;********************************************************************** ; H320VCP1.INI ;*********************************************************************** [VCP] vcx_dwVidScnInterlaceMode = 0 vcx_dwVidDramControl = 0x00 ; 0x0-Driver, 0x355-1M, 0x255-2M; 0x395-4m bEncExtraGrabFrame = 1 ; 0 for 1Meg, 1 for 2Meg ; Needed for 8x8 VCP release 3.0 code. vcx_bH261SkipVpReadback = 1 dbg_dwDecBuffSize = 0x1710 ; audio params vcx_h261_audio = 0 ; H320 ; was 1 ; 1/0 enable/audio ;; added for T.123 support vcx_wH242RxMlpSid=0x2901 ;; stream for the T.123 stack and farsite ;;stream 0x29FF = c:\farsite3\farsite3.exe ;*********************************************************************** [H.320] ; This section is specific to H320. vcx_bAudMute=1 vcx_bAudPrivacy=1 vcx_bAudNeedsDownload=0 vcx_bH242MuLawDefault=1 ; Trigger Counts vcx_dwH242TxLsdTriggerCount = 30 vcx_dwH242TxLsdDataCount = 50 vcx_dwH242RxLsdTriggerCount = 30 vcx_dwH242RxLsdDataCount = 50 vcx_dwH242TxHsdTriggerCount = 20 vcx_dwH242TxHsdDataCount = 40 vcx_dwH242RxHsdTriggerCount = 20 vcx_dwH242RxHsdDataCount = 40 vcx_dwH242TxMlpTriggerCount = 0 vcx_dwH242TxMlpDataCount = 100 vcx_dwH242RxMlpTriggerCount = 20 vcx_dwH242RxMlpDataCount = 100 ; H.221 Stuff - TDM settings for Promptus ISDN card 0x2000E004 = 0x0E ; TDM: xmt delay & phase 0x2000E008 = 0x0E ; TDM: rcv delay & phase 0x2000E00C = 0x81 ; TDM: initialization of tdmctl ;;theses streams needed for Answering machine stream 0x0e20 = vid1.in stream 0x0e40 = aud1.in stream 0x0800 = \\.\mailslot\h320_001.vtp vcx_afH242LocalCaps[0]:4 = 0x00000000 ; ignored vcx_afH242LocalCaps[1]:4 = 0x00000000 ; ignored vcx_afH242LocalCaps[2]:4 = 0x00000000 ; ignored vcx_afH242LocalCaps[3]:4 = 0x00000000 ; ignored vcx_afH242LocalCaps[4]:4 = 0x013F0F3E ; (1-6)B, (128-384), all audio vcx_afH242LocalCaps[5]:4 = 0x00307FFE ; CIF, QCIF, Enable data channel vcx_afH242LocalCaps[16]:4 = 0x00000201 ; MLP 14.4K & 24K vcx_bH242RestrictAdjacent = 0 vcx_bH242NewCapSet = 1 ; use above capabilities vcx_bVidPciVideo=0 vcx_bH261EncAnnexdGrabEnc=1 vcx_dwH261AnnexDGoodQ=3 vcx_dwH261AnnexDGoodQThr=100 ;*********************************************************************** ; [H.261] ; This section is common to H320 and H261 ; Variables common to all H261 configurations stream 0x4102 = C:\WINNT\System32\Osprey\vph261.010 vcx_dwH261EncBitrate = 96000 ; in bits per second vcx_dwH261EncTnr = 0 ; turn on for rev3 chip only vcx_bBchOn = 0 ; 0 for no BCH vcx_dwH261EncIntraQuant = 10 ; Quant for the intra frame vcx_dwH261EncMotion15 = 1 ; switch for +-15/+-7 motion vcx_dwH261EncRateBuffer = 1 ; if 0 will use MaxQuant always ; CIF specific settings vcx_dwH261EncCif = 1 vcx_dwH261EncMaxQuantCif = 10 ; 0 - 31 large=fast, bad quality vcx_dwH261EncFrameRateIndexCif = 1 ; max fps = (30 fps / index) ;vcx_dwH261EncIRefPeriodCif = 17 ; Not in H320 executable vcx_dwH261EncRepThrCif = 20 ; replenishment threshold : 0 - 63 ; QCIF specific settings vcx_dwH261EncMaxQuantQcif = 10 ; 0 - 31 large=fast, bad quality vcx_dwH261EncFrameRateIndexQcif = 1 ; max fps = (30 fps / index) ;vcx_dwH261EncIRefPeriodQcif = 17 ; Not in H320 executable ;*********************************************************************** [VIDIN.NTSC] ; Settings for NTSC video input source vcx_dwH261EncNTSC = 1 vcx_dwH261DecNTSC = 1 ; NTSC CAMERA SETTINGS vcx_dwVidCamHstart = 140 vcx_dwVidCamHendCif = 840 vcx_dwVidCamHendQcif = 836 vcx_dwVidCamVstart = 17 vcx_dwVidCamVend = 256 vcx_dwVidCamVertirq = 256 vcx_dwVidCamMode0Cif = 0x01ED ; 7 tap filter with uv skew vcx_dwVidCamMode0Qcif = 0x01ED ; 7 tap filter with uv skew ;*********************************************************************** [VIDIN.PAL] ; Settings for PAL video input source vcx_dwH261EncNTSC = 0 vcx_dwH261DecNTSC = 0 ; PAL CAMERA SETTINGS vcx_dwVidCamHstart = 150 ; Anything less has color problems at left edge vcx_dwVidCamHendCif = 850 ; vcx_dwVidCamHendQcif = 846 ; vcx_dwVidCamVstart = 21 ; 4/23/98 less than 16 gets junk at top of image ; greater than 16 gets junk at bottom of image ; 16 leaves blank lines at the top of the image vcx_dwVidCamVend = 308 vcx_dwVidCamVertirq = 308 ; greater doesn't update with our PAL camera vcx_dwVidCamMode0Cif = 0x11ED ; 4/23/98 3 tap filter with uv skew vcx_dwVidCamMode0Qcif = 0x11ED ; 4/23/98 3 tap filter with uv skew dbg_dwAnnexdFieldSize = 288 ; ;*********************************************************************** [VIDOUT.PCI] ; Settings for digital video out via PCI to video adapter or buffer on host vcx_dwVidScnMisc0 = 0x18 vcx_dwVidScnOutputcntl = 0x2010; KH, was 2380 vcx_dwVidScnCounterCtl = 0x11; KH, was 0x16 vcx_dwVidScnInterlaceMode = 0x0 vcx_dwVidScnHstart = 12 ; 4/23/98 LEM 10; vcx_dwVidScnHend = 365 ; 4/23/98 LEM 363; (352+vcx_dwVidScnHstart+1) vcx_dwVidScnHblankStart = 365 ; 4/23/98 LEM 363; vcx_dwVidScnHblankStop = 10 vcx_dwVidScnHsyncPeriod = 820 vcx_dwVidScnHsyncWidth = 2 vcx_dwVidScnVstart = 3; vcx_dwVidScnVblankStop = 2; vcx_dwVidScnVsyncDelayedOdd = 1; vcx_dwVidScnVsyncDelayedEven = 410; vcx_dwVidScnVsyncPeriodOdd = 490; vcx_dwVidScnVsyncPeriodEven = 490; vcx_dwVidScnVertirq = 480; vcx_dwVidScnVsyncWidth = 3 ; CIF specific settings vcx_dwVidScnYStartstopCif = 0x2c48; (88 << 7) | 72 ; 0x2c48 vcx_dwVidScnUVStartstopCif = 0x1624; (44 << 7) | 36 vcx_dwVidScnIncvalCif = 0x1000 ; QCIF specific settings vcx_dwVidScnYStartstopQcif = 0x1624 ; H320 ; was 0x1817 vcx_dwVidScnUVStartstopQcif = 0x0B12 ; H320 ; was 0x0d0c vcx_dwVidScnIncvalQcif = 0x0800 ; H320 ; was 0x1000 vcx_dwVidDmaScaleValueQcif = 0x10 ; H320 ; was 0x20 vcx_dwVidDmaScaleTypeQcifLocal = 0x55 ; H320 ; was commented out vcx_dwVidDmaScaleTypeQcifFar = 0x55 ; H320 ; was commneted out vcx_osprey_local_and_far = 1; vcx_osprey_local_and_far_select = 2; Default is far view vcx_release_wait = 0 ;*********************************************************************** [VIDOUT.PCI.NTSC] ; Settings for NTSC video out via PCI to host ; NTSC SCREEN SETTINGS ; CIF 244, 253 CIFs 292, 301 ; QCIF 124, 133 QCIFs 148, 157 vcx_dwVidScnVend = 244 ; vcx_dwVidScnVblankStart = 253 ; vcx_dwVidScnVertsize = 239 ; vcx_dwVidScnVendCif = 244 ; vcx_dwVidScnVblankStartCif = 253 ; vcx_dwVidScnVendQcif = 244 ; H320 ; was 124 vcx_dwVidScnVblankStartQcif = 253 ; H320 ; was 133 ;*********************************************************************** [VIDOUT.PCI.PAL] ; Settings for PAL video out via PCI to host ; PAL SCREEN SETTINGS ; CIF 244, 253 CIFs 292, 301 ; QCIF 124, 133 QCIFs 148, 157 vcx_dwVidScnVend = 292 ; vcx_dwVidScnVblankStart = 301 ; vcx_dwVidScnVertsize = 287 ; vcx_dwVidScnVendCif = 291 ; 4/27/98 LEM 292 vcx_dwVidScnVblankStartCif = 301 ; vcx_dwVidScnVendQcif = 291 ; 4/27/98 LEM 292 was 148 vcx_dwVidScnVblankStartQcif = 301 ; H320 ; was 157 ;*********************************************************************** [VIDOUT.BT] ; Settings for analog video out via Brooktree D/A vcx_dwVidScnMisc0 = 0x18; [0x18] vcx_dwVidScnOutputcntl = 0x2380; [0x2010] vcx_dwVidScnCounterCtl = 0x17; [0x11]; VCP is master vcx_dwVidScnInterlaceMode = 0x0; [0x0] vcx_dwVidScnYStartstopCif = 0x2c48; (88 << 7) | 72; [0x2c48] vcx_dwVidScnUVStartstopCif = 0x1624; (44 << 7) | 36; [0x1624] vcx_dwVidScnIncvalCif = 0x800; [0x1000] vcx_dwVidScnYStartstopQcif = 0x119b; (35 << 7) | 27 [0x119b] vcx_dwVidScnUVStartstopQcif = 0x0a13; (20<< 7) | 19 [0x0a13] vcx_dwVidScnIncvalQcif = 0x400; [0x400] vcx_dwVidDmaScaleValueQcif = 0x10; [0x20] vcx_dwVidDmaScaleTypeQcifLocal = 0x55 ; H320 added vcx_dwVidDmaScaleTypeQcifFar = 0x55 ; H320 added vcx_osprey_local_and_far = 1; vcx_osprey_local_and_far_select = 2; Default is far view vcx_release_wait = 0 ;*********************************************************************** [VIDOUT.BT.NTSC] ; Settings for analog NTSC out with VCP as sync. master vcx_dwVidScnHstart = 131 ; 4/23/98 LEM 141 ; MUST BE ODD! vcx_dwVidScnHend = 834 ; 4/23/98 LEM 844 ; (Hstart+704-1) vcx_dwVidScnHblankStart = 833 ; 4/23/98 LEM 840 vcx_dwVidScnHblankStop = 135 ; 4/23/98 LEM 141 vcx_dwVidScnHsyncPeriod = 858 vcx_dwVidScnHsyncWidth = 60 vcx_dwVidScnVstart = 18; [10] vcx_dwVidScnVend = 259 ; H320 ; was 251; [251] vcx_dwVidScnVblankStart = 259 ; H320 ; was 260; [260] vcx_dwVidScnVblankStop = 19; [3] vcx_dwVidScnVsyncDelayedOdd = 429; [858] vcx_dwVidScnVsyncDelayedEven = 857; [20] vcx_dwVidScnVsyncWidth = 3; [3] vcx_dwVidScnVsyncPeriodOdd = 263; [262] vcx_dwVidScnVsyncPeriodEven = 262; [262] vcx_dwVidScnVertirq = 260; [252] vcx_dwVidScnVendCif = 259 ; H320 ; was 251; [251] vcx_dwVidScnVblankStartCif = 259 ; H320 ; was 260; [260] vcx_dwVidScnVendQcif = 259 ; H320 ; was 251; [131] vcx_dwVidScnVblankStartQcif = 259 ; H320 ; was 260; [140] ;*********************************************************************** [VIDOUT.BT.PAL] ; Settings for analog PAL out with VCP as sync. master vcx_dwVidScnHstart = 143 ; 4/23/98 LEM 141 ; MUST BE ODD! vcx_dwVidScnHend = 846 ; 4/23/98 LEM 844 ; (Hstart+704-1) vcx_dwVidScnHblankStart = 843 ; 4/23/98 LEM 840 vcx_dwVidScnHblankStop = 146 ; 4/23/98 LEM 141 vcx_dwVidScnHsyncPeriod = 864 ; 4/23/98 LEM 858 vcx_dwVidScnHsyncWidth = 60 vcx_dwVidScnVstart = 21; [10] vcx_dwVidScnVend = 308; [251] vcx_dwVidScnVblankStart = 307; [260] vcx_dwVidScnVblankStop = 24; [3] vcx_dwVidScnVsyncDelayedOdd = 431 ; 4/23/98 LEM 429 vcx_dwVidScnVsyncDelayedEven = 20 ; 4/23/98 LEM 857 vcx_dwVidScnVsyncPeriodOdd = 312 ; 4/23/98 LEM 311 vcx_dwVidScnVsyncPeriodEven = 313 ; 4/23/98 LEM 310 vcx_dwVidScnVertirq = 309; [252] vcx_dwVidScnVendCif = 308; [251] vcx_dwVidScnVblankStartCif = 307; [260] vcx_dwVidScnVendQcif = 308; [131] vcx_dwVidScnVblankStartQcif = 307; [140] ;*********************************************************************** ; eofDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.