K810VU.INI Driver File Contents (AUDIO_XP_2K_040426.zip)

# K810VU.ini

[Models]
PCI\VEN_1106&DEV_3059&SUBSYS_01031071=this

[DelRegKeys]
HKCU\Software\Sigmatel\Settings=Yes
HKCU\Software\Sigmatel\JackSense=Yes
HKR\Settings=Yes
HKR\JackSense=Yes
HKCU\Software\Microsoft\Windows\CurrentVersion\Applets\Volume Control\SigmaTel Audio=Yes
HKU\Software\Microsoft\Windows\CurrentVersion\Applets\Volume Control\SigmaTel Audio=Yes

[Apps]
TinyUJ2=YesInvisible

#
# The following keys are used by StacApp and should be leave unchanged.
# 
[HKR\JackSense]
Mode=DWORD:0x0                   ; Reserved.  Leave 0
TabMode=DWORD:0x7A               ; Specifies which tabs StacApp will display
DefaultSpeakerConfig=DWORD:0x2   ; Default MS Spkr Config set by StacApp

#
# Specify whether to route Line-Out/Front directly from Dac A or from the Analog Mixer
#
DigitalModel=DWORD: 0            ; 1 = Dac A, 0 = mixer

#
# The following keys specify the number of different setups displayed
# by the Jack Sharing applet, and the mode that they support.  This will
# subsequently effect the menu item displayed by the Jack Sharing applet.
# Typically 4 modes used are 2 (Headphones), 4 (Stereo Speakers), 5 (Quad), and 7 (5.1) 
#
#    0 = None
#    1 = Mono Speaker
#    2 = Headphones
#    3 = Stereo Speakers (narrow)
#    4 = Stereo Speakers (wide)
#    5 = Quadraphonic (4 channel)
#    6 = Surround (4 channel)
#    7 = 5.1 Surround (6 channel)
#    All other values are invalid
#
NumSpkrSetups=DWORD:0x4          ; The number of setups defined.
SpkrSetup1=DWORD:0x2             ; Setup 1 is mode 2 (Headphones)
SpkrSetup2=DWORD:0x4             ; Setup 2 is mode 4 (Speakers)
SpkrSetup3=DWORD:0x5             ; Setup 3 is mode 5 (Quad)
SpkrSetup4=DWORD:0x7             ; Setup 4 is mode 7 (5.1)

#
# The following sections define which pins are connected to jacks
# Each pin will have properties associated with it such as the color of the jack,
# where it is located, and which mode (front, rear, center/lfe) to select when a
# speaker is plugged in and autoconfigure is set.
#
# SupportedDevices specifies which devices to allow:
#     1 = empty jack             ; if specified causes autoconfigure to disable when empty
#     2 = Microphone
#     4 = Powered speakers
#     8 = Headphones
#  0x10 = Line-In
#  0x20 = Rear/Surround speakers
#  0x40 = Center/LFE speakers
#  0x80 = SPDIF-In (not currently supported)
# 0x100 = SPDIF-Out (Not currently supported)
#
# DefaultSpeakerMode specifies which channels to configure if JackSense is
#  active and AutoConfigure is set and speakers are plugged into the jack.

# Configuration Table (informational only)
#----------------------------------------------------------------------
#        |  F/R       Front  |  Rear      Rear       Rear
#        |  Pink      Green  |  Blue      Green      Pink
#----------------------------------------------------------------------
#        |  21/22     35/36  |  39/41     35/36      21/22
#        |  UJ+M      UJ+H   |   UJ       UJ+H       UJ+M
#----------------------------------------------------------------------
# Setup1 |   Mic      HP     | Line-In     HP         Mic
# Setup2 |   Mic    Line-Out | Line-In   Line-Out     Mic
# Setup3 |   Mic     Front   |  Rear      Front       Mic
# Setup4 |  C/LFE    Front   |  Rear      Front      C/LFE
#----------------------------------------------------------------------

#
# Pins 21/22 are connected to the Mic jack on both the front and rear panels.
# It supports Speakers or Headphones.
#
[HKR\JackSense\Codec1\Pins21/22]  ; Actually, only pin 22 is used.
JackColor=DWORD:0x2               ; Jack color is pink (2=red/pink, 5=green, 6=blue)
JackLocation=DWORD:0x0            ; Front panel (0=rear, 1=front) 
JackPanelOrder=DWORD:0x3          ; 1st jack on the front panel
MicBias=DWORD: 0x64               ; Is Mic bias is provided by VRef (100 decimal)
MicBiasPolarity=DWORD:0x1         ; Is Mic bias is on when VRef is set???
SupportedDevices=DWORD:0x76       ; Mic or spkrs supported (see note above)
DefaultSpeakerMode=DWORD:0x6      ; Autoconfigure speaker as C/LFE (see note above)
PinDisabled=DWORD:0x0             ; Pin not disabled
Setup1=DWORD:0x1                  ; In setup 1 this jack is Mic
Setup2=DWORD:0x1                  ; In setup 2 this jack is Mic also
Setup3=DWORD:0x1                  ; In setup 3 this jack is Mic
Setup4=DWORD:0x6                  ; In setup 4 this jack is Center/LFE Out

#
# Pins 35/36 are connected to the HP jack on the rear panel (and front green).
# It supports Speakers or Headphones.
#
[HKR\JackSense\Codec1\Pins35/36]
JackColor=DWORD:0x5               ; Jack color is green (2=red/pink, 5=green, 6=blue)
JackLocation=DWORD:0x0            ; Rear panel (0=rear, 1=front) 
JackPanelOrder=DWORD:0x2          ; 1st jack on the front panel
SupportedDevices=DWORD:0xc        ; Headphone and Spkrs supported (see note above)
DefaultSpeakerMode=DWORD:0x2      ; Autoconfigure speaker as Front (see note above)
PinDisabled=DWORD:0x0             ; Pin not disabled
Setup1=DWORD:0x3                  ; In setup 1 (hp) this jack is Headphones
Setup2=DWORD:0x2                  ; In setup 2 (stereo) this jack is Line-Out Spkrs
Setup3=DWORD:0x2                  ; In setup 3 (quad) this jack is Front spkrs
Setup4=DWORD:0x2                  ; In setup 4 (5.1) this jack is Front spkrs

#
# Pins 39/41 are connected to the rear panel Line In (blue) jack
#
[HKR\JackSense\Codec1\Pins39/41]
JackColor=DWORD:0x6               ; Jack color is blue (2=red/pink, 5=green, 6=blue)
JackLocation=DWORD:0x0            ; Rear panel (0=rear, 1=front) 
JackPanelOrder=DWORD:0x1          ; 2nd jack on the front panel
SupportedDevices=DWORD:0x74       ; Any speaker mode supported (see note above)
DefaultSpeakerMode=DWORD:0x5      ; Autoconfigure speaker as Rear (see note above)
PinDisabled=DWORD:0x0             ; Pin not disabled
Setup1=DWORD:0x4                  ; In setup 1 (hp) this jack is Line-In
Setup2=DWORD:0x4                  ; In setup 2 (stereo) this jack is Line-In
Setup3=DWORD:0x5                  ; In setup 3 (quad) this jack is Rear spkrs
Setup4=DWORD:0x5                  ; In setup 4 (5.1) this jack is Rear spkrs

#
# Pins 43/44 are connected to the front and rear panel pink (along with 21/22)
# I've commented this out since 21/22 can do everything.
#
[HKR\JackSense\Codec1\Pins43/44]
#GpioSwitch=DWORD:0x4
#GpioPolarity=DWORD:0x1
#JackColor=DWORD:0x2               ; Jack color is pink (2=red/pink, 5=green, 6=blue)
#JackLocation=DWORD:0x0            ; Rear panel (0=rear, 1=front) 
#JackPanelOrder=DWORD:0x3          ; 2nd jack on the front panel
#SupportedDevices=DWORD:0x74       ; Any speaker mode supported (see note above)
#DefaultSpeakerMode=DWORD:0x6      ; Autoconfigure speaker as Center/LFE (see note above)
#PinDisabled=DWORD:0x0             ; Pin not disabled
#Setup1=DWORD:0x6                  ; In setup 1 (hp) this jack is Center/LFE (off)
#Setup2=DWORD:0x6                  ; In setup 2 (stereo) this jack is Center/LFE (off)
#Setup3=DWORD:0x6                  ; In setup 3 (quad) this jack is Center/LFE (off)
#Setup4=DWORD:0x6                  ; In setup 4 (5.1) this jack is Center/LFE (off)

#
# These entries control driver settings
#
[HKR\Settings]
DisableHeadphone		  =hex: 1
DisableLnlvl			  =hex: 1
DisableWaveIn2			  =hex: 1
DisablePCBeep 			  =hex: 0
DisablePhone                  	  =hex: 1
DisableAux                   	  =hex: 0
DisableMonoOut               	  =hex: 1
DisableVideo                	  =hex: 1
Disable3DControl              	  =hex: 1
DisableMonoVirtual		  =hex: 1
DisableMICSelect		  =hex: 1

MICBoost 	                  =hex: 1

WaveInMux			  =hex: 00, 00, 00, 00 ;Mic

MasterControlsMono                =hex: 1
MasterControlsAux                 =hex: 1
RecMuxMuteAtFloor		  =hex: 0
MICSelect                         =hex: 0
MICAtRecMuxVolume                 =hex: 63, D0, 13, 00       ; (0-168000)
;MICAtRecMuxVolume                =hex: 00, 30, 10, 00
MICVolume			  =hex: 90, 56, 08, 00       ; (ffdd8000-c0000),   (5 bit control).
CDVolume                          =hex: 89, F5, FF, FF       ; (ffdd8000-c0000),   (5 bit controls).
;CDVolume			   =hex: 00,f0,e9,ff
CPL_SpdifTransmitterEnabledByUser =hex: 1

EnableExtAmpControl               =hex: 0
;ExtAmpPops                        =hex: 1
;ExtAmpPowerUpOnSystemSuspend      =hex: 1
;ExtAmpPowerDownTimeInMCS          =dword: 5000 
;ExtAmpPowerUpTimeInMCS            =dword: 5000
;CodecPowerUpDelayInMCS            =dword: 1000

EnableVrefPowerDown		  =hex: 0
;VrefPowerDownTimeInMS		  =dword: 500 ;1/2 second

EnableNonPCMOnWin2K		  =hex: 1
EnableSPDIFIn			  =hex: 0
SPDIFInMute                 	  =hex: 1
SPDIFInSupportVariant       	  =hex: 2
EnableStereoMic			  =hex: 1
MultichannelEnabledByUser		  =hex: 1
EnableNewVolumeControls	    	  =hex: 1

#
# These settings control the values loaded into the AC97 registers by the driver.
# This allows setting the configuration prior to any applets running.
#
0_76588384_R64   =hex: 80, 03      ; R64  Pins 35/36 = Mixer
0_76588384_R66   =hex: 01, 02      ; R66  Line-In = 23/24, Mic = 21/22
#0_76588384_R68   =hex: 40, 08      ; R68  SPDIF-In -> ACLink, Low level
0_76588384_R68   =hex: 00, 00      ; R68  SPDIF-In Disabled
0_76588384_R6E   =hex: 40, 90      ; R6E
0_76588384_R74   =hex: 00, 00      ; R74
0_76588384_R3E   =hex: 00, 00      ; R3E - Enable GPIOs
0_76588384_R4C   =hex: 0f, 00      ; R4C - GPIOs - all inputs
0_76588384_R4E   =hex: 0f, 00      ; R4E
0_76588384_R54   =hex: 00, 00      ; R54 - GPIO states - all off

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web1, load: 0.70