1. ProaudioBasic16.zip Driver
2. MVINST.INF File Contents

MVINST.INF Driver File Contents (ProaudioBasic16.zip)

0 Fusion CD 16 Quick Start Installation Program
0 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ
1 Welcome to the Fusion CD 16 Quick Start Installation Program.
2 Quick Start installs the Fusion CD 16 software and tests your 
2 system to ensure it is ready to run your games and applications.  
2 Quick Start automatically assigns DMA and IRQ settings for the 
2 Fusion CD 16 to use, and updates your DOS and Windows
2 system files.
3 If you want to use a directory other than \FUSION16 to store your 
3 software (\FUSION16 is recommended), press the BACKSPACE key to erase 
3 the name shown below and then type the name of the directory.  
3 Press ENTER to continue when the new directory name is correct.
4 This is a test of the Fusion CD 16 hardware settings.
5 Use the UP and DOWN arrow keys to highlight an item and press ENTER
5 to select.
6 Quick Start is now ready to copy files into the directory shown 
6 below.
7 Below are the values Quick Start selected for your Fusion CD 16.
7 You will hear a test sound each time an IRQ or DMA channel is tested.
8 If you want to change any settings, use the UP and DOWN arrow keys to 
8 select and press ENTER.  To continue the installation, select 'Complete 
8 Changes' and press ENTER.
9 The DMA channel setting was determined by Quick Start avoid possible 
9 system conflicts.  Select another available DMA channel if you want to 
9 change this setting.
10 The IRQ setting was determined by Quick Start to avoid system conflicts.
10 Select another available IRQ if you want to change this setting.
10 
11 If you select YES (recommended), your DOS configuration files -
11 CONFIG.SYS and AUTOEXEC.BAT - will be modified.  The previous 
11 versions of these files will be saved as CONFIG.000 and AUTOEXEC.000.
12 Use the UP and DOWN arrow keys and press ENTER to select a setting.
12 Press ESC to cancel.
13 If you select YES, your Windows configuration files (SYSTEM.INI and
13 WIN.INI) will be modified and the previous versions will be saved
13 as SYSTEM.000 and WIN.000.  Also, current Pro AudioSpectrum drivers 
13 in your Windows "system" directory will be updated.
14 Installation Information:
15 Quick Start has finished installing your 
15 Fusion CD 16.  Press F3 to exit to DOS, 
15 then restart your computer by simultaneously 
15 pressing the CTRL-ALT-DEL keys.
16 Unable to perform system test.
17 File Not on Disk...
18 WARNING:  The file listed above was not found!  The installation is not
18           complete.  Press F3 to exit.
19 WARNING:  The Fusion CD 16 may not be
19           fully installed since you did not 
19           choose to update Windows' system files.
20 No changes were made by Quick Start.
21 Error: Unable to copy files.  Please run Quick Start
21 from the installation diskette to Install Software.
22 Press <F3> to exit.   
23 Unable to initialize the Fusion CD 16.
23 Please perform the installation again.  
23 Is the Fusion CD 16 interface card installed? 
23 If so, call Technical Support (800) 638-2807. 
24          Insert the disk with MSCDEX.EXE
24                and press <ENTER>
25 The file FILELIST.TXT has an invalid format.
26 Please Insert the Next Disk...
27 This file is required for unarchiving the
27 installation files.
28 Quick Start detects that the directory shown below 
28 already exists.
29 Press ENTER to continue.
30 Data Compression provided courtesy of LHARC 
30   - Copyright Haruyasu Yoshizaki -
31 If you select YES, the Fusion CD 16 files will be 
31 copied to the directory you specified.
31 If you select NO, the Fusion CD 16 files will NOT be copied.
32 If you select YES, the DMA channel and IRQ settings will be tested.
32 The tests will not be performed if you select NO.
33 If you select YES, the Spectrum 16 joystick port will be enabled.  If you
33 select NO, the joystick will be disabled.  The default setting is YES.
34 Select an IRQ setting.  Quick Start has determined the initial setting
34 to avoid any system conflict.
35 Press ESC if you want to change the name, or 
35 Press F3 to exit Quick Start.
36 WARNING:  
36    Quick Start detected that a DMA channel
36    conflict caused the audio test to stop.  
36    Please manually select DMA channels, and 
36    keep track of the one that caused the 
36    problem - the test for the DMA channels
36    is on the next screen.  Note: Channels 5, 
36    6 and 7 are the usual source of failure.
41 Software has not been installed in the default:
42 directory.  Install the software before setting 
42 up the hardware, or run the install program from
42 the directory where the software is installed.
43 Select a Sound Blaster compatible DMA channel.  Quick 
43 Start has determined the initial setting to avoid system
43 conflict.
44 To enable Sound Blaster Emulation, select YES.  To disable it, select
44 NO.  The default value is YES.
45 To enable MPU-401 Emulation, select YES. To disable it, select NO.
45 The default value is NO.
46 Select a Sound Blaster port address.  Quick Start has 
46 determined the initial setting of port address '220'.
47 Select a Sound Blaster compatible IRQ setting.  Quick Start 
47 has determined the initial setting to avoid system conflict. 
48 Select a Sound Blaster compatible DMA channel.  Quick Start 
48 has determined the initial setting to avoid system conflict.
48   
48 WARNING:  Only DMA 1 is fully Sound Blaster compatible.
49 Select an MPU-401 port address.  The default setting is port "330".
50 Select an MPU-401 IRQ setting.  Quick Start has determined the 
50 initial setting to avoid system conflict.
51 NOTE: Many DOS-based software programs use 
51       IRQ 2 for the MPU-401 feature.  
52 WARNING:  The Fusion CD 16 is not fully 
52           installed since you did not choose to 
52           update the DOS system files.
52 NOTE:     System files are saved before being 
52           modified.  You may undo changes 
52           made by renaming the saved versions 
52           of the original files. 
53 WARNING:  The Fusion CD 16 is not fully installed 
53           since you did not choose to update 
53           the DOS or Windows system files.
53 NOTE:     System files are saved before being modified.
53           You may undo changes made by renaming the saved 
53           versions of the original files. 
58 The default port # is set to 340 for the CD-ROM Drive.
58 This value is determined by Jumper 15 on the sound card.
58   
58 If you have changed this value on the sound card, select the 
58 new value below.  Otherwise, press ENTER to continue.
59 59
60 60
61 61
62 62
63 63
64 64
65 65
66 66
67 67
68 The default IRQ value is set to 3 for the CD-ROM Drive.
68 This value is determined by Jumper 14 on the sound card.
68 
68 If you have changed this value on the sound card, select the 
68 new value below.  Otherwise, press ENTER to continue.