====================================================================== ALi M5228 ATA/RAID Controller and M5281 SATA/RAID controller driver Kit. Copyright 2003 ALi Corporation. All Rights Reserved ====================================================================== ------------ INTRODUCTION ------------ This driver supports ALi M5228 ATA/RAID Controller and M5281 SATA/RAID controller. ------------------------- CONTENTS OF THIS DOCUMENT ------------------------- 1. Installation Instructions 2. Uninstallation Instructions 3. Driver File List 4. Driver Change List ---------------------------- 1. Installation Instructions ---------------------------- After the adapter is installed and recognized by computer, user can start the installation of driver. ---------------------------------------------------------------------- * Windows 98/ME Installation After Windows 98/ME is start-up, Windows system will automatically find the newly installed adapter and prompt user to install its driver. Follow these steps to install the driver: A) With installation setup program: 1. When the Found New Hardware Wizard windows appear, click Next button all the following windows. Then the driver will not be installed. 2. Double click setup.exe; 3. Confirm the following dialogue windows, and restart the computer when system prompt user to restart. B) Manual installation: 1. After the Add New Hardware Wizard window appears(PCI Mass Storage Controller), press Next button until the window with Specify a location item appears; 2. Insert the driver diskette, then select the Specify a loaction item and type in the driver loaction: A:\Win98_ME, then click on Next button to continue; 3. Confirm the following dialogue windows, and restart the computer when system prompt user to restart; 4. After rebooting, Windows will automatically find ALi M5281 SATA/RAID Controller and install its drivers. 5. Repeat step 1 to install ALi M5228 ATA/RAID Controller. ---------------------------------------------------------------------- * Windows NT4.0 Install driver under existing Windows NT4.0 A) With installation setup program: 1. Double click setup.exe; 2. Confirm the following dialogue windows, and restart the computer when system prompt user to restart. B) Manual installation: 1. Click Start-->Settings-->Control Panel, then double-click on the SCSI Adapters icon; 2. Within the follow-up window, select Driver item, then click on Add button; 3. Within the follow-up window, click on Have Disk...button, the "Install From Disk" window will appear. 4. Insert the driver diskette, and type in the path of driver location: A:\Win_NT in the above window, then click OK; 5. Within the follow-up window, select ALi M5281 SATA/RAID Controller item, then click OK; 6. Confirm the follow-up system prompts to finsh the driver installation; 7. Repeat step 1, but select ALi M5228 ATA/RAID Controller at step 5; If both controllers are installed, go to next step; 8. When installation finshed, restart the computer. Install driver during WindowsNT4.0 installation 1. Press F6 key when the installation program prompt "Setup is inspecting your computer's hardware configuration"; 2. The installation will continue. Later, installation program will prompt user to press S key to specify other devices, then press S key; 3. Within the follow-up device type window, select Other, then press ENTER to confirm; 4. Installation program will prompt user to insert the driver diskette and then press ENTER to confirm; 5. Within the follow-up window, select ALi M5281 SATA/RAID Controller, then press ENTER to confirm; 6. The follow-up window will list out the devices to be installed, in which selected ALi controller(s) will be included; 7. Repeat step 2, but select ALi M5228 ATA/RAID Controller at step 5; If both controllers are installed, go to next step; 8. If user want to install other devices, please operate at this time. If all devices have been installed, go to next step 9. Press ENTER to confirm the devices to be installed and continue the installation of Windows NT4.0. ---------------------------------------------------------------------- * Windows 2000 Install driver under existing Windows 2000 After Windows 2000 is start-up, Windows system will automatically find the newly installed adapter and prompt user to install its driver. Please follow these steps to install the driver: A) With installation setup program: 1. When the Found New Hardware Wizard windows appear, click Cancel button to end the Wizard. 2. Double click setup.exe; 3. Confirm the following dialogue windows, and restart the computer when system prompt user to restart. B) Manual installation: 1. When the Found New Hardware Wizard windows appear(Mass Storage Controller), click Next button to continue, in the follow-up window, please select Display a list... and then click Next to continue; 2. In the follow-up window, select SCSI and RAID Controllers and then click Next to continue; 3. In the follow-up window, click Have Disk..., then insert the driver diskette and type in the driver location: A:\\Win_2000, then click OK to continue; 4. In the follow-up window, select ALi M5281 SATA/RAID Controller, then click Next to continue; 5. Confirm the followup windows and click the Finish button to continue; 6. Please confirm the Digital Signature Not Found window when it appear, when finshed, please restart the computer; 7. Reapeat step 1, but select ALi M5228 ATA/RAID Controller at step 4. Install driver during Windows 2000 installation (Recommend users copy the driver to a floppy diskette's root directory) 1. Booting from CD-ROM, when the Windows 2000 Setup blue screen appear and prompt user to Press F6 if you need to install third party SCSI or RAID driver, please press F6 key: 2. The setup program will continue, later when the setup program prompt user if to specify additional adapetrs, please press S Key. 3. Then the setup program will promot user to insert the driver diskette. Please insert the driver diskette, then press ENTER to continue; 4. The follow-up window will list out the installation choices, please select ALi M5281 SATA/RAID Controller for Windows 2000 and press ENTER to continue; 5. The Follow-up window will list out the devices to be installed, in which selected ALi controller should be included; 6. Repeat step 2, but select ALi M5228 ATA/RAID Controller at step 5; If both controllers are installed, go to next step; 7 If user want to install oher devices, please operate at this time. If all devices have been successfully installed, go to next step. 8. Press ENTER to continue Windows 2000 setup. ---------------------------------------------------------------------- * Windows XP Install driver under existing Windows XP After Windows XP is start-up, Windows system will automatically find the newly installed adapter and prompt user to install its driver. Please follow these steps to install the driver: A) With installation setup program: 1. When the Found New Hardware Wizard windows appear, click Cancel button to end the Wizard. 2. Double click setup.exe; 3. Confirm the following dialogue windows, and restart the computer when system prompt user to restart. B) Manual installation: 1. When the Found New Hardware Wizard windows appear(Mass Storage Controller), select Install from a list or specify location(Advanced) and click Next to continue; 2. In the follow-up window, please select Don't search, I will choose the driver to install, then click Next to continue; 3. In the follow-up window, please select SCSI and RAID controllers, and then click Next to continue; 3. In the follow-up window, click Have Disk..., then insert the driver diskette and type in the driver location: A:\\Win_XP, then click OK to continue; 4. In the follow-up window, select ALi M5281 SATA/RAID Controller, then click Next to continue; 5. Confirm the followup windows and click the Finish button to continue; 6. Please confirm the Digital Signature Not Found window when it appear, when finshed, please restart the computer; 7. Reapeat step 1, but select ALi M5228 ATA/RAID Controller at step 4. Install driver during Windows XP installation (Recommend users copy the driver to a floppy diskette's root directory) 1. Booting from CD-ROM, when the Windows XP Setup blue screen appear and prompt user to Press F6 if you need to install third party SCSI or RAID driver, please press F6 key: 2. The setup program will continue, later when the setup program prompt user if to specify additional adapetrs, please press S Key. 3. Then the setup program will promot user to insert the driver diskette. Please insert the driver diskette, then press ENTER to continue; 4. The follow-up window will list out the installation choices, please select ALi ALi M5281 SATA/RAID Controller for Windows XP and press ENTER to continue; 5. The Follow-up window will list out the devices to be installed, in which selected ALi controller(s) should be included; 6. Repeat step 2, but select ALi M5228 ATA/RAID Controller at step 5; If both controllers are installed, go to next step; 7 If user want to install oher devices, please operate at this time. If all devices have been successfully installed, please go to next step. 8. Press ENTER to continue Windows XP setup. ------------------------------ 2. Uninstallation Instructions ------------------------------ * Uninstall from Add/Remove Programs (This method is recommended if driver is previously installed by Setup program.) 1. Start Add/Remove Programs from Control Panel. 2. Select "ALi RAID Driver" item. 3. Click on "Remove" button. * Uninstall from Device Manager 1. Start Device Manager from Control Panel's System applet. 2. Right click on "ALi M5228 ATA/RAID Controller" or "ALi M5281 SATA/RAID Controller" item, then select "Remove" (or "Uninstall") item from the popup menu. ------------------- 3. Driver File List ------------------- SATA50XX Driver Folder |- win98_me Windows 98/ME driver | |_ m5228.inf | |_ m5228.mpd | |_ m5281.inf | \_ m5281.mpd |- win_nt Windows NT 4.0 driver | |_ m5228.inf | |_ m5228.sys | |_ m5281.inf | \_ m5281.sys |- win_2000 Windows 2000 driver | |_ m5228.inf | |_ m5228.sys | |_ m5281.inf | \_ m5281.sys |- win_xp Windows XP driver | |_ m5228.inf | |_ m5228.sys | |_ m5281.inf | \_ m5281.sys |- disk1 Driver disk label \_ txtsetup.oem Windows NT/2k/XP setup file --------------------- 5. Driver Change List --------------------- 5.0.2.3 07/0X/2003 1. Fix 5283 PATA first channel detection problem. 2. Fix JBOD partition format error. 3. Fix NT4 can't create RAID error.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.