;**********************************************************************
; H320VCP.INI
;***********************************************************************
[VCP]
vcx_dwVidScnInterlaceMode = 0
vcx_dwVidDramControl = 0x00 ; 0x0-Driver, 0x355-1M, 0x255-2M; 0x395-4m
bEncExtraGrabFrame = 1 ; 0 for 1Meg, 1 for 2Meg
; Needed for 8x8 VCP release 3.0 code.
vcx_bH261SkipVpReadback = 1
dbg_dwDecBuffSize = 0x1710
; audio params
vcx_h261_audio = 0 ; H320 ; was 1 ; 1/0 enable/audio
;; added for T.123 support
vcx_wH242RxMlpSid=0x2901
;; stream for the T.123 stack and farsite
;;stream 0x29FF = c:\farsite3\farsite3.exe
;***********************************************************************
[H.320] ; This section is specific to H320.
vcx_bAudMute=1
vcx_bAudPrivacy=1
vcx_bAudNeedsDownload=0
vcx_bH242MuLawDefault=1
; Trigger Counts
vcx_dwH242TxLsdTriggerCount = 30
vcx_dwH242TxLsdDataCount = 50
vcx_dwH242RxLsdTriggerCount = 30
vcx_dwH242RxLsdDataCount = 50
vcx_dwH242TxHsdTriggerCount = 20
vcx_dwH242TxHsdDataCount = 40
vcx_dwH242RxHsdTriggerCount = 20
vcx_dwH242RxHsdDataCount = 40
vcx_dwH242TxMlpTriggerCount = 0
vcx_dwH242TxMlpDataCount = 100
vcx_dwH242RxMlpTriggerCount = 20
vcx_dwH242RxMlpDataCount = 100
; H.221 Stuff - TDM settings for Promptus ISDN card
0x2000E004 = 0x0E ; TDM: xmt delay & phase
0x2000E008 = 0x0E ; TDM: rcv delay & phase
0x2000E00C = 0x81 ; TDM: initialization of tdmctl
;;theses streams needed for Answering machine
stream 0x0e20 = vid1.in
stream 0x0e40 = aud1.in
stream 0x0800 = \\.\mailslot\h320_005.vtp
vcx_afH242LocalCaps[0]:4 = 0x00000000 ; ignored
vcx_afH242LocalCaps[1]:4 = 0x00000000 ; ignored
vcx_afH242LocalCaps[2]:4 = 0x00000000 ; ignored
vcx_afH242LocalCaps[3]:4 = 0x00000000 ; ignored
vcx_afH242LocalCaps[4]:4 = 0x013F0F3E ; (1-6)B, (128-384), all audio
vcx_afH242LocalCaps[5]:4 = 0x00307FFE ; CIF, QCIF, Enable data channel
vcx_afH242LocalCaps[16]:4 = 0x00000201 ; MLP 14.4K & 24K
vcx_bH242RestrictAdjacent = 0
vcx_bH242NewCapSet = 1 ; use above capabilities
vcx_bVidPciVideo=0
vcx_bH261EncAnnexdGrabEnc=1
vcx_dwH261AnnexDGoodQ=3
vcx_dwH261AnnexDGoodQThr=100
;***********************************************************************
; [H.261] ; This section is common to H320 and H261
; Variables common to all H261 configurations
stream 0x4102 = C:\WINNT\System32\Osprey\vph261.010
vcx_dwH261EncBitrate = 96000 ; in bits per second
vcx_dwH261EncTnr = 0 ; turn on for rev3 chip only
vcx_bBchOn = 0 ; 0 for no BCH
vcx_dwH261EncIntraQuant = 10 ; Quant for the intra frame
vcx_dwH261EncMotion15 = 1 ; switch for +-15/+-7 motion
vcx_dwH261EncRateBuffer = 1 ; if 0 will use MaxQuant always
; CIF specific settings
vcx_dwH261EncCif = 1
vcx_dwH261EncMaxQuantCif = 10 ; 0 - 31 large=fast, bad quality
vcx_dwH261EncFrameRateIndexCif = 1 ; max fps = (30 fps / index)
;vcx_dwH261EncIRefPeriodCif = 17 ; Not in H320 executable
vcx_dwH261EncRepThrCif = 20 ; replenishment threshold : 0 - 63
; QCIF specific settings
vcx_dwH261EncMaxQuantQcif = 10 ; 0 - 31 large=fast, bad quality
vcx_dwH261EncFrameRateIndexQcif = 1 ; max fps = (30 fps / index)
;vcx_dwH261EncIRefPeriodQcif = 17 ; Not in H320 executable
;***********************************************************************
[VIDIN.NTSC] ; Settings for NTSC video input source
vcx_dwH261EncNTSC = 1
vcx_dwH261DecNTSC = 1
; NTSC CAMERA SETTINGS
vcx_dwVidCamHstart = 140
vcx_dwVidCamHendCif = 840
vcx_dwVidCamHendQcif = 836
vcx_dwVidCamVstart = 17
vcx_dwVidCamVend = 256
vcx_dwVidCamVertirq = 256
vcx_dwVidCamMode0Cif = 0x01ED ; 7 tap filter with uv skew
vcx_dwVidCamMode0Qcif = 0x01ED ; 7 tap filter with uv skew
;***********************************************************************
[VIDIN.PAL] ; Settings for PAL video input source
vcx_dwH261EncNTSC = 0
vcx_dwH261DecNTSC = 0
; PAL CAMERA SETTINGS
vcx_dwVidCamHstart = 150 ; Anything less has color problems at left edge
vcx_dwVidCamHendCif = 850 ;
vcx_dwVidCamHendQcif = 846 ;
vcx_dwVidCamVstart = 21 ; 4/23/98 less than 16 gets junk at top of image
; greater than 16 gets junk at bottom of image
; 16 leaves blank lines at the top of the image
vcx_dwVidCamVend = 308
vcx_dwVidCamVertirq = 308 ; greater doesn't update with our PAL camera
vcx_dwVidCamMode0Cif = 0x11ED ; 4/23/98 3 tap filter with uv skew
vcx_dwVidCamMode0Qcif = 0x11ED ; 4/23/98 3 tap filter with uv skew
dbg_dwAnnexdFieldSize = 288 ;
;***********************************************************************
[VIDOUT.PCI]
; Settings for digital video out via PCI to video adapter or buffer on host
vcx_dwVidScnMisc0 = 0x18
vcx_dwVidScnOutputcntl = 0x2010; KH, was 2380
vcx_dwVidScnCounterCtl = 0x11; KH, was 0x16
vcx_dwVidScnInterlaceMode = 0x0
vcx_dwVidScnHstart = 12 ; 4/23/98 LEM 10;
vcx_dwVidScnHend = 365 ; 4/23/98 LEM 363; (352+vcx_dwVidScnHstart+1)
vcx_dwVidScnHblankStart = 365 ; 4/23/98 LEM 363;
vcx_dwVidScnHblankStop = 10
vcx_dwVidScnHsyncPeriod = 820
vcx_dwVidScnHsyncWidth = 2
vcx_dwVidScnVstart = 3;
vcx_dwVidScnVblankStop = 2;
vcx_dwVidScnVsyncDelayedOdd = 1;
vcx_dwVidScnVsyncDelayedEven = 410;
vcx_dwVidScnVsyncPeriodOdd = 490;
vcx_dwVidScnVsyncPeriodEven = 490;
vcx_dwVidScnVertirq = 480;
vcx_dwVidScnVsyncWidth = 3
; CIF specific settings
vcx_dwVidScnYStartstopCif = 0x2c48; (88 << 7) | 72 ; 0x2c48
vcx_dwVidScnUVStartstopCif = 0x1624; (44 << 7) | 36
vcx_dwVidScnIncvalCif = 0x1000
; QCIF specific settings
vcx_dwVidScnYStartstopQcif = 0x1624 ; H320 ; was 0x1817
vcx_dwVidScnUVStartstopQcif = 0x0B12 ; H320 ; was 0x0d0c
vcx_dwVidScnIncvalQcif = 0x0800 ; H320 ; was 0x1000
vcx_dwVidDmaScaleValueQcif = 0x10 ; H320 ; was 0x20
vcx_dwVidDmaScaleTypeQcifLocal = 0x55 ; H320 ; was commented out
vcx_dwVidDmaScaleTypeQcifFar = 0x55 ; H320 ; was commneted out
vcx_osprey_local_and_far = 1;
vcx_osprey_local_and_far_select = 2; Default is far view
vcx_release_wait = 0
;***********************************************************************
[VIDOUT.PCI.NTSC] ; Settings for NTSC video out via PCI to host
; NTSC SCREEN SETTINGS
; CIF 244, 253 CIFs 292, 301
; QCIF 124, 133 QCIFs 148, 157
vcx_dwVidScnVend = 244 ;
vcx_dwVidScnVblankStart = 253 ;
vcx_dwVidScnVertsize = 239 ;
vcx_dwVidScnVendCif = 244 ;
vcx_dwVidScnVblankStartCif = 253 ;
vcx_dwVidScnVendQcif = 244 ; H320 ; was 124
vcx_dwVidScnVblankStartQcif = 253 ; H320 ; was 133
;***********************************************************************
[VIDOUT.PCI.PAL] ; Settings for PAL video out via PCI to host
; PAL SCREEN SETTINGS
; CIF 244, 253 CIFs 292, 301
; QCIF 124, 133 QCIFs 148, 157
vcx_dwVidScnVend = 292 ;
vcx_dwVidScnVblankStart = 301 ;
vcx_dwVidScnVertsize = 287 ;
vcx_dwVidScnVendCif = 291 ; 4/27/98 LEM 292
vcx_dwVidScnVblankStartCif = 301 ;
vcx_dwVidScnVendQcif = 291 ; 4/27/98 LEM 292 was 148
vcx_dwVidScnVblankStartQcif = 301 ; H320 ; was 157
;***********************************************************************
[VIDOUT.BT] ; Settings for analog video out via Brooktree D/A
vcx_dwVidScnMisc0 = 0x18; [0x18]
vcx_dwVidScnOutputcntl = 0x2380; [0x2010]
vcx_dwVidScnCounterCtl = 0x17; [0x11]; VCP is master
vcx_dwVidScnInterlaceMode = 0x0; [0x0]
vcx_dwVidScnYStartstopCif = 0x2c48; (88 << 7) | 72; [0x2c48]
vcx_dwVidScnUVStartstopCif = 0x1624; (44 << 7) | 36; [0x1624]
vcx_dwVidScnIncvalCif = 0x800; [0x1000]
vcx_dwVidScnYStartstopQcif = 0x119b; (35 << 7) | 27 [0x119b]
vcx_dwVidScnUVStartstopQcif = 0x0a13; (20<< 7) | 19 [0x0a13]
vcx_dwVidScnIncvalQcif = 0x400; [0x400]
vcx_dwVidDmaScaleValueQcif = 0x10; [0x20]
vcx_dwVidDmaScaleTypeQcifLocal = 0x55 ; H320 added
vcx_dwVidDmaScaleTypeQcifFar = 0x55 ; H320 added
vcx_osprey_local_and_far = 1;
vcx_osprey_local_and_far_select = 2; Default is far view
vcx_release_wait = 0
;***********************************************************************
[VIDOUT.BT.NTSC] ; Settings for analog NTSC out with VCP as sync. master
vcx_dwVidScnHstart = 131 ; 4/23/98 LEM 141 ; MUST BE ODD!
vcx_dwVidScnHend = 834 ; 4/23/98 LEM 844 ; (Hstart+704-1)
vcx_dwVidScnHblankStart = 833 ; 4/23/98 LEM 840
vcx_dwVidScnHblankStop = 135 ; 4/23/98 LEM 141
vcx_dwVidScnHsyncPeriod = 858
vcx_dwVidScnHsyncWidth = 60
vcx_dwVidScnVstart = 18; [10]
vcx_dwVidScnVend = 259 ; H320 ; was 251; [251]
vcx_dwVidScnVblankStart = 259 ; H320 ; was 260; [260]
vcx_dwVidScnVblankStop = 19; [3]
vcx_dwVidScnVsyncDelayedOdd = 429; [858]
vcx_dwVidScnVsyncDelayedEven = 857; [20]
vcx_dwVidScnVsyncWidth = 3; [3]
vcx_dwVidScnVsyncPeriodOdd = 263; [262]
vcx_dwVidScnVsyncPeriodEven = 262; [262]
vcx_dwVidScnVertirq = 260; [252]
vcx_dwVidScnVendCif = 259 ; H320 ; was 251; [251]
vcx_dwVidScnVblankStartCif = 259 ; H320 ; was 260; [260]
vcx_dwVidScnVendQcif = 259 ; H320 ; was 251; [131]
vcx_dwVidScnVblankStartQcif = 259 ; H320 ; was 260; [140]
;***********************************************************************
[VIDOUT.BT.PAL] ; Settings for analog PAL out with VCP as sync. master
vcx_dwVidScnHstart = 143 ; 4/23/98 LEM 141 ; MUST BE ODD!
vcx_dwVidScnHend = 846 ; 4/23/98 LEM 844 ; (Hstart+704-1)
vcx_dwVidScnHblankStart = 843 ; 4/23/98 LEM 840
vcx_dwVidScnHblankStop = 146 ; 4/23/98 LEM 141
vcx_dwVidScnHsyncPeriod = 864 ; 4/23/98 LEM 858
vcx_dwVidScnHsyncWidth = 60
vcx_dwVidScnVstart = 21; [10]
vcx_dwVidScnVend = 308; [251]
vcx_dwVidScnVblankStart = 307; [260]
vcx_dwVidScnVblankStop = 24; [3]
vcx_dwVidScnVsyncDelayedOdd = 431 ; 4/23/98 LEM 429
vcx_dwVidScnVsyncDelayedEven = 20 ; 4/23/98 LEM 857
vcx_dwVidScnVsyncPeriodOdd = 312 ; 4/23/98 LEM 311
vcx_dwVidScnVsyncPeriodEven = 313 ; 4/23/98 LEM 310
vcx_dwVidScnVertirq = 309; [252]
vcx_dwVidScnVendCif = 308; [251]
vcx_dwVidScnVblankStartCif = 307; [260]
vcx_dwVidScnVendQcif = 308; [131]
vcx_dwVidScnVblankStartQcif = 307; [140]
;***********************************************************************
; eof
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.