allow: # 1 = empty jack ; if specified causes autoconfigure to disable when empty # 2 = Microphone # 4 = Powered speakers # 8 = Headphones # 0x10 = Line-In # 0x20 = Rear/Surround speakers # 0x40 = Center/LFE speakers # 0x80 = SPDIF-In to Ring of Jack # 0x100 = SPDIF-Out from Tip of Jack SupportedDevices = dword: 0x007F ; - jsNone - jsMic - jsSpkr - jsHeadphone - jsLineIn - jsSurround - jsCenterLFE Notify = dword: 0x0001 ; - jsNone AutoConfigure = dword: 0x000B ; - jsNone - jsMic - jsHeadphone AutoConfigSupport= dword: 0x000B ; - jsNone - jsMic - jsHeadphone # Set calibration so anything above a HP detects as a Mic HPLo = dword: 100 HPHi = dword: 999 MicLo = dword: 1000 MicHi = dword: 63999 SpkrLo = dword: 64000 SpkrHi = dword: 64001 Jack sense algorith controls JSAlgorithm = dword: 1 ; jsaGood JSReadingsTotal = dword: 30 ; 30 JSReadingsGood = dword: 5 ; 5 # Items directly derived from schematic review DaisyChain = dword: -1 ; No Daisy Chain OutputCapSize = dword: 3 ; 100 uF 25V Alum DirectConnect = dword: -1 ; True FiveOhmResistorPresent = dword: -1 ; True HasIntelFrontPanelHeader = dword: 0 ; False ImpedanceGtrThan16k = dword: -1 ; True IsDeviceSupported = dword: 0 ; False IsolatedSwitch = dword: -1 ; True LowXtalkBias = dword: 0 ; False NotCrossconnected = dword: -1 ; True SameCapOnBothChannels = dword: -1 ; True # [HKLM\Software\Sigmatel\JackSense2\Jack3] ; 0: 3 - Rear Panel Blue Jack JackColor = dword: 6 ; Blue JackLocation = dword: 0 ; Rear Panel JackPanelOrder = dword: 3 ; # 2 ParentCodecIndex = dword: 0 ; Codec 0 PinIndex = dword: 7 ; Pins23/24 GpioSwitch = dword: 6 ; JackSwitch GPIO = GPIO X JSGpioMuxState = dword: -1 ; No GPIO Crosspoint Mux GpioPolarity = dword: 0 ; Inverted MicBias = dword: 1 ; Mic Bias GPIO = GPIO 1 MicBiasPolarity = dword: 0 ; Open-Drain Output Driver MicBiasChargeDelay = dword: 30000 ; 30 seconds. # SupportedDevices, AutoConfigure, and Notify specify bitmaps of which devices to allow: # 1 = empty jack ; if specified causes autoconfigure to disable when empty # 2 = Microphone # 4 = Powered speakers # 8 = Headphones # 0x10 = Line-In # 0x20 = Rear/Surround speakers # 0x40 = Center/LFE speakers # 0x80 = SPDIF-In to Ring of Jack # 0x100 = SPDIF-Out from Tip of Jack SupportedDevices = dword: 0x0077 ; - jsNone - jsMic - jsSpkr - jsLineIn - jsSurround - jsCenterLFE Notify = dword: 0x0009 ; - jsNone - jsHeadphone AutoConfigure = dword: 0x0000 ; - jsbmAllOff AutoConfigSupport = dword: 0 ; Manually configured DefaultSpeakerMode = dword: 5 ; jsSurround PinConfiguration = dword: 5 ; Surround Jack sense algorith controls JSAlgorithm = dword: 1 ; jsaGood JSReadingsTotal = dword: 30 ; 30 JSReadingsGood = dword: 5 ; 5 # Items directly derived from schematic review DaisyChain = dword: -1 ; No Daisy Chain OutputCapSize = dword: 2 ; 3.3 Ceramic DirectConnect = dword: 1 ; True FiveOhmResistorPresent = dword: 0 ; False HasIntelFrontPanelHeader = dword: 0 ; False ImpedanceGtrThan16k = dword: 1 ; True IsDeviceSupported = dword: 0 ; False IsolatedSwitch = dword: 0 ; False LowXtalkBias = dword: 0 ; False NotCrossconnected = dword: 1 ; True SameCapOnBothChannels = dword: 1 ; True # [HKLM\Software\Sigmatel\JackSense2\Jack4] ; 0: 4 - Rear Panel Green Jack JackColor = dword: 5 ; Green JackLocation = dword: 0 ; Rear Panel JackPanelOrder = dword: 4 ; # 3 ParentCodecIndex = dword: 0 ; Codec 0 PinIndex = dword: 0 ; Pins35/36 GpioSwitch = dword: 6 ; JackSwitch GPIO = GPIO X JSGpioMuxState = dword: -1 ; No GPIO Crosspoint Mux GpioPolarity = dword: 0 ; Inverted MicBias = dword: 0 ; Mic Bias GPIO = GPIO 0 MicBiasPolarity = dword: 0 ; Open-Drain Output Driver MicBiasChargeDelay = dword: 30000 ; 30 seconds. # SupportedDevices, AutoConfigure, and Notify specify bitmaps of which devices to allow: # 1 = empty jack ; if specified causes autoconfigure to disable when empty # 2 = Microphone # 4 = Powered speakers # 8 = Headphones # 0x10 = Line-In # 0x20 = Rear/Surround speakers # 0x40 = Center/LFE speakers # 0x80 = SPDIF-In to Ring of Jack # 0x100 = SPDIF-Out from Tip of Jack SupportedDevices = dword: 0x007F ; - jsNone - jsMic - jsSpkr - jsHeadphone - jsLineIn - jsSurround - jsCenterLFE Notify = dword: 0x0001 ; - jsNone AutoConfigure = dword: 0x0000 ; - jsNone - jsMic - jsSpkr - jsHeadphone AutoConfigSupport = dword: 0 ; Manual configuration DefaultSpeakerMode = dword: 2 ; Front Jack sense algorith controls JSAlgorithm = dword: 1 ; jsaGood JSReadingsTotal = dword: 30 ; 30 JSReadingsGood = dword: 5 ; 5 # Items directly derived from schematic review DaisyChain = dword: 1 ; Jack further from codec OutputCapSize = dword: 3 ; 100 uF 25V Alum DirectConnect = dword: 1 ; True FiveOhmResistorPresent = dword: 0 ; False HasIntelFrontPanelHeader = dword: 0 ; False ImpedanceGtrThan16k = dword: 1 ; True IsDeviceSupported = dword: 0 ; False IsolatedSwitch = dword: 0 ; False LowXtalkBias = dword: 0 ; False NotCrossconnected = dword: 1 ; True SameCapOnBothChannels = dword: 1 ; True # [HKLM\Software\Sigmatel\JackSense2\Jack5] ; 0: 5 - Rear Panel Pink Jack JackColor = dword: 10 ; Pink JackLocation = dword: 0 ; Rear Panel JackPanelOrder = dword: 5 ; # 4 ParentCodecIndex = dword: 0 ; Codec 0 PinIndex = dword: 2 ; Pins43/44 GpioSwitch = dword: 6 ; JackSwitch GPIO = GPIO X JSGpioMuxState = dword: -1 ; No GPIO Crosspoint Mux GpioPolarity = dword: 0 ; Inverted MicBias = dword: 3 ; Mic Bias GPIO = GPIO 3 MicBiasPolarity = dword: 0 ; Open-Drain Output Driver MicBiasChargeDelay = dword: 30000 ; 30 seconds. # SupportedDevices, AutoConfigure, and Notify specify bitmaps of which devices to allow: # 1 = empty jack ; if specified causes autoconfigure to disable when empty # 2 = Microphone # 4 = Powered speakers # 8 = Headphones # 0x10 = Line-In # 0x20 = Rear/Surround speakers # 0x40 = Center/LFE speakers # 0x80 = SPDIF-In to Ring of Jack # 0x100 = SPDIF-Out from Tip of Jack SupportedDevices = dword: 0x0077 ; - jsNone - jsMic - jsSpkr - jsLineIn - jsSurround - jsCenterLFE Notify = dword: 0x0001 ; - jsNone AutoConfigure = dword: 0x0000 ; - jsbmAllOff AutoConfigSupport = dword: 0 ; Manually configured PinConfiguration = dword: 6 ; Rear Jack sense algorith controls JSAlgorithm = dword: 1 ; jsaGood JSReadingsTotal = dword: 30 ; 30 JSReadingsGood = dword: 5 ; 5 # Items directly derived from schematic review DaisyChain = dword: -1 ; No Daisy Chain OutputCapSize = dword: 2 ; 3.3 Ceramic DirectConnect = dword: 1 ; True FiveOhmResistorPresent = dword: -1 ; True HasIntelFrontPanelHeader = dword: 0 ; False ImpedanceGtrThan16k = dword: 1 ; True IsDeviceSupported = dword: 0 ; False IsolatedSwitch = dword: 0 ; False LowXtalkBias = dword: 0 ; False NotCrossconnected = dword: 1 ; True SameCapOnBothChannels = dword: 1 ; True # [HKLM\Software\Sigmatel\JackSense2\Jack6] ; 0: 6 - Internal Amp Black Jack JackColor = dword: 0 ; Black JackLocation = dword: 2 ; Internal Amp JackPanelOrder = dword: 6 ; # 5 ParentCodecIndex = dword: 0 ; Codec 0 PinIndex = dword: 5 ; Pins21/22 GpioSwitch = dword: -1 ; JackSwitch GPIO = gpioUnassociated JSGpioMuxState = dword: -1 ; No GPIO Crosspoint Mux GpioPolarity = dword: 0x1 ; gpioUnassociated MicBias = dword: -1 ; Mic Bias GPIO = gpioUnassociated MicBiasPolarity = dword: 1 ; not used # SupportedDevices, AutoConfigure, and Notify specify bitmaps of which devices to allow: # 1 = empty jack ; if specified causes autoconfigure to disable when empty # 2 = Microphone # 4 = Powered speakers # 8 = Headphones # 0x10 = Line-In # 0x20 = Rear/Surround speakers # 0x40 = Center/LFE speakers # 0x80 = SPDIF-In to Ring of Jack # 0x100 = SPDIF-Out from Tip of Jack SupportedDevices = dword: 0x0004 ; - jsSpkr Notify = dword: 0x0000 ; - jsbmAllOff AutoConfigure = dword: 0x0000 ; - jsbmAllOff AutoConfigSupport = dword: 0 ; Manually configured (not configurable) PinConfiguration = dword: 2 ; jsSpkr Jack sense algorith controls JSAlgorithm = dword: 1 ; jsaGood JSReadingsTotal = dword: 30 ; 30 JSReadingsGood = dword: 5 ; 5 # Items directly derived from schematic review DaisyChain = dword: -1 ; No Daisy Chain OutputCapSize = dword: 2 ; 3.3 Ceramic DirectConnect = dword: 1 ; True FiveOhmResistorPresent = dword: 0 ; False HasIntelFrontPanelHeader = dword: 0 ; False ImpedanceGtrThan16k = dword: 1 ; True IsDeviceSupported = dword: 0 ; False IsolatedSwitch = dword: 0 ; False LowXtalkBias = dword: 0 ; False NotCrossconnected = dword: 1 ; True SameCapOnBothChannels = dword: 1 ; True [HKR\Settings] # The JackSense registry key “DigitalModel” should always be specified and set to Dword:1 # in harmony w/ the driver setting EmulateAllMasters (binary) 01 # unless the DigitalMasterControlsAnalog setting is used EmulateAllMasters = hex: 1 ; Digital scaling of master volume # This will allow to enable required analog sources # and make Master Volume slider to affect them too. ( Needs testing - 07-12-2003) # Can be used along with EmulateAllMasters set to 1 # aDigitalModel must be set to 0 for this to work DigitalMasterControlsAnalog = hex: 0 # EnableLinearVolumes can be used to make the volume curve linear. # This affects all analog controls exposed by the driver. ( Needs testing - 07-12-2003 ) EnableLinearVolumes = hex: 0 ; linear volumes like Sony wants # New last minute keys needed for PA1, need to dynamically support in UJCA MakeCodecsPlayInParallel = hex: 1 DockCOdecID = hex: 2 DisableCDIn = hex: 1 MuteInactiveDac = hex:0 SPDIFSharedPinMuxBIts = DWORD:0x0042 ; pin 23/23 is shared with SPDIF on PA1 # provides BIOS interface physical memory addres on systems that implement Sigmatel BIOS # specification (for example on one model we have HKR BiosInterfaceAddress = dword: 0x4e8) BiosInterfaceAddress = dword: 0xf0000 ; address in physical memory (was 0xfdbf0) BiosInterfaceAddressEnd = dword: 0xfffff ; address in physical memory (was 0xfdbf0) # This section disables sliders in both playback and record panels DisableHeadphone = hex: 1 ; normally disabled DisableLnlvl = hex: 1 ; normally disabled DisableWaveIn2 = hex: 1 ; normally disabled DisablePCBeep = hex: 1 ; normally disabled DisablePhone = hex: 1 ; only enabled if there is an analog connection to modem DisableMonoOut = hex: 1 ; only enabled if there is an analog connection to modem DisableAux = hex: 1 ; normally disabled DisableVideo = hex: 1 ; normally disabled Disable3DControl = hex: 1 ; normally disabled DisableMonoVirtual = hex: 1 ; normally disabled DisableMICSelect = hex: 1 DisableLineInFromPlayback = hex: 1 ; but leaves it at the recording MUX DisableMicFromPlayback = hex: 1 ; but leaves it at the recording MUX DisablePeakmeters = hex: 1 PCMVolumeFixedLevel = hex: 08, 08 ; only meaningful in analog or DigitalMasterControlsAnalog mode ### Manual edit EnableSPDIFIn = hex: 0 ; no SPDIF on Profile #EnableSPDIFIn = hex: 1 ; creates analog source ( Video In volume register ) # This section sets initial volume levels MICBoost = hex: 1 ; normally set to 1 WaveInMux = hex: 00, 00, 00, 00 ; normally Mic MasterControlsAux = hex: 0 ; normally disabled for STAC9758 MasterControlsMono = hex: 0 ; normally disabled for STAC9758 RecMuxMuteAtFloor = hex: 0 ; don't mute rec gain, even at bottom of slider MICSelect = hex: 0 ; Mic1 Or Mic2 # Volume units are represented in fixed point hexadecimal, # in the same units that the OS passes to the driver. # [ADC Gain] [Output volume] [Input Volume] # [Reg 0x1C] [Regs 2,4,6,36,38] [Regs A,C,E,10,12,14,16,18] # +22.5 dB 16.8000h = 0x00168000 max slider # +12 dB = 0C.0000h = 0x000C0000 1/4 slider max slider # +06 dB = 06.0000h = 0x00060000 1/2 slider # 0 dB = 00.0000h = 0x00000000 min slider max slider 1/4 slider # -0.5 dB = FFFF.8000h = 0xFFFF8000 # -1 dB = FFFF.0000h = 0xFFFF0000 # -6 dB = FFFA.0000h = 0xFFFF0000 1/2 slider 1/8 slider # -12 dB = FFFA.0000h = 0xFFFF0000 1/4 slider 1/16 slider # -18 dB = FFFA.0000h = 0xFFFF0000 1/8 slider #-35.5 dB = FFDD.8000h = 0xFFDD8000 min slider # -46 dB = FFD2.0000h = 0xFFD20000 min slider MICAtRecMuxVolume = hex: 63, D0, 13, 00 ; (0-168000) ;MICAtRecMuxVolume = hex: 00, 30, 10, 00 MICVolume = hex: 90, 56, 08, 00 ; (ffdd8000-c0000), (5 bit control). CDVolume = hex: 89, F5, FF, FF ; (ffdd8000-c0000), (5 bit controls). ;CDVolume = hex: 00, F0, E9, FF 3DDepthEnable = hex: 0 ; avoid using 3D if possible PCBeepMute = hex: 1 ; mute pc beep as default PhoneMute = hex: 1 ; mute phone as default CDMute = hex: 1 ; mute CD as default VideoMute = hex: 1 ; mute video as default AuxMute = hex: 1 ; mute aux as default # EnableExtAmpControl should be set to (binary) 00 or, better yet, # excluded from .ini’s for models that implement either SPDIF-in, # or StacSrv control of EAPD during JackSense cycles. This setting, EnableExtAmpControl = hex: 0 ; external amp is controlled by a GPIO or EAPD # Other settings EnableNonPCMOnWin2K = hex: 1 ; Enable AC3 on Win2k EnableSPDIFIn = hex: 1 ; SPDIF in slider will appear in Record panel EnableStereoMic = hex: 0 ; use stereo mic input registers to control mic MultichannelEnabledByUser = hex: 1 ; take the driver out of 2-channel mode EnableNewVolumeControls = hex: 1 ; use 6-channel volume button instead of balance control - applies only to master volume DisableSubwooferAtMono = hex:1 ; RJL 12/04/03 # These settings control the values loaded into the AC97 registers by the driver. # This allows setting the configuration prior to any applets running. #################################################### # the following settings setup 2 channel plus Mic and # Line-In on the system, plus 6 channel on the dock. # Be careful with R6E. Only 1 codec can be inputting # at a time. Setting the off codec to slots 6-9 will # effectively disable it. #################################################### 0_76588384_R3E = hex: 01, 00 ; R3E = 0x0001 0_76588384_R4C = hex: 00, 00 ; R4C = 0x0000 0_76588384_R4E = hex: F0, FF ; R4E = 0xFFF0 0_76588384_R54 = hex: 0B, 00 ; R54 = 0x000B 0_76588384_R64 = hex: 58, C2 ; R64 = 0xC258 0_76588384_R66 = hex: 04, 06 ; R66 = 0x0604 0_76588384_R68 = hex: 01, 00 ; R68 = 0x0001 0_76588384_R6E = hex: 60, 50 ; R6E = 0x5060 (VREF output off to powerup internal amp) 0_76588384_R74 = hex: 00, 88 ; R74 = 0x8800 (EAPD On for Stereo output)Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.